[PATCH 06/10] ARM: dts: qcom: ipq8064: correct LED node names

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



GPIO LEDs is not a bus, so drop unit-address and also start suffix
numbering from 0:

  Warning (unit_address_vs_reg): /soc/leds/led@7: node has a unit name, but no reg or ranges property

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts |  2 +-
 arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi  | 10 +++++-----
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
index 47a5d1849c72..52eadefd2fb4 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
@@ -203,7 +203,7 @@ leds {
 			pinctrl-0 = <&leds_pins>;
 			pinctrl-names = "default";
 
-			led@7 {
+			led-0 {
 				label = "rb3011:green:user";
 				color = <LED_COLOR_ID_GREEN>;
 				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
index 411c8d63c38e..c5abe7151f14 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
@@ -92,34 +92,34 @@ leds {
 			pinctrl-0 = <&leds_pins>;
 			pinctrl-names = "default";
 
-			led@7 {
+			led-0 {
 				label = "led_usb1";
 				gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
 				linux,default-trigger = "usbdev";
 				default-state = "off";
 			};
 
-			led@8 {
+			led-1 {
 				label = "led_usb3";
 				gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
 				linux,default-trigger = "usbdev";
 				default-state = "off";
 			};
 
-			led@9 {
+			led-2 {
 				label = "status_led_fail";
 				function = LED_FUNCTION_STATUS;
 				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
 				default-state = "off";
 			};
 
-			led@26 {
+			led-3 {
 				label = "sata_led";
 				gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
 				default-state = "off";
 			};
 
-			led@53 {
+			led-4 {
 				label = "status_led_pass";
 				function = LED_FUNCTION_STATUS;
 				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
-- 
2.34.1




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux