On 24.03.2023 21:15, Alex Elder wrote:
> Move a few device tree "status" properties so that they are the last
> specified property, in "qcom-sdx65-mtp.dts" and "qcom-sdx65.dtsi".
> Note that properties must always be specified before sub-nodes.
>
> Suggested-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
> Signed-off-by: Alex Elder <elder@xxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Konrad
> arch/arm/boot/dts/qcom-sdx65-mtp.dts | 6 +++---
> arch/arm/boot/dts/qcom-sdx65.dtsi | 8 +++++---
> 2 files changed, 8 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> index 72e25de0db5fc..57bc3b03d3aac 100644
> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> @@ -270,8 +270,8 @@ nand@0 {
> };
>
> &remoteproc_mpss {
> - status = "okay";
> memory-region = <&mpss_adsp_mem>;
> + status = "okay";
> };
>
> &usb {
> @@ -283,14 +283,14 @@ &usb_dwc3 {
> };
>
> &usb_hsphy {
> - status = "okay";
> vdda-pll-supply = <&vreg_l4b_0p88>;
> vdda33-supply = <&vreg_l10b_3p08>;
> vdda18-supply = <&vreg_l5b_1p8>;
> + status = "okay";
> };
>
> &usb_qmpphy {
> - status = "okay";
> vdda-phy-supply = <&vreg_l4b_0p88>;
> vdda-pll-supply = <&vreg_l1b_1p2>;
> + status = "okay";
> };
> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
> index 360d6dc144811..a7adf28a395a8 100644
> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
> @@ -224,16 +224,15 @@ usb_hsphy: phy@ff4000 {
> "qcom,usb-snps-hs-7nm-phy";
> reg = <0xff4000 0x120>;
> #phy-cells = <0>;
> - status = "disabled";
> clocks = <&rpmhcc RPMH_CXO_CLK>;
> clock-names = "ref";
> resets = <&gcc GCC_QUSB2PHY_BCR>;
> + status = "disabled";
> };
>
> usb_qmpphy: phy@ff6000 {
> compatible = "qcom,sdx65-qmp-usb3-uni-phy";
> reg = <0x00ff6000 0x1c8>;
> - status = "disabled";
> #address-cells = <1>;
> #size-cells = <1>;
> ranges;
> @@ -247,6 +246,8 @@ usb_qmpphy: phy@ff6000 {
> <&gcc GCC_USB3_PHY_BCR>;
> reset-names = "phy", "common";
>
> + status = "disabled";
> +
> usb_ssphy: phy@ff6200 {
> reg = <0x00ff6e00 0x160>,
> <0x00ff7000 0x1ec>,
> @@ -393,7 +394,6 @@ mem_noc: interconnect@9680000 {
> usb: usb@a6f8800 {
> compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
> reg = <0x0a6f8800 0x400>;
> - status = "disabled";
> #address-cells = <1>;
> #size-cells = <1>;
> ranges;
> @@ -423,6 +423,8 @@ usb: usb@a6f8800 {
>
> resets = <&gcc GCC_USB30_BCR>;
>
> + status = "disabled";
> +
> usb_dwc3: usb@a600000 {
> compatible = "snps,dwc3";
> reg = <0x0a600000 0xcd00>;
