The geni_se_xx_dma_prep() interfaces necessarily do DMA mapping before
initiating DMA transfers. This is not suitable for spi where framework
is expected to handle map/unmap.
Expose new interfaces geni_se_xx_init_dma() which do only DMA transfer.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@xxxxxxxxxxx>
---
v1 -> v2:
- interfaces to take dma address as argument instead of its pointer
---
drivers/soc/qcom/qcom-geni-se.c | 67 +++++++++++++++++++++++++++++-----------
include/linux/soc/qcom/geni-se.h | 4 +++
2 files changed, 53 insertions(+), 18 deletions(-)
diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index 795a2e1..dd50a25 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -682,6 +682,30 @@ EXPORT_SYMBOL(geni_se_clk_freq_match);
#define GENI_SE_DMA_EOT_EN BIT(1)
#define GENI_SE_DMA_AHB_ERR_EN BIT(2)
#define GENI_SE_DMA_EOT_BUF BIT(0)
+
+/**
+ * geni_se_tx_init_dma() - Initiate TX DMA transfer on the serial engine
+ * @se: Pointer to the concerned serial engine.
+ * @iova: Mapped DMA address.
+ * @len: Length of the TX buffer.
+ *
+ * This function is used to initiate DMA TX transfer.
+ */
+void geni_se_tx_init_dma(struct geni_se *se, dma_addr_t iova, size_t len)
+{
+ u32 val;
+
+ val = GENI_SE_DMA_DONE_EN;
+ val |= GENI_SE_DMA_EOT_EN;
+ val |= GENI_SE_DMA_AHB_ERR_EN;
+ writel_relaxed(val, se->base + SE_DMA_TX_IRQ_EN_SET);
+ writel_relaxed(lower_32_bits(iova), se->base + SE_DMA_TX_PTR_L);
+ writel_relaxed(upper_32_bits(iova), se->base + SE_DMA_TX_PTR_H);
+ writel_relaxed(GENI_SE_DMA_EOT_BUF, se->base + SE_DMA_TX_ATTR);
+ writel(len, se->base + SE_DMA_TX_LEN);
+}
+EXPORT_SYMBOL(geni_se_tx_init_dma);
+
/**
* geni_se_tx_dma_prep() - Prepare the serial engine for TX DMA transfer
* @se: Pointer to the concerned serial engine.
@@ -697,7 +721,6 @@ int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
dma_addr_t *iova)
{
struct geni_wrapper *wrapper = se->wrapper;
- u32 val;
if (!wrapper)
return -EINVAL;
@@ -706,17 +729,34 @@ int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
if (dma_mapping_error(wrapper->dev, *iova))
return -EIO;
+ geni_se_tx_init_dma(se, *iova, len);
+ return 0;
+}
+EXPORT_SYMBOL(geni_se_tx_dma_prep);
+
+/**
+ * geni_se_rx_init_dma() - Initiate RX DMA transfer on the serial engine
+ * @se: Pointer to the concerned serial engine.
+ * @iova: Mapped DMA address.
+ * @len: Length of the RX buffer.
+ *
+ * This function is used to initiate DMA RX transfer.
+ */
+void geni_se_rx_init_dma(struct geni_se *se, dma_addr_t iova, size_t len)
+{
+ u32 val;
+
val = GENI_SE_DMA_DONE_EN;
val |= GENI_SE_DMA_EOT_EN;
val |= GENI_SE_DMA_AHB_ERR_EN;
- writel_relaxed(val, se->base + SE_DMA_TX_IRQ_EN_SET);
- writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_TX_PTR_L);
- writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_TX_PTR_H);
- writel_relaxed(GENI_SE_DMA_EOT_BUF, se->base + SE_DMA_TX_ATTR);
- writel(len, se->base + SE_DMA_TX_LEN);
- return 0;
+ writel_relaxed(val, se->base + SE_DMA_RX_IRQ_EN_SET);
+ writel_relaxed(lower_32_bits(iova), se->base + SE_DMA_RX_PTR_L);
+ writel_relaxed(upper_32_bits(iova), se->base + SE_DMA_RX_PTR_H);
+ /* RX does not have EOT buffer type bit. So just reset RX_ATTR */
+ writel_relaxed(0, se->base + SE_DMA_RX_ATTR);
+ writel(len, se->base + SE_DMA_RX_LEN);
}
-EXPORT_SYMBOL(geni_se_tx_dma_prep);
+EXPORT_SYMBOL(geni_se_rx_init_dma);
/**
* geni_se_rx_dma_prep() - Prepare the serial engine for RX DMA transfer
@@ -733,7 +773,6 @@ int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
dma_addr_t *iova)
{
struct geni_wrapper *wrapper = se->wrapper;
- u32 val;
if (!wrapper)
return -EINVAL;
@@ -742,15 +781,7 @@ int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
if (dma_mapping_error(wrapper->dev, *iova))
return -EIO;
- val = GENI_SE_DMA_DONE_EN;
- val |= GENI_SE_DMA_EOT_EN;
- val |= GENI_SE_DMA_AHB_ERR_EN;
- writel_relaxed(val, se->base + SE_DMA_RX_IRQ_EN_SET);
- writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_RX_PTR_L);
- writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_RX_PTR_H);
- /* RX does not have EOT buffer type bit. So just reset RX_ATTR */
- writel_relaxed(0, se->base + SE_DMA_RX_ATTR);
- writel(len, se->base + SE_DMA_RX_LEN);
+ geni_se_rx_init_dma(se, *iova, len);
return 0;
}
EXPORT_SYMBOL(geni_se_rx_dma_prep);
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index c55a0bc..821a191 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -490,9 +490,13 @@ int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
unsigned int *index, unsigned long *res_freq,
bool exact);
+void geni_se_tx_init_dma(struct geni_se *se, dma_addr_t iova, size_t len);
+
int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
dma_addr_t *iova);
+void geni_se_rx_init_dma(struct geni_se *se, dma_addr_t iova, size_t len);
+
int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
dma_addr_t *iova);
--
Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by the Linux Foundation.
