Re: [PATCH v8 6/8] drm/msm/dpu: separate DSC flush update out of interface

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 5/12/2023 11:50 AM, Dmitry Baryshkov wrote:
On 12/05/2023 21:47, Abhinav Kumar wrote:


On 5/12/2023 11:21 AM, Dmitry Baryshkov wrote:
On 12/05/2023 21:00, Kuogee Hsieh wrote:
Current DSC flush update is piggyback inside dpu_hw_ctl_intf_cfg_v1().
This patch separates DSC flush away from dpu_hw_ctl_intf_cfg_v1() by
adding dpu_hw_ctl_update_pending_flush_dsc_v1() to handle both per
DSC engine and DSC flush bits at same time to make it consistent with
the location of flush programming of other dpu sub blocks.

Signed-off-by: Kuogee Hsieh <quic_khsieh@xxxxxxxxxxx>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 14 ++++++++++++--
  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c  | 22 ++++++++++++++++------
  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h  | 10 ++++++++++
  3 files changed, 38 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
index ffa6f04..5cae70e 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
@@ -1834,12 +1834,18 @@ dpu_encoder_dsc_initial_line_calc(struct drm_dsc_config *dsc,
      return DIV_ROUND_UP(total_pixels, dsc->slice_width);
  }
-static void dpu_encoder_dsc_pipe_cfg(struct dpu_hw_dsc *hw_dsc,
+static void dpu_encoder_dsc_pipe_cfg(struct dpu_encoder_virt *dpu_enc,
+                     struct dpu_hw_dsc *hw_dsc,
                       struct dpu_hw_pingpong *hw_pp,
                       struct drm_dsc_config *dsc,
                       u32 common_mode,
                       u32 initial_lines)
  {
+    struct dpu_encoder_phys *cur_master = dpu_enc->cur_master;
+    struct dpu_hw_ctl *ctl;
+
+    ctl = cur_master->hw_ctl;

Just for my understanding: if we have a bonded DSI @ sdm845, should both flashes go to the master CTL or each flush should go to the corresponding CTL?


Is this question for DSC or just general question about flush?

I dont see an explicit DSC flush needed in sdm845 at the ctl level.

If the question is about general flush involving two control paths, we need to combine the flushes and they goto the master only. Please refer to below part in sde_encoder.c
And this is because we have a single CTL to flush on sm8150+, isn't it?


For sm8150+, yes there will be only a single CTL to flush even in bonded DSI mode so only one will be flushed.

So, in general, you can refer to the function sde_encoder_phys_needs_single_flush() to decide if it needs 2 flushes or one. That accounts for the DPU rev as well.


4243     /* for split flush, combine pending flush masks and send to master */
4244     if (pending_flush.pending_flush_mask && sde_enc->cur_master) {
4245         ctl = sde_enc->cur_master->hw_ctl;
4246         if (config_changed && ctl->ops.reg_dma_flush)
4247             ctl->ops.reg_dma_flush(ctl, is_regdma_blocking);
4248         _sde_encoder_trigger_flush(&sde_enc->base, sde_enc->cur_master,
4249                         &pending_flush,
4250                         config_changed);
4251     }





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux