The bam_dma driver needs to know the number of channels and execution environments (EEs) at probe time. If we are in full control of the BAM controller this information can be obtained from the BAM identification registers (BAM_REVISION/BAM_NUM_PIPES). When the BAM is "controlled remotely" it is more complicated. The BAM might not be on at probe time, so reading the registers could fail. This is why the information must be added to the device tree in this case, using "num-channels" and "qcom,num-ees". However, there are also some BAM instances that are initialized by something else but we still have a clock that allows to turn it on when needed. This can be set up in the DT with "qcom,controlled-remotely" and "clocks" and is already supported by the bam_dma driver. Examples for this are the typical BLSP BAM instances on older SoCs, QPIC BAM (for NAND) and the crypto BAM on some SoCs. In this case, there is no need to read "num-channels" and "qcom,num-ees" from the DT. The BAN can be turned on using the clock so we can just read it from the BAM registers like in the normal case. Check for the BAM clock earlier and skip reading "num-channels" and "qcom,num-ees" if it is present to allow simplifying the DT description a bit. Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx> --- Changes in v2: - Rewrite commit message for more clarity (discussion with Bhupesh) - Link to v1: https://lore.kernel.org/r/20230518-bamclk-dt-v1-1-82f738c897d9@xxxxxxxxxxx --- drivers/dma/qcom/bam_dma.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/drivers/dma/qcom/bam_dma.c b/drivers/dma/qcom/bam_dma.c index 1e47d27e1f81..4c3eb972039d 100644 --- a/drivers/dma/qcom/bam_dma.c +++ b/drivers/dma/qcom/bam_dma.c @@ -1272,7 +1272,15 @@ static int bam_dma_probe(struct platform_device *pdev) bdev->powered_remotely = of_property_read_bool(pdev->dev.of_node, "qcom,powered-remotely"); - if (bdev->controlled_remotely || bdev->powered_remotely) { + if (bdev->controlled_remotely || bdev->powered_remotely) + bdev->bamclk = devm_clk_get_optional(bdev->dev, "bam_clk"); + else + bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk"); + + if (IS_ERR(bdev->bamclk)) + return PTR_ERR(bdev->bamclk); + + if (!bdev->bamclk) { ret = of_property_read_u32(pdev->dev.of_node, "num-channels", &bdev->num_channels); if (ret) @@ -1284,14 +1292,6 @@ static int bam_dma_probe(struct platform_device *pdev) dev_err(bdev->dev, "num-ees unspecified in dt\n"); } - if (bdev->controlled_remotely || bdev->powered_remotely) - bdev->bamclk = devm_clk_get_optional(bdev->dev, "bam_clk"); - else - bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk"); - - if (IS_ERR(bdev->bamclk)) - return PTR_ERR(bdev->bamclk); - ret = clk_prepare_enable(bdev->bamclk); if (ret) { dev_err(bdev->dev, "failed to prepare/enable clock\n"); --- base-commit: 2437d5ea2191f3059246a1a7ac6fc4c8cc004dec change-id: 20230518-bamclk-dt-d44bae47b337 Best regards, -- Stephan Gerhold <stephan@xxxxxxxxxxx>
