On 3/30/2023 5:16 PM, Dmitry Baryshkov wrote:
On Fri, 31 Mar 2023 at 03:07, Jessica Zhang <quic_jesszhan@xxxxxxxxxxx> wrote:
On 3/30/2023 4:14 PM, Dmitry Baryshkov wrote:
On 31/03/2023 01:49, Jessica Zhang wrote:
On 3/29/2023 4:48 PM, Dmitry Baryshkov wrote:
On 30/03/2023 02:18, Jessica Zhang wrote:
Use MSM and DRM DSC helper methods.
Signed-off-by: Jessica Zhang <quic_jesszhan@xxxxxxxxxxx>
---
drivers/gpu/drm/msm/dsi/dsi_host.c | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c
b/drivers/gpu/drm/msm/dsi/dsi_host.c
index 74d38f90398a..7419fe58a941 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -31,6 +31,7 @@
#include "msm_kms.h"
#include "msm_gem.h"
#include "phy/dsi_phy.h"
+#include "disp/msm_dsc_helper.h"
#define DSI_RESET_TOGGLE_DELAY_MS 20
@@ -841,14 +842,14 @@ static void dsi_update_dsc_timing(struct
msm_dsi_host *msm_host, bool is_cmd_mod
{
struct drm_dsc_config *dsc = msm_host->dsc;
u32 reg, reg_ctrl, reg_ctrl2;
- u32 slice_per_intf, total_bytes_per_intf;
+ u32 slice_per_intf;
u32 pkt_per_line;
u32 eol_byte_num;
/* first calculate dsc parameters and then program
* compress mode registers
*/
- slice_per_intf = DIV_ROUND_UP(hdisplay, dsc->slice_width);
+ slice_per_intf = msm_dsc_get_slice_per_intf(dsc, hdisplay);
This looks good
/*
* If slice_count is greater than slice_per_intf
@@ -858,10 +859,10 @@ static void dsi_update_dsc_timing(struct
msm_dsi_host *msm_host, bool is_cmd_mod
if (dsc->slice_count > slice_per_intf)
dsc->slice_count = 1;
- total_bytes_per_intf = dsc->slice_chunk_size * slice_per_intf;
+ eol_byte_num = msm_dsc_get_eol_byte_num(msm_host->dsc, hdisplay,
+ dsi_get_bpp(msm_host->format));
- eol_byte_num = total_bytes_per_intf % 3;
- pkt_per_line = slice_per_intf / dsc->slice_count;
+ pkt_per_line = slice_per_intf / MSM_DSC_SLICE_PER_PKT;
And for these values the result is definitely changed. Separate patch
& description please. Just in case, "values per downstream kernel" is
not a proper description for such changes.
Hi Dmitry,
Sure, I can put this into a separate patch.
The reason this was changed from slice_count to SLICE_PER_PKT was
because slice count and slice per packet aren't always equivalent.
There can be cases where panel configures DSC to have multiple soft
slices per interface, but the panel only specifies 1 slice per packet.
Please put this nice description into the commit message. It is exactly
what I was looking for!
BTW: Do you expect to change MSM_DSC_SLICE_PER_PKT later or it will stay
at "1"? If so, it might be easier to drop it and instead add a comment.
MSM_DSC_SLICE_PER_PKT is the default value for panels that don't specify
a slice_per_pkt value. (Now that I think about it, might be better to
call it MSM_DSC_DEFAULT_SLICE_PER_PKT instead...)
Note, there is no slice_per_pkt in drm_dsc_config, so we must come up
with another way to pass this data from the panel or to deduce the
value in our driver.
I don't expect it to change in the future, but it's a little more
readable than just dividing by 1 IMO. If you prefer dropping the macro
and adding a comment, I'm also okay with that.
There is no need to divide by 1, the value doesn't change. So I'd
probably prefer something like:
/* Default to 1 slice per packet */
if (panel_slice_per_pkt)
pkt_per_line = slice_per_intf / panel_slice_per_pkt;
else
pkt_per_line = slice_per_intf;
Or:
/* Default to 1 slice per packet */
slice_per_pkt = 1;
if (panel_slice_per_pkt)
slice_per_pkt = panel_slice_per_pkt;
pkt_per_line = slice_per_intf / slice_per_pkt;
BTW: could you possibly change 'intf' to 'line' to v2? It seems there
is a mixture of them through the code. If there is a difference
between intf and line which is not yet posted, it's fine to keep the
current code. WDYT?
No, I dont agree with the change from intf to line.
In case of dual DSI, intf is not equal to line.
2 intfs = 1 line
Hence that distinction is necessary.
Thanks,
Jessica Zhang
Regarding eol_byte_num, probably the best explanation would be that is
is a size of a padding rather than a size of a trailer bytes in a line
(and thus original calculation was incorrect).
if (is_cmd_mode) /* packet data type */
reg =
DSI_COMMAND_COMPRESSION_MODE_CTRL_STREAM0_DATATYPE(MIPI_DSI_DCS_LONG_WRITE);
@@ -911,6 +912,11 @@ static void dsi_timing_setup(struct
msm_dsi_host *msm_host, bool is_bonded_dsi)
DBG("");
+ if (msm_host->mode_flags & MIPI_DSI_MODE_VIDEO)
+ /* Default widebus_en to false for now. */
+ hdisplay = msm_dsc_get_pclk_per_line(msm_host->dsc,
mode->hdisplay,
+ dsi_get_bpp(msm_host->format));
+
This is definitely something new and thus should probably go into a
separate patch and be described. Also I'm not sure how does that
interact with the hdisplay-related calculations below, under the
if(dsc) clause.
After double-checking the math here, I think this part of the change
is actually wrong. pclk_per_line is essentially doing hdisplay / 3,
which is a repeat of what's being done in the `if (dsc)` block.
Will replace `hdisplay /= 3` with the pclk_per_line calculation.
Thanks!
Thanks,
Jessica Zhang
/*
* For bonded DSI mode, the current DRM mode has
* the complete width of the panel. Since, the complete
@@ -1759,7 +1765,7 @@ static int dsi_populate_dsc_params(struct
msm_dsi_host *msm_host, struct drm_dsc
return ret;
}
- dsc->initial_scale_value = 32;
+ dsc->initial_scale_value =
drm_dsc_calculate_initial_scale_value(dsc);
This is fine, we only support 8bpp where these values match.
dsc->line_buf_depth = dsc->bits_per_component + 1;
return drm_dsc_compute_rc_parameters(dsc);
--
With best wishes
Dmitry
--
With best wishes
Dmitry
