Re: [PATCH] drm/msm/dsi: Enable BURST_MODE for command mode for DSI 6G v1.3+

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 6/14/2023 2:43 AM, Marijn Suijten wrote:
On 2023-06-12 16:37:36, Jessica Zhang wrote:
During a frame transfer in command mode, there could be frequent
LP11 <-> HS transitions when multiple DCS commands are sent mid-frame or
if the DSI controller is running on slow clock and is throttled. To
minimize frame latency due to these transitions, it is recommended to
send the frame in a single burst.

This feature is supported for DSI 6G 1.3 and above, thus enable burst
mode if supported.

Signed-off-by: Jessica Zhang <quic_jesszhan@xxxxxxxxxxx>
---
  drivers/gpu/drm/msm/dsi/dsi_host.c | 5 +++++
  1 file changed, 5 insertions(+)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
index 744f2398a6d6..8254b06dca85 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -994,6 +994,11 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi)
  		dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL,
  			DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) |
  			DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay));
+
+		if (msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G &&
+				msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V1_3)
+			dsi_write(msm_host, REG_DSI_CMD_MODE_MDP_CTRL2,
+					DSI_CMD_MODE_MDP_CTRL2_BURST_MODE);

This is not part of the timing setup, and a similar BURST_MODE flag is
enabled for video-mode in dsi_ctrl_config() - should it be moved there?

Hi Marijn,

Sure, I can move the change to dsi_ctrl_enable() instead.


(There is a dsi_sw_reset() in between the calls to dsi_timing_setup()
  and dsi_ctrl_cfg())

Note that that function sets up the CMD_CFG0 and CMD_CFG1 register, with
the former having a very similar layout to MDP_CTRL2... is there
documentation outlining the difference?

I see what you mean, but unfortunately I'm not able to give you any documentation about the differences between them.

FWIW, I think the macros in dsi.xml.h should give you a sense of what's within the registers and the slight differences between them.

Thanks,

Jessica Zhang


- Marijn

  	}
  }
---
base-commit: dd969f852ba4c66938c71889e826aa8e5300d2f2
change-id: 20230608-b4-add-burst-mode-a5bb144069fa

Best regards,
--
Jessica Zhang <quic_jesszhan@xxxxxxxxxxx>




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux