Re: [net-next PATCH v5 10/15] dt-bindings: net: ethernet-controller: Document support for LEDs node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Mar 21, 2023 at 11:54:46PM +0100, Christian Marangi wrote:
> On Tue, Mar 21, 2023 at 04:19:53PM -0500, Rob Herring wrote:
> > On Sun, Mar 19, 2023 at 08:18:09PM +0100, Christian Marangi wrote:
> > > Document support for LEDs node in ethernet-controller.
> > > Ethernet Controller may support different LEDs that can be configured
> > > for different operation like blinking on traffic event or port link.
> > > 
> > > Also add some Documentation to describe the difference of these nodes
> > > compared to PHY LEDs, since ethernet-controller LEDs are controllable
> > > by the ethernet controller regs and the possible intergated PHY doesn't
> > > have control on them.
> > > 
> > > Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> > > ---
> > >  .../bindings/net/ethernet-controller.yaml     | 21 +++++++++++++++++++
> > >  1 file changed, 21 insertions(+)
> > > 
> > > diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml
> > > index 00be387984ac..a93673592314 100644
> > > --- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml
> > > +++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml
> > > @@ -222,6 +222,27 @@ properties:
> > >          required:
> > >            - speed
> > >  
> > > +  leds:
> > > +    type: object
> > > +    description:
> > > +      Describes the LEDs associated by Ethernet Controller.
> > > +      These LEDs are not integrated in the PHY and PHY doesn't have any
> > > +      control on them. Ethernet Controller regs are used to control
> > > +      these defined LEDs.
> > > +
> > > +    properties:
> > > +      '#address-cells':
> > > +        const: 1
> > > +
> > > +      '#size-cells':
> > > +        const: 0
> > > +
> > > +    patternProperties:
> > > +      '^led(@[a-f0-9]+)?$':
> > > +        $ref: /schemas/leds/common.yaml#
> > 
> > Are specific ethernet controllers allowed to add their own properties in 
> > led nodes? If so, this doesn't work. As-is, this allows any other 
> > properties. You need 'unevaluatedProperties: false' here to prevent 
> > that. But then no one can add properties. If you want to support that, 
> > then you need this to be a separate schema that devices can optionally 
> > include if they don't extend the properties, and then devices that 
> > extend the binding would essentially have the above with:
> > 
> > $ref: /schemas/leds/common.yaml#
> > unevaluatedProperties: false
> > properties:
> >   a-custom-device-prop: ...
> > 
> > 
> > If you wanted to define both common ethernet LED properties and 
> > device specific properties, then you'd need to replace leds/common.yaml 
> > above  with the ethernet one.
> > 
> > This is all the same reasons the DSA/switch stuff and graph bindings are 
> > structured the way they are.
> > 
> 
> Hi Rob, thanks for the review/questions.
> 
> The idea of all of this is to keep leds node as standard as possible.
> It was asked to add unevaluatedProperties: False but I didn't understood
> it was needed also for the led nodes.
> 
> leds/common.yaml have additionalProperties set to true but I guess that
> is not OK for the final schema and we need something more specific.

Yes, every node needs a schema with all possible properties and then 
'unevaluatedProperties: false' to not allow any other properties.

> Looking at the common.yaml schema reg binding is missing so an
> additional schema is needed.
> 
> Reg is needed for ethernet LEDs and PHY but I think we should also permit
> to skip that if the device actually have just one LED. (if this wouldn't
> complicate the implementation. Maybe some hints from Andrew about this
> decision?)
> 
> If we decide that reg is a must, if I understood it correctly we should
> create something like leds-ethernet.yaml that would reference common and
> add reg binding? Is it correct? This schema should be laded in leds
> directory and not in the net/ethernet.

You need 'reg' in properties, but whether it is required or not just 
depends on putting it in 'required'. I don't have a strong opinion on 
that, but generally it's only use 'reg' when there's more than 1.

Rob



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux