Re: [PATCH RFC 3/4] arm64: dts: qcom: sm6350: add uart1 node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Apr 21, 2023 at 9:12 AM Luca Weiss <luca.weiss@xxxxxxxxxxxxx> wrote:
>
> Add the node describing uart1 incl. opp table and pinctrl.
>
> Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sm6350.dtsi | 63 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 63 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index 18c4616848ce..16c5e9a6c98a 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -378,6 +378,25 @@ opp-2073600000 {
>                 };
>         };
>
> +       qup_opp_table: opp-table-qup {
> +               compatible = "operating-points-v2";
> +
> +               opp-75000000 {
> +                       opp-hz = /bits/ 64 <75000000>;
> +                       required-opps = <&rpmhpd_opp_low_svs>;
> +               };
> +
> +               opp-100000000 {
> +                       opp-hz = /bits/ 64 <100000000>;
> +                       required-opps = <&rpmhpd_opp_svs>;
> +               };
> +
> +               opp-128000000 {
> +                       opp-hz = /bits/ 64 <128000000>;
> +                       required-opps = <&rpmhpd_opp_nom>;
> +               };
> +       };
> +
>         pmu {
>                 compatible = "arm,armv8-pmuv3";
>                 interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_LOW>;
> @@ -741,6 +760,22 @@ i2c0: i2c@880000 {
>                                 status = "disabled";
>                         };
>
> +                       uart1: serial@884000 {
> +                               compatible = "qcom,geni-uart";
> +                               reg = <0 0x00884000 0 0x4000>;
> +                               clock-names = "se";
> +                               clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> +                               pinctrl-names = "default";
> +                               pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
> +                               interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
> +                               power-domains = <&rpmhpd SM6350_CX>;
> +                               operating-points-v2 = <&qup_opp_table>;
> +                               interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
> +                                               <&aggre1_noc MASTER_QUP_0 0 &clk_virt SLAVE_EBI_CH0 0>;
> +                               interconnect-names = "qup-core", "qup-config";
> +                               status = "disabled";
> +                       };
> +
>                         i2c2: i2c@888000 {
>                                 compatible = "qcom,geni-i2c";
>                                 reg = <0 0x00888000 0 0x4000>;
> @@ -1726,6 +1761,34 @@ qup_i2c10_default: qup-i2c10-default-state {
>                                 drive-strength = <2>;
>                                 bias-pull-up;
>                         };
> +
> +                       qup_uart1_cts: qup-uart1-cts-default-state {
> +                               pins = "gpio61";
> +                               function = "qup01";
> +                               drive-strength = <2>;
> +                               bias-disable;
> +                       };
> +
> +                       qup_uart1_rts: qup-uart1-rts-default-state {
> +                               pins = "gpio62";
> +                               function = "qup01";
> +                               drive-strength = <2>;
> +                               bias-pull-down;
> +                       };
> +
> +                       qup_uart1_tx: qup-uart1-tx-default-state {
> +                               pins = "gpio63";
> +                               function = "qup01";
> +                               drive-strength = <2>;
> +                               bias-pull-up;
> +                       };
> +
tx should come after the rx, this caught me too when I was doing my
bluetooth driver, it goes by name, not gpio#.

> +                       qup_uart1_rx: qup-uart1-rx-default-state {
> +                               pins = "gpio64";
> +                               function = "qup01";
> +                               drive-strength = <2>;
> +                               bias-disable;
> +                       };
>                 };
>
>                 apps_smmu: iommu@15000000 {
>
> --
> 2.40.0
>




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux