Change the USB QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 31 +++++++++++----------------
1 file changed, 12 insertions(+), 19 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 9ff4e9d45065..ff540bfcc062 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -220,31 +220,24 @@ qusb_phy_1: qusb@59000 {
ssphy_0: ssphy@78000 {
compatible = "qcom,ipq6018-qmp-usb3-phy";
- reg = <0x0 0x00078000 0x0 0x1c4>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
+ reg = <0x0 0x00078000 0x0 0x1000>;
clocks = <&gcc GCC_USB0_AUX_CLK>,
- <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>;
- clock-names = "aux", "cfg_ahb", "ref";
+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&xo>,
+ <&gcc GCC_USB0_PIPE_CLK>;
+ clock-names = "aux",
+ "cfg_ahb",
+ "ref",
+ "pipe";
+ clock-output-names = "gcc_usb0_pipe_clk_src";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
resets = <&gcc GCC_USB0_PHY_BCR>,
<&gcc GCC_USB3PHY_0_PHY_BCR>;
reset-names = "phy","common";
status = "disabled";
-
- usb0_ssphy: phy@78200 {
- reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
- <0x0 0x00078400 0x0 0x200>, /* Rx */
- <0x0 0x00078800 0x0 0x1f8>, /* PCS */
- <0x0 0x00078600 0x0 0x044>; /* PCS misc */
- #phy-cells = <0>;
- #clock-cells = <0>;
- clocks = <&gcc GCC_USB0_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "gcc_usb0_pipe_clk_src";
- };
};
qusb_phy_0: qusb@79000 {
@@ -553,7 +546,7 @@ dwc_0: usb@8a00000 {
compatible = "snps,dwc3";
reg = <0x0 0x08a00000 0x0 0xcd00>;
interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&qusb_phy_0>, <&usb0_ssphy>;
+ phys = <&qusb_phy_0>, <&ssphy_0>;
phy-names = "usb2-phy", "usb3-phy";
clocks = <&xo>;
clock-names = "ref";
--
2.30.2
