Il giorno mer 31 mag 2023 alle ore 15:01 Manivannan Sadhasivam <mani@xxxxxxxxxx> ha scritto: > > On Wed, May 31, 2023 at 01:44:24PM +0200, Daniele Palmas wrote: > > Il giorno mar 30 mag 2023 alle ore 15:56 Manivannan Sadhasivam > > <mani@xxxxxxxxxx> ha scritto: > > > > > > On Tue, May 30, 2023 at 01:12:59PM +0200, Daniele Palmas wrote: > > > > Hi Mani, > > > > > > > > Il giorno mar 30 mag 2023 alle ore 12:31 Manivannan Sadhasivam > > > > <mani@xxxxxxxxxx> ha scritto: > > > > > > > > > > On Tue, May 30, 2023 at 11:13:40AM +0200, Daniele Palmas wrote: > > > > > > There are situations in which SBL is a legitimate initial execution > > > > > > environment (e.g. modem stuck in SBL due to a firmware failure...), but > > > > > > mhi refuses to start: > > > > > > > > > > > > mhi-pci-generic 0000:01:00.0: MHI PCI device found: foxconn-sdx55 > > > > > > mhi-pci-generic 0000:01:00.0: BAR 0: assigned > > > > > > mhi-pci-generic 0000:01:00.0: enabling device (0000 -> 0002) > > > > > > mhi mhi0: Requested to power ON > > > > > > mhi mhi0: SECONDARY BOOTLOADER is not a valid EE for power on > > > > > > mhi-pci-generic 0000:01:00.0: failed to power up MHI controller > > > > > > mhi-pci-generic: probe of 0000:01:00.0 failed with error -5 > > > > > > > > > > > > Fix this by adding SBL as an allowed initial execution environment. > > > > > > > > > > > > > > > > What can you do with the modem when firmware failure happens? If there is a > > > > > usecase, please explain. > > > > > > > > (removing Siddartha and Sujeev due to addresses not working) > > > > > > > > > > Both left Qualcomm a while ago... > > > > > > > A possible scenario for a Telit modem not being able to go to mission > > > > mode is when a firmware update does not work properly: in this case it > > > > remains stuck in SBL, but the SAHARA device can be used for retrying > > > > the firmware update. > > > > > > > > > > So IIUC, while updating SBL over SAHARA channel, the firmware update could be > > > corrupted and the device would get stuck in SBL EE. In that case, the SAHARA > > > channel exposed by PBL will still be open and that could be used to retry the > > > firmware update. Am I right? > > > > > > Looks like PBL is doing a fail safe upgrade! > > > > > > > Yes, the scenario is a broken firmware update. > > > > Telit has implemented custom code in the SBL for allowing the firmware > > update through a custom protocol using the SAHARA channels: this has > > been mainly done to avoid sharing with customers Qualcomm IP about > > firmware update, since it is usually problematic. > > > > Firmware update is fail safe in the sense that it is guaranteed that > > the modem will always power-up at least in SBL, in which the firmware > > update can always be retried. I don't have the exact details of what > > is happening inside the modem, but, if required, I can get them. > > > > Okay, I didn't now that it is a custom SBL, so yeah it may not benefit other > platforms. But what is the userspace tool that you are using to download > firmware over SAHARA? The userspace tool is not public at the moment, but will check about the plans for open-sourcing. > Can QDL be used? I will check that with firmware developers. Reading also Jeffrey's reply, since this looks like a Telit modem quirk, I'm wondering if it could make sense to deal with this again once the quirk framework at https://lore.kernel.org/mhi/20230519163902.4170-2-quic_jhugo@xxxxxxxxxxx/T/#u gets merged, otherwise I guess we can continue living with custom patches. Thanks, Daniele > - Mani > > > > > Telit FN990 supports the SAHARA channels in pci_generic. It's true > > > > that there's still missing the exposed device for userspace, something > > > > that we are currently managing with out of tree patches, but I see > > > > that there's some ongoing effort for that > > > > https://lore.kernel.org/mhi/20230522190459.13790-1-quic_jhugo@xxxxxxxxxxx/ > > > > > > > > I'm not sure if non-Telit modems have other reasonable use-cases. > > > > > > > > > > If my above understanding is correct, then this patch will benefit other > > > platforms too. > > > > > > > Well... I can't comment on that, since I don't know if the above > > described behavior is due to Telit custom SBL. > > > > Anyway, maybe there could be other scenarios like, for example, modem > > falling into core dump mode in a very early stage? Not sure... > > > > Regards, > > Daniele > > > > > - Mani > > > > > > > Regards, > > > > Daniele > > > > > > > > > > > > > > - Mani > > > > > > > > > > > Fixes: 3000f85b8f47 ("bus: mhi: core: Add support for basic PM operations") > > > > > > Signed-off-by: Daniele Palmas <dnlplm@xxxxxxxxx> > > > > > > --- > > > > > > drivers/bus/mhi/host/internal.h | 2 +- > > > > > > drivers/bus/mhi/host/pm.c | 3 ++- > > > > > > 2 files changed, 3 insertions(+), 2 deletions(-) > > > > > > > > > > > > diff --git a/drivers/bus/mhi/host/internal.h b/drivers/bus/mhi/host/internal.h > > > > > > index 2e139e76de4c..3bdcd2321aa5 100644 > > > > > > --- a/drivers/bus/mhi/host/internal.h > > > > > > +++ b/drivers/bus/mhi/host/internal.h > > > > > > @@ -56,7 +56,7 @@ extern const char * const mhi_ee_str[MHI_EE_MAX]; > > > > > > > > > > > > #define MHI_IN_PBL(ee) (ee == MHI_EE_PBL || ee == MHI_EE_PTHRU || \ > > > > > > ee == MHI_EE_EDL) > > > > > > -#define MHI_POWER_UP_CAPABLE(ee) (MHI_IN_PBL(ee) || ee == MHI_EE_AMSS) > > > > > > +#define MHI_POWER_UP_CAPABLE(ee) (MHI_IN_PBL(ee) || ee == MHI_EE_AMSS || ee == MHI_EE_SBL) > > > > > > #define MHI_FW_LOAD_CAPABLE(ee) (ee == MHI_EE_PBL || ee == MHI_EE_EDL) > > > > > > #define MHI_IN_MISSION_MODE(ee) (ee == MHI_EE_AMSS || ee == MHI_EE_WFW || \ > > > > > > ee == MHI_EE_FP) > > > > > > diff --git a/drivers/bus/mhi/host/pm.c b/drivers/bus/mhi/host/pm.c > > > > > > index 083459028a4b..18872c5017be 100644 > > > > > > --- a/drivers/bus/mhi/host/pm.c > > > > > > +++ b/drivers/bus/mhi/host/pm.c > > > > > > @@ -1203,10 +1203,11 @@ int mhi_sync_power_up(struct mhi_controller *mhi_cntrl) > > > > > > > > > > > > wait_event_timeout(mhi_cntrl->state_event, > > > > > > MHI_IN_MISSION_MODE(mhi_cntrl->ee) || > > > > > > + mhi_cntrl->ee == MHI_EE_SBL || > > > > > > MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state), > > > > > > msecs_to_jiffies(mhi_cntrl->timeout_ms)); > > > > > > > > > > > > - ret = (MHI_IN_MISSION_MODE(mhi_cntrl->ee)) ? 0 : -ETIMEDOUT; > > > > > > + ret = (MHI_IN_MISSION_MODE(mhi_cntrl->ee) || mhi_cntrl->ee == MHI_EE_SBL) ? 0 : -ETIMEDOUT; > > > > > > if (ret) > > > > > > mhi_power_down(mhi_cntrl, false); > > > > > > > > > > > > -- > > > > > > 2.37.1 > > > > > > > > > > > > > > > > -- > > > > > மணிவண்ணன் சதாசிவம் > > > > > > -- > > > மணிவண்ணன் சதாசிவம் > > -- > மணிவண்ணன் சதாசிவம்
