On 5/15/2023 7:56 PM, Johan Hovold wrote:
On Sun, May 14, 2023 at 11:19:15AM +0530, Krishna Kurapati wrote:
Add USB and DWC3 node for tertiary port of SC8280 along with multiport
IRQ's and phy's. This will be used as a base for SA8295P and SA8295-Ride
platforms.
Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 66 ++++++++++++++++++++++++++
1 file changed, 66 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index 8fa9fbfe5d00..50f6a8424537 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -3133,6 +3133,72 @@ usb_1_role_switch: endpoint {
};
};
+ usb_2: usb@a4f8800 {
As I believe someone already pointed out, this node is not in sort order
(i.e. it should go before usb@a6f8800).
Hi Johan,
I missed that message, but since I named it usb_2, so I placed it in
order after usb_1. Hope that is fine !!
+ compatible = "qcom,sc8280xp-dwc3-mp", "qcom,dwc3";
+ reg = <0 0x0a4f8800 0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
+ <&gcc GCC_USB30_MP_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
+ <&gcc GCC_USB30_MP_SLEEP_CLK>,
+ <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
+ <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+ <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
+ <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
+ <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+ "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+ assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_MP_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <200000000>;
+
+ interrupts-extended = <&pdc 127 IRQ_TYPE_EDGE_RISING>,
+ <&pdc 126 IRQ_TYPE_EDGE_RISING>,
+ <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 857 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 856 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-names = "dp_hs_phy_irq",
+ "dm_hs_phy_irq",
+ "ss_phy_irq",
+ "pwr_event_1",
+ "pwr_event_2",
+ "pwr_event_3",
+ "pwr_event_4";
+
+ power-domains = <&gcc USB30_MP_GDSC>;
+ required-opps = <&rpmhpd_opp_nom>;
+
+ resets = <&gcc GCC_USB30_MP_BCR>;
+
+ interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
This is not the correct interconnect master and slave; it should be
MASTER_USB3_MP and SLAVE_USB3_MP.
Thanks for pointing it out. I need to check how it was working all these
days. (Probably since both of them vote for the same NOC, it didn't show
any affect)
+ interconnect-names = "usb-ddr", "apps-usb";
Looks like 'wakeup-source' is missing here too.
I believe this property was added to enable wakeup from system suspend
in host mode. I didn't add this property as currently I don't need to
support wakeup. If any requirement comes in future, then I might need to
add dp/dm interrupts (if any) for other ports as well and then need to
change driver code to enable/disable them on suspend/resume.
+
+ status = "disabled";
+
+ usb_2_dwc3: usb@a400000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a400000 0 0xcd00>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x800 0x0>;
+ phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>,
+ <&usb_2_hsphy1>, <&usb_2_qmpphy1>,
+ <&usb_2_hsphy2>,
+ <&usb_2_hsphy3>;
+ phy-names = "usb2-port0", "usb3-port0",
+ "usb2-port1", "usb3-port1",
+ "usb2-port2",
+ "usb2-port3";
The phys and phy-names continuation lines above are still not aligned.
Missed it. Will fix it in next version.
Thanks,
Krishna,
+ };
+ };
+
mdss0: display-subsystem@ae00000 {
compatible = "qcom,sc8280xp-mdss";
reg = <0 0x0ae00000 0 0x1000>;
Johan
