Re: [PATCH] arm64: dts: qcom: sm6115: Set up CPU cooling maps

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 31.05.2023 16:55, Konrad Dybcio wrote:
> 
> 
> On 18.04.2023 17:51, Bjorn Andersson wrote:
>> On Tue, Apr 18, 2023 at 03:01:47PM +0200, Konrad Dybcio wrote:
>>>
>>>
>>> On 18.04.2023 15:02, Bjorn Andersson wrote:
>>>> On Tue, Apr 18, 2023 at 01:56:56PM +0200, Konrad Dybcio wrote:
>>>>> Set up CPU cooling maps to ensure the thermal framework is aware of
>>>>> the connection between the CPUs and the TSENS sensors.
>>>>>
>>>>> All of the maps refer to all 4 CPUs within a given cluster at a time,
>>>>> as that's what can be considered the smallest DVFS target unit - they
>>>>> all share the same voltage line and clock source.
>>>>>
>>>>
>>>> Generally software based CPU cooling is considered too slow to cope with
>>>> CPU core temperature changes, and the limits hardware working together
>>>> with OSM/EPSS will do a better job maintaining appropriate core
>>>> temperature levels.
>>>>
>>>> Is there a reason why this can't be used/relied upon on this platform?
>>> I haven't set up LMH yet and the default limits, at least with my dubious
>>> meta build, seem to let the board go to 75degC with just 4 cores working..
>>>
>>> Not sure if there's a voltage droop when I let it go full throttle or
>>> something, but pushing it to the limit definitely causes the board to be
>>> (even) less stable..
>>>
>>>>
>>>>
>>>> PS. Amending this mechanism with software based cooling to keep the
>>>> system at a reasonable/lower temperature is a good idea.
>>> We don't like burned chips around here!
>>>
>>
>> Limits hardware will help you with that, software based cooling will
>> help avoid burning the user.
> So, are there any reasons not to take this patch?
Bump

Konrad
> 
> Konrad
>>
>> Regards,
>> Bjorn
>>
>>> Konrad
>>>>
>>>> Regards,
>>>> Bjorn
>>>>
>>>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
>>>>> ---
>>>>>  arch/arm64/boot/dts/qcom/sm6115.dtsi | 137 +++++++++++++++++++++++++++++++++++
>>>>>  1 file changed, 137 insertions(+)
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
>>>>> index 631ca327e064..36ff913c1a60 100644
>>>>> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
>>>>> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
>>>>> @@ -12,6 +12,7 @@
>>>>>  #include <dt-bindings/gpio/gpio.h>
>>>>>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>>  #include <dt-bindings/power/qcom-rpmpd.h>
>>>>> +#include <dt-bindings/thermal/thermal.h>
>>>>>  
>>>>>  / {
>>>>>  	interrupt-parent = <&intc>;
>>>>> @@ -47,6 +48,8 @@ CPU0: cpu@0 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_0>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 0>;
>>>>> +			#cooling-cells = <2>;
>>>>> +
>>>>>  			L2_0: l2-cache {
>>>>>  				compatible = "cache";
>>>>>  				cache-level = <2>;
>>>>> @@ -63,6 +66,7 @@ CPU1: cpu@1 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_0>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 0>;
>>>>> +			#cooling-cells = <2>;
>>>>>  		};
>>>>>  
>>>>>  		CPU2: cpu@2 {
>>>>> @@ -75,6 +79,7 @@ CPU2: cpu@2 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_0>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 0>;
>>>>> +			#cooling-cells = <2>;
>>>>>  		};
>>>>>  
>>>>>  		CPU3: cpu@3 {
>>>>> @@ -87,6 +92,7 @@ CPU3: cpu@3 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_0>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 0>;
>>>>> +			#cooling-cells = <2>;
>>>>>  		};
>>>>>  
>>>>>  		CPU4: cpu@100 {
>>>>> @@ -99,6 +105,8 @@ CPU4: cpu@100 {
>>>>>  			dynamic-power-coefficient = <282>;
>>>>>  			next-level-cache = <&L2_1>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 1>;
>>>>> +			#cooling-cells = <2>;
>>>>> +
>>>>>  			L2_1: l2-cache {
>>>>>  				compatible = "cache";
>>>>>  				cache-level = <2>;
>>>>> @@ -115,6 +123,7 @@ CPU5: cpu@101 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_1>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 1>;
>>>>> +			#cooling-cells = <2>;
>>>>>  		};
>>>>>  
>>>>>  		CPU6: cpu@102 {
>>>>> @@ -127,6 +136,7 @@ CPU6: cpu@102 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_1>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 1>;
>>>>> +			#cooling-cells = <2>;
>>>>>  		};
>>>>>  
>>>>>  		CPU7: cpu@103 {
>>>>> @@ -139,6 +149,7 @@ CPU7: cpu@103 {
>>>>>  			enable-method = "psci";
>>>>>  			next-level-cache = <&L2_1>;
>>>>>  			qcom,freq-domain = <&cpufreq_hw 1>;
>>>>> +			#cooling-cells = <2>;
>>>>>  		};
>>>>>  
>>>>>  		cpu-map {
>>>>> @@ -2471,6 +2482,24 @@ cpu4-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 6>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu4_alert0>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu4_alert1>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu4_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>> @@ -2497,6 +2526,24 @@ cpu5-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 7>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu5_alert0>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu5_alert1>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu5_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>> @@ -2523,6 +2570,24 @@ cpu6-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 8>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu6_alert0>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu6_alert1>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu6_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>> @@ -2549,6 +2614,24 @@ cpu7-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 9>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu7_alert0>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu7_alert1>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu7_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>> @@ -2575,6 +2658,24 @@ cpu45-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 10>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu45_alert0>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu45_alert1>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu45_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>> @@ -2601,6 +2702,24 @@ cpu67-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 11>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu67_alert0>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu67_alert1>;
>>>>> +					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu67_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>> @@ -2627,6 +2746,24 @@ cpu0123-thermal {
>>>>>  			polling-delay = <0>;
>>>>>  			thermal-sensors = <&tsens0 12>;
>>>>>  
>>>>> +			cooling-maps {
>>>>> +				map0 {
>>>>> +					trip = <&cpu0123_alert0>;
>>>>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +
>>>>> +				map1 {
>>>>> +					trip = <&cpu0123_alert1>;
>>>>> +					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>>>>> +							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>>>>> +				};
>>>>> +			};
>>>>> +
>>>>>  			trips {
>>>>>  				cpu0123_alert0: trip-point0 {
>>>>>  					temperature = <90000>;
>>>>>
>>>>> ---
>>>>> base-commit: 4aa1da8d99724f6c0b762b58a71cee7c5e2e109b
>>>>> change-id: 20230418-topic-cool_bengal-2f5f3f47269c
>>>>>
>>>>> Best regards,
>>>>> -- 
>>>>> Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
>>>>>



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux