Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/apq8016-sbc.dts | 153 +++++----------------
arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts | 115 ++--------------
.../boot/dts/qcom/msm8916-alcatel-idol347.dts | 110 +--------------
arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts | 110 +--------------
arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts | 110 +--------------
arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts | 120 +++-------------
.../boot/dts/qcom/msm8916-longcheer-l8150.dts | 110 +--------------
.../boot/dts/qcom/msm8916-longcheer-l8910.dts | 110 +--------------
arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi | 102 +++++++++++---
.../dts/qcom/msm8916-samsung-a2015-common.dtsi | 110 +--------------
.../boot/dts/qcom/msm8916-samsung-gt5-common.dtsi | 110 +--------------
.../boot/dts/qcom/msm8916-samsung-j5-common.dtsi | 103 --------------
.../boot/dts/qcom/msm8916-samsung-serranove.dts | 103 --------------
arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi | 103 --------------
.../boot/dts/qcom/msm8916-wingtech-wt88047.dts | 119 +++-------------
15 files changed, 210 insertions(+), 1478 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
index 7d7af6406c39..ab8dfd858025 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
@@ -329,6 +329,40 @@ &pm8916_resin {
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ /*
+ * The 96Boards specification expects a 1.8V power rail on the low-speed
+ * expansion connector that is able to provide at least 0.18W / 100 mA.
+ * L15/L16 are connected in parallel to provide 55 mA each. A minimum load
+ * must be specified to ensure the regulators are not put in LPM where they
+ * would only provide 5 mA.
+ */
+ pm8916_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-system-load = <50000>;
+ regulator-allow-set-load;
+ regulator-always-on;
+ };
+ pm8916_l16: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-system-load = <50000>;
+ regulator-allow-set-load;
+ regulator-always-on;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&pm8916_s4 {
+ regulator-always-on;
+ regulator-boot-on;
+};
+
&sdhc_1 {
status = "okay";
@@ -446,125 +480,6 @@ &wcnss_iris {
&stm { status = "okay"; };
&tpiu { status = "okay"; };
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- /*
- * The 96Boards specification expects a 1.8V power rail on the low-speed
- * expansion connector that is able to provide at least 0.18W / 100 mA.
- * L15/L16 are connected in parallel to provide 55 mA each. A minimum load
- * must be specified to ensure the regulators are not put in LPM where they
- * would only provide 5 mA.
- */
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-system-load = <50000>;
- regulator-allow-set-load;
- regulator-always-on;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-system-load = <50000>;
- regulator-allow-set-load;
- regulator-always-on;
- };
-
- l17 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
/*
* 2mA drive strength is not enough when connecting multiple
* I2C devices with different pull up resistors.
diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
index 0d517804e44e..753413b48751 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -114,6 +114,18 @@ &pm8916_resin {
status = "okay";
};
+&pm8916_rpm_regulators {
+ pm8916_l16: l16 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_vib {
status = "okay";
};
@@ -153,109 +165,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
accel_int_default: accel-int-default-state {
pins = "gpio115";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
index ddd64cc46998..4bfbad669b1e 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
@@ -156,6 +156,13 @@ &pm8916_resin {
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_vib {
status = "okay";
};
@@ -195,109 +202,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
accel_int_default: accel-int-default-state {
pins = "gpio31";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
index 982457503a3c..37755e885395 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
@@ -128,6 +128,13 @@ &blsp1_uart2 {
status = "okay";
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&sdhc_1 {
status = "okay";
@@ -163,109 +170,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
gpio_keys_default: gpio-keys-default-state {
pins = "gpio107", "gpio117";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts
index 9584d271c526..4a6bf99c755f 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts
@@ -114,6 +114,13 @@ &pm8916_resin {
status = "okay";
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_vib {
status = "okay";
};
@@ -153,109 +160,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
camera_flash_default: camera-flash-default-state {
pins = "gpio31", "gpio32";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
index 8197710372ad..29aaa35438a3 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
@@ -222,11 +222,28 @@ &lpass_codec {
status = "okay";
};
+&pm8916_l8 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+};
+
&pm8916_resin {
status = "okay";
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ pm8916_l16: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_vib {
status = "okay";
};
@@ -321,109 +338,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
accel_irq_default: accel-irq-default-state {
pins = "gpio115";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
index 68d1b76aaf77..b7b1f1ceaf1f 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
@@ -223,6 +223,13 @@ &pm8916_resin {
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_usbin {
status = "okay";
};
@@ -267,109 +274,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
accel_int_default: accel-int-default-state {
pins = "gpio116";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
index 5ef51d3e9098..d1eb3f2ecf3f 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
@@ -95,6 +95,13 @@ &pm8916_resin {
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_vib {
status = "okay";
};
@@ -134,109 +141,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
button_backlight_default: button-backlight-default-state {
pins = "gpio17";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi
index 29ef46c33350..b38eecbd6253 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi
@@ -61,30 +61,92 @@ &wcnss_iris {
};
&rpm_requests {
- smd_rpm_regulators: regulators {
+ pm8916_rpm_regulators: regulators {
compatible = "qcom,rpm-pm8916-regulators";
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
/* pm8916_s1 is managed by rpmpd (MSM8916_VDDCX) */
- pm8916_s3: s3 {};
- pm8916_s4: s4 {};
- pm8916_l1: l1 {};
- pm8916_l2: l2 {};
+ pm8916_s3: s3 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ pm8916_s4: s4 {
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <2150000>;
+ };
+
+ /*
+ * Some of the regulators are unused or managed by another
+ * processor (e.g. the modem). We should still define nodes for
+ * them to ensure the vote from the application processor can be
+ * dropped in case the regulators are already on during boot.
