On 26.03.2023 11:16, Krzysztof Kozlowski wrote:
> The soc node is supposed to have only device nodes with MMIO addresses,
> so move the DSI OPP out of it (it is used also by second DSI1 on
> SDM660):
>
> sda660-inforce-ifc6560.dtb: soc: opp-table-dsi: {'compatible': ['operating-points-v2'], ... should not be valid under {'type': 'object'}
> From schema: dtschema/schemas/simple-bus.yaml
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Konrad
>
> Changes since v1:
> 1. Move the node out of soc. Don't add Konrad's review tag.
> ---
> arch/arm64/boot/dts/qcom/sdm630.dtsi | 38 ++++++++++++++--------------
> 1 file changed, 19 insertions(+), 19 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
> index 72d9a12b5e9c..b91e423a3cfc 100644
> --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
> @@ -328,6 +328,25 @@ memory@80000000 {
> reg = <0x0 0x80000000 0x0 0x0>;
> };
>
> + dsi_opp_table: opp-table-dsi {
> + compatible = "operating-points-v2";
> +
> + opp-131250000 {
> + opp-hz = /bits/ 64 <131250000>;
> + required-opps = <&rpmpd_opp_svs>;
> + };
> +
> + opp-210000000 {
> + opp-hz = /bits/ 64 <210000000>;
> + required-opps = <&rpmpd_opp_svs_plus>;
> + };
> +
> + opp-262500000 {
> + opp-hz = /bits/ 64 <262500000>;
> + required-opps = <&rpmpd_opp_nom>;
> + };
> + };
> +
> pmu {
> compatible = "arm,armv8-pmuv3";
> interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
> @@ -1450,25 +1469,6 @@ mmcc: clock-controller@c8c0000 {
> <0>;
> };
>
> - dsi_opp_table: opp-table-dsi {
> - compatible = "operating-points-v2";
> -
> - opp-131250000 {
> - opp-hz = /bits/ 64 <131250000>;
> - required-opps = <&rpmpd_opp_svs>;
> - };
> -
> - opp-210000000 {
> - opp-hz = /bits/ 64 <210000000>;
> - required-opps = <&rpmpd_opp_svs_plus>;
> - };
> -
> - opp-262500000 {
> - opp-hz = /bits/ 64 <262500000>;
> - required-opps = <&rpmpd_opp_nom>;
> - };
> - };
> -
> mdss: display-subsystem@c900000 {
> compatible = "qcom,mdss";
> reg = <0x0c900000 0x1000>,
