Re: [PATCH V2 11/13] arm64: dtsi: qcom: ipq5018: enable nodes required for multipd

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 6/5/2023 11:05 AM, Manikanta Mylavarapu wrote:


On 5/30/2023 4:35 PM, Krzysztof Kozlowski wrote:
On 22/05/2023 00:28, Manikanta Mylavarapu wrote:
Enable nodes required for multipd remoteproc bring up

Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.

It is "dts". Not "dtsi".

Sure, I will update to 'dtsi'.

Sorry please discard my previous reply.
I will update to dts.


Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@xxxxxxxxxxx>
---
Changes in V2:
    - Corrected syntax like alignmnet and kept nodes in sorted order.
    - Covered entire TCSR region.
    - Added 'firmware-name' property.

  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 140 ++++++++++++++++++++++++++
  1 file changed, 140 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 9f13d2dcdfd5..3772d54d89e4 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -85,6 +85,18 @@
              reg = <0x0 0x4ac00000 0x0 0x200000>;
              no-map;
          };
+
+        q6_region: wcnss@4b000000 {
+            reg = <0x0 0x4b000000 0x0 0x1700000>;
+            no-map;
+        };
+
+        smem@4ab00000 {
+            compatible = "qcom,smem";
+            reg = <0x0 0x4ab00000 0x0 0x100000>;
+            hwlocks = <&tcsr_mutex 0>;
+            no-map;
+        };
      };

      soc: soc@0 {
@@ -128,6 +140,12 @@
              #power-domain-cells = <1>;
          };

+        tcsr_mutex: hwlock@1905000 {
+            compatible = "qcom,tcsr-mutex";
+            reg = <0x01905000 0x20000>;
+            #hwlock-cells = <1>;
+        };
+
          sdhc_1: mmc@7804000 {
              compatible = "qcom,ipq5018-sdhci", "qcom,sdhci-msm-v5";
              reg = <0x7804000 0x1000>;
@@ -181,6 +199,14 @@
              };
          };

+        apcs_glb: mailbox@b111000 {
+            compatible = "qcom,ipq5018-apcs-apps-global",
+                     "qcom,ipq6018-apcs-apps-global";
+            reg = <0x0b111000 0x1000>;
+            #clock-cells = <1>;
+            #mbox-cells = <1>;
+        };
+
          timer@b120000 {
              compatible = "arm,armv7-timer-mem";
              reg = <0x0b120000 0x1000>;
@@ -238,6 +264,96 @@
                  status = "disabled";
              };
          };
+
+        q6v5_wcss: remoteproc@cd00000 {
+            compatible = "qcom,ipq5018-q6-mpd";
+            reg = <0x0cd00000 0x4040>;
+            firmware-name = "IPQ5018/q6_fw.mdt",
+                    "IPQ5018/m3_fw.mdt",
+                    "qcn6122/m3_fw.mdt";
+            interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>,
+                          <&wcss_smp2p_in 0 0>,
+                          <&wcss_smp2p_in 1 0>,
+                          <&wcss_smp2p_in 2 0>,
+                          <&wcss_smp2p_in 3 0>;
+            interrupt-names = "wdog",
+                      "fatal",
+                      "ready",
+                      "handover",
+                      "stop-ack";
+
+            qcom,smem-states = <&wcss_smp2p_out 0>,
+                       <&wcss_smp2p_out 1>;
+            qcom,smem-state-names = "shutdown",
+                        "stop";
+            memory-region = <&q6_region>;
+
+            glink-edge {
+                interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+                label = "rtr";
+                qcom,remote-pid = <1>;
+                mboxes = <&apcs_glb 8>;
+            };
+
+            pd-1 {
+                compatible = "qcom,ipq5018-wcss-ahb-mpd";
+                firmware-name = "IPQ5018/q6_fw.mdt";
+                interrupts-extended = <&wcss_smp2p_in 8 0>,
+                              <&wcss_smp2p_in 9 0>,
+                              <&wcss_smp2p_in 12 0>,
+                              <&wcss_smp2p_in 11 0>;

What "0" stands for?

0 means IRQ_NONE. These are software interrupts (register write),
so we have configured to 0. I will replace 0 with IRQ_NONE.

Thanks & Regards,
Manikanta.

+                interrupt-names = "fatal",
+                          "ready",
Best regards,
Krzysztof




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux