On Wed, Jun 07, 2023 at 02:07:31PM +0300, Dmitry Baryshkov wrote:
> On 07/06/2023 13:48, Varadarajan Narayanan wrote:
> >Add USB phy and controller related nodes
> >
> >SS PHY need two supplies and HS PHY needs three supplies. 0.925V
> >and 3.3V are from fixed regulators and 1.8V is generated from
> >PMIC's LDO
> >
> >Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> >Signed-off-by: Varadarajan Narayanan <quic_varada@xxxxxxxxxxx>
> >---
> > Changes in v12:
> > - Rebase
> > Changes in v11:
> > - Rename dwc_0 -> usb_0_dwc3
> > Changes in v10:
> > - Fix regulator definitions
> > Changes in v8:
> > - Change clocks order to match the bindings
> > Changes in v7:
> > - Change com_aux -> cfg_ahb
> > Changes in v6:
> > - Introduce fixed regulators for the phy
> > - Resolved all 'make dtbs_check' messages
> >
> > Changes in v5:
> > - Fix additional comments
> > - Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml
> > - 'make dtbs_check' giving the following messages since
> > ipq9574 doesn't have power domains. Hope this is ok
> >
> > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property
> > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml
> > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property
> > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> >
> > Changes in v4:
> > - Use newer bindings without subnodes
> > - Fix coding style issues
> >
> > Changes in v3:
> > - Insert the nodes at proper location
> >
> > Changes in v2:
> > - Fixed issues flagged by Krzysztof
> > - Fix issues reported by make dtbs_check
> > - Remove NOC related clocks (to be added with proper
> > interconnect support)
> >---
> > arch/arm64/boot/dts/qcom/ipq9574.dtsi | 104 ++++++++++++++++++++++++++++++++++
> > 1 file changed, 104 insertions(+)
> >
> >diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> >index 0baeb10..8f7c59e 100644
> >--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> >+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> >@@ -94,6 +94,24 @@
> > };
> > };
> >+ fixed_3p3: s3300 {
> >+ compatible = "regulator-fixed";
> >+ regulator-min-microvolt = <3300000>;
> >+ regulator-max-microvolt = <3300000>;
> >+ regulator-boot-on;
> >+ regulator-always-on;
> >+ regulator-name = "fixed_3p3";
> >+ };
> >+
> >+ fixed_0p925: s0925 {
> >+ compatible = "regulator-fixed";
> >+ regulator-min-microvolt = <925000>;
> >+ regulator-max-microvolt = <925000>;
> >+ regulator-boot-on;
> >+ regulator-always-on;
> >+ regulator-name = "fixed_0p925";
> >+ };
> >+
>
> These regulators are provided by the board, not by the SoC itself. As such
> they should go to the board DT files. Please excuse me for not noticing this
> during earlier review stage. I was too concentrated on not making them
> non-USB-specific.
Will move it to board dts.
Thanks
Varada
> > memory@40000000 {
> > device_type = "memory";
> > /* We expect the bootloader to fill in the size */
> >@@ -465,6 +483,92 @@
> > status = "disabled";
> > };
> >+ usb_0_qusbphy: phy@7b000 {
> >+ compatible = "qcom,ipq9574-qusb2-phy";
> >+ reg = <0x0007b000 0x180>;
> >+ #phy-cells = <0>;
> >+
> >+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> >+ <&xo_board_clk>;
> >+ clock-names = "cfg_ahb",
> >+ "ref";
> >+
> >+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
> >+ status = "disabled";
> >+ };
> >+
> >+ usb_0_qmpphy: phy@7d000 {
> >+ compatible = "qcom,ipq9574-qmp-usb3-phy";
> >+ reg = <0x0007d000 0xa00>;
> >+ #phy-cells = <0>;
> >+
> >+ clocks = <&gcc GCC_USB0_AUX_CLK>,
> >+ <&xo_board_clk>,
> >+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> >+ <&gcc GCC_USB0_PIPE_CLK>;
> >+ clock-names = "aux",
> >+ "ref",
> >+ "cfg_ahb",
> >+ "pipe";
> >+
> >+ resets = <&gcc GCC_USB0_PHY_BCR>,
> >+ <&gcc GCC_USB3PHY_0_PHY_BCR>;
> >+ reset-names = "phy",
> >+ "phy_phy";
> >+
> >+ status = "disabled";
> >+
> >+ #clock-cells = <0>;
> >+ clock-output-names = "usb0_pipe_clk";
> >+ };
> >+
> >+ usb3: usb@8af8800 {
> >+ compatible = "qcom,ipq9574-dwc3", "qcom,dwc3";
> >+ reg = <0x08af8800 0x400>;
> >+ #address-cells = <1>;
> >+ #size-cells = <1>;
> >+ ranges;
> >+
> >+ clocks = <&gcc GCC_SNOC_USB_CLK>,
> >+ <&gcc GCC_USB0_MASTER_CLK>,
> >+ <&gcc GCC_ANOC_USB_AXI_CLK>,
> >+ <&gcc GCC_USB0_SLEEP_CLK>,
> >+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> >+
> >+ clock-names = "cfg_noc",
> >+ "core",
> >+ "iface",
> >+ "sleep",
> >+ "mock_utmi";
> >+
> >+ assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>,
> >+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> >+ assigned-clock-rates = <200000000>,
> >+ <24000000>;
> >+
> >+ interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
> >+ interrupt-names = "pwr_event";
> >+
> >+ resets = <&gcc GCC_USB_BCR>;
> >+ status = "disabled";
> >+
> >+ usb_0_dwc3: usb@8a00000 {
> >+ compatible = "snps,dwc3";
> >+ reg = <0x8a00000 0xcd00>;
> >+ clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> >+ clock-names = "ref";
> >+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> >+ phys = <&usb_0_qusbphy>, <&usb_0_qmpphy>;
> >+ phy-names = "usb2-phy", "usb3-phy";
> >+ tx-fifo-resize;
> >+ snps,is-utmi-l1-suspend;
> >+ snps,hird-threshold = /bits/ 8 <0x0>;
> >+ snps,dis_u2_susphy_quirk;
> >+ snps,dis_u3_susphy_quirk;
> >+ dr_mode = "host";
> >+ };
> >+ };
> >+
> > intc: interrupt-controller@b000000 {
> > compatible = "qcom,msm-qgic2";
> > reg = <0x0b000000 0x1000>, /* GICD */
>
> --
> With best wishes
> Dmitry
>
