Re: [PATCH 4/6] ARM: dts: qcom: apq8074-dragonboard: add resin and gpio keys

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 8.05.2023 02:33, Dmitry Baryshkov wrote:
> Add device nodes for resin (reset, volume-down) and gpio-keys
> (volume-up, general key) device nodes.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
>  .../arm/boot/dts/qcom-apq8074-dragonboard.dts | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
> index 72f7e09a5bbf..2017bdf81677 100644
> --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
> +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
> @@ -1,5 +1,7 @@
>  // SPDX-License-Identifier: GPL-2.0
>  #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>  #include "qcom-msm8974.dtsi"
>  #include "qcom-pm8841.dtsi"
>  #include "qcom-pm8941.dtsi"
> @@ -20,6 +22,26 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		autorepeat;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&msm_keys_default>;
property-n
property-names
> +
> +		button-volup {
> +			label = "Volume Up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		button-general {
> +			label = "General";
> +			linux,code = <KEY_PROG1>;
> +			gpios = <&pm8941_gpios 23 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
>  	reserved-memory {
>  		mpss_region: mpss@ac00000 {
>  			reg = <0x0ac00000 0x2500000>;
> @@ -90,6 +112,25 @@ &mdss {
>  	status = "okay";
>  };
>  
> +&pm8941_gpios {
> +        msm_keys_default: pm8941-gpio-keys-state {
> +                pinconf {
unnecessary pinconf{} level

> +                        pins = "gpio5", "gpio23";
> +                        function = "normal";
> +                        input-enable;
> +                        drive-push-pull;
> +                        bias-pull-up;
> +                        qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> +                        power-source = <PM8941_GPIO_S3>; /* 1.8V */
> +                };
> +        };
> +};
> +
> +&pm8941_resin {
> +	status = "okay";
status last
> +	linux,code = <KEY_VOLUMEDOWN>;

Konrad
> +};
> +
>  &pm8941_wled {
>  	qcom,cs-out;
>  	qcom,switching-freq = <3200>;



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux