For the regulators, apply the same settings as in the downstream devicetree [1], including the "regulator-always-on" for the SAFE_LDO. For the voltage of SAFE_LDO, however, there is only one voltage of 4.9 V available in the mainline driver [2][3]. The values of the battery data evolve from following sources: - precharge current: 450 mA corresponds to the default value of the chip. It doesn't get changed by the downstream Android driver. Therefore let's stick to this value. - constant charge current: The 1000 mA are taken from the downstream devicetree of the serranove battery. It's not easy to spot. The value is in the line "input_current_limit" [4]. The rows are according to the power supply type, the 4th value stands for "main supply" [5]. That's the value used by the Android driver when a charging cable is plugged into the device. - charge termination current: In the downstream devicetree of the battery that's the line "full_check_current_1st", which contains the 150 mA [6]. - precharge voltage: This one doesn't get set in the downstream Android driver. The chip's default is 2.8 V. That seemed too low to have a notable effect of handling the battery gentle. The chosen value of 3.5 V is a bit arbitrary and possibly rather high. As the device is already several years old and therefore most batteries too, a value on the safe side seems reasonable. - constant charge voltage: The value of 4.35 V is set in the line "chg_float_voltage" of the downstream battery devicetree [7]. The "connector" sub-node in the extcon node, the "battery" node in the general section and the line "power-supplies" in the fuel-gauge node result from the way of implementation documented in the dt-bindings of rt5033-charger [8] and mfd rt5033 [9]. [1] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-eur-r03.dtsi#L135-L181 [2] https://github.com/torvalds/linux/blob/v6.3/include/linux/mfd/rt5033-private.h#L211-L212 [3] https://github.com/torvalds/linux/blob/v6.3/drivers/regulator/rt5033-regulator.c#L83 [4] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-battery-r01.dtsi#L100 [5] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/include/linux/power_supply.h#L173-L177 [6] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-battery-r01.dtsi#L102 [7] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-battery-r01.dtsi#L95 [8] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/Documentation/devicetree/bindings/power/supply/richtek,rt5033-charger.yaml?h=next-20230616 [9] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/Documentation/devicetree/bindings/mfd/richtek,rt5033.yaml?h=next-20230616 Signed-off-by: Jakob Hauser <jahau@xxxxxxxxxxxxxx> --- The patch is based on linux-next "next-20230616". The driver rt5033-charger was just recently added to linux-next. RESEND because I used an outdated e-mail address of Bjorn before. .../dts/qcom/msm8916-samsung-serranove.dts | 67 ++++++++++++++++++- 1 file changed, 66 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts index 15dc246e84e2..2114d26548db 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts @@ -142,6 +142,12 @@ muic: extcon@14 { pinctrl-names = "default"; pinctrl-0 = <&muic_irq_default>; + + usb_con: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; }; }; @@ -199,6 +205,15 @@ nfc@2b { pinctrl-0 = <&nfc_default>; }; }; + + battery: battery { + compatible = "simple-battery"; + precharge-current-microamp = <450000>; + constant-charge-current-max-microamp = <1000000>; + charge-term-current-microamp = <150000>; + precharge-upper-limit-microvolt = <3500000>; + constant-charge-voltage-max-microvolt = <4350000>; + }; }; &blsp_i2c2 { @@ -228,7 +243,7 @@ magnetometer@2e { &blsp_i2c4 { status = "okay"; - battery@35 { + fuel-gauge@35 { compatible = "richtek,rt5033-battery"; reg = <0x35>; @@ -237,6 +252,8 @@ battery@35 { pinctrl-names = "default"; pinctrl-0 = <&fg_alert_default>; + + power-supplies = <&rt5033_charger>; }; }; @@ -261,6 +278,46 @@ touchscreen@20 { }; }; +&blsp_i2c6 { + status = "okay"; + + pmic@34 { + compatible = "richtek,rt5033"; + reg = <0x34>; + + interrupt-parent = <&tlmm>; + interrupts = <62 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_default>; + + regulators { + safe_ldo_reg: SAFE_LDO { + regulator-name = "SAFE_LDO"; + regulator-min-microvolt = <4900000>; + regulator-max-microvolt = <4900000>; + regulator-always-on; + }; + ldo_reg: LDO { + regulator-name = "LDO"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + buck_reg: BUCK { + regulator-name = "BUCK"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + }; + + rt5033_charger: charger { + compatible = "richtek,rt5033-charger"; + monitored-battery = <&battery>; + richtek,usb-connector = <&usb_con>; + }; + }; +}; + &blsp_uart2 { status = "okay"; }; @@ -387,6 +444,14 @@ nfc_i2c_default: nfc-i2c-default-state { bias-disable; }; + pmic_int_default: pmic-int-default-state { + pins = "gpio62"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + tkey_default: tkey-default-state { pins = "gpio98"; function = "gpio"; -- 2.39.2
