DSI 6G v2.5.x+ supports a data-bus widen mode that allows DSI to send 48 bits of compressed data per pclk instead of 24. For all chipsets that support this mode, enable it whenever DSC is enabled as recommend by the hardware programming guide. Only enable this for command mode as we are currently unable to validate it for video mode. Signed-off-by: Jessica Zhang <quic_jesszhan@xxxxxxxxxxx> --- Note: The dsi.xml.h changes were generated using the headergen2 script in envytools [1], but the changes to the copyright and rules-ng-ng source file paths were dropped. [1] https://github.com/freedreno/envytools/ drivers/gpu/drm/msm/dsi/dsi.xml.h | 1 + drivers/gpu/drm/msm/dsi/dsi_host.c | 19 ++++++++++++++++++- 2 files changed, 19 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/msm/dsi/dsi.xml.h b/drivers/gpu/drm/msm/dsi/dsi.xml.h index a4a154601114..2a7d980e12c3 100644 --- a/drivers/gpu/drm/msm/dsi/dsi.xml.h +++ b/drivers/gpu/drm/msm/dsi/dsi.xml.h @@ -664,6 +664,7 @@ static inline uint32_t DSI_CMD_MODE_MDP_CTRL2_INPUT_RGB_SWAP(enum dsi_rgb_swap v return ((val) << DSI_CMD_MODE_MDP_CTRL2_INPUT_RGB_SWAP__SHIFT) & DSI_CMD_MODE_MDP_CTRL2_INPUT_RGB_SWAP__MASK; } #define DSI_CMD_MODE_MDP_CTRL2_BURST_MODE 0x00010000 +#define DSI_CMD_MODE_MDP_CTRL2_DATABUS_WIDEN 0x00100000 #define REG_DSI_CMD_MODE_MDP_STREAM2_CTRL 0x000001b8 #define DSI_CMD_MODE_MDP_STREAM2_CTRL_DATA_TYPE__MASK 0x0000003f diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c index 5d7b4409e4e9..1da5238e7105 100644 --- a/drivers/gpu/drm/msm/dsi/dsi_host.c +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c @@ -927,6 +927,9 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi) u32 hdisplay = mode->hdisplay; u32 wc; int ret; + bool widebus_supported = msm_host->cfg_hnd->major == MSM_DSI_VER_MAJOR_6G && + msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V2_5_0; + DBG(""); @@ -973,8 +976,15 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi) * * hdisplay will be divided by 3 here to account for the fact * that DPU sends 3 bytes per pclk cycle to DSI. + * + * If widebus is supported, set DATABUS_WIDEN register and divide hdisplay by 6 + * instead of 3 */ - hdisplay = DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 3); + if (!(msm_host->mode_flags & MIPI_DSI_MODE_VIDEO) && widebus_supported) + hdisplay = DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 6); + else + hdisplay = DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 3); + h_total += hdisplay; ha_end = ha_start + hdisplay; } @@ -1027,6 +1037,13 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi) dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL, DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) | DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay)); + + if (msm_host->dsc && widebus_supported) { + u32 mdp_ctrl2 = dsi_read(msm_host, REG_DSI_CMD_MODE_MDP_CTRL2); + + mdp_ctrl2 |= DSI_CMD_MODE_MDP_CTRL2_DATABUS_WIDEN; + dsi_write(msm_host, REG_DSI_CMD_MODE_MDP_CTRL2, mdp_ctrl2); + } } } -- 2.40.1