+ *
+ * The labels for these nodes are omitted on purpose because
+ * boards should configure a proper voltage before using them.
+ */
+ l1 {};
+
+ pm8916_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
/* pm8916_l3 is managed by rpmpd (MSM8916_VDDMX) */
- pm8916_l4: l4 {};
- pm8916_l5: l5 {};
- pm8916_l6: l6 {};
- pm8916_l7: l7 {};
- pm8916_l8: l8 {};
- pm8916_l9: l9 {};
- pm8916_l10: l10 {};
- pm8916_l11: l11 {};
- pm8916_l12: l12 {};
- pm8916_l13: l13 {};
- pm8916_l14: l14 {};
- pm8916_l15: l15 {};
- pm8916_l16: l16 {};
- pm8916_l17: l17 {};
- pm8916_l18: l18 {};
+
+ l4 {};
+
+ pm8916_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l8: l8 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8916_l9: l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l10 {};
+
+ pm8916_l11: l11 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
+
+ pm8916_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8916_l13: l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ l14 {};
+ l15 {};
+ l16 {};
+ l17 {};
+ l18 {};
};
};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
index b362a76eebc9..37a872949851 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
@@ -252,6 +252,13 @@ &pm8916_resin {
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&sdhc_1 {
status = "okay";
@@ -279,109 +286,6 @@ &usb_hs_phy {
extcon = <&muic>;
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
accel_int_default: accel-int-default-state {
pins = "gpio115";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
index 4464beeeaab1..a49e1641e59b 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
@@ -120,6 +120,13 @@ &pm8916_resin {
status = "okay";
};
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
/* FIXME: Replace with MAX77849 MUIC when driver is available */
&pm8916_usbin {
status = "okay";
@@ -162,109 +169,6 @@ &wcnss_iris {
compatible = "qcom,wcn3660b";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
accel_int_default: accel-int-default-state {
pins = "gpio115";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi
index 6e231e92e675..6192d04a58ae 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi
@@ -128,109 +128,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
gpio_hall_sensor_default: gpio-hall-sensor-default-state {
pins = "gpio52";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
index fa5b330aaeae..fc4c61c4e1e6 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
@@ -320,109 +320,6 @@ &wcnss_iris {
compatible = "qcom,wcn3660b";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
fg_alert_default: fg-alert-default-state {
pins = "gpio121";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
index b27896e83a0e..c8ea2f6f6b3d 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
@@ -126,109 +126,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
/* pins are board-specific */
button_default: button-default-state {
diff --git a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
index 78020a0db4e4..323590598113 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
@@ -149,6 +149,22 @@ &pm8916_resin {
linux,code = <KEY_VOLUMEDOWN>;
};
+&pm8916_rpm_regulators {
+ pm8916_l16: l16 {
+ /*
+ * L16 is only used for AW2013 which is fine with 2.5-3.3V.
+ * Use the recommended typical voltage of 2.8V as minimum.
+ */
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
&pm8916_vib {
status = "okay";
};
@@ -188,109 +204,6 @@ &wcnss_iris {
compatible = "qcom,wcn3620";
};
-&smd_rpm_regulators {
- vdd_l1_l2_l3-supply = <&pm8916_s3>;
- vdd_l4_l5_l6-supply = <&pm8916_s4>;
- vdd_l7-supply = <&pm8916_s4>;
-
- s3 {
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1350000>;
- };
-
- s4 {
- regulator-min-microvolt = <1850000>;
- regulator-max-microvolt = <2150000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l8 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- };
-
- l9 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l11 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l13 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l16 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-};
-
&msmgpio {
camera_flash_default: camera-flash-default-state {
pins = "gpio31", "gpio32";
--
2.40.1
