[PATCH v2 2/4] arm64: dts: qcom: sm8250-xiaomi-elish: Add mdss and dsi node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



xiaomi-elish uses dual dsi mode panel and dsi phy type is cphy.

Signed-off-by: Jianhua Lu <lujianhua000@xxxxxxxxx>
---
Changes in v2:
  - Include missing <dt-bindings/phy/phy.h> for phy-type property.

 .../dts/qcom/sm8250-xiaomi-elish-common.dtsi  | 73 +++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish-common.dtsi b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish-common.dtsi
index a43d4b73ffca..4ff8454d4abe 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish-common.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/arm/qcom,ids.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/phy/phy.h>
 #include "sm8250.dtsi"
 #include "pm8150.dtsi"
 #include "pm8150b.dtsi"
@@ -469,6 +470,74 @@ &cdsp {
 	status = "okay";
 };
 
+&dsi0 {
+	vdda-supply = <&vreg_l9a_1p2>;
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+	qcom,sync-dual-dsi;
+	status = "okay";
+
+	display_panel: panel@0 {
+		reg = <0>;
+		vddio-supply = <&vreg_l14a_1p88>;
+		reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				panel_in_0: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1{
+				reg = <1>;
+				panel_in_1: endpoint {
+					remote-endpoint = <&dsi1_out>;
+				};
+			};
+
+		};
+	};
+};
+
+&dsi0_out {
+	data-lanes = <0 1 2>;
+	remote-endpoint = <&panel_in_0>;
+};
+
+&dsi0_phy {
+	vdds-supply = <&vreg_l5a_0p88>;
+	phy-type = <PHY_TYPE_CPHY>;
+	status = "okay";
+};
+
+&dsi1 {
+	vdda-supply = <&vreg_l9a_1p2>;
+	qcom,dual-dsi-mode;
+	qcom,sync-dual-dsi;
+	/* DSI1 is slave, so use DSI0 clocks */
+	assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
+	status = "okay";
+};
+
+&dsi1_out {
+	data-lanes = <0 1 2>;
+	remote-endpoint = <&panel_in_1>;
+};
+
+&dsi1_phy {
+	vdds-supply = <&vreg_l5a_0p88>;
+	phy-type = <PHY_TYPE_CPHY>;
+	status = "okay";
+};
+
 &gmu {
 	status = "okay";
 };
@@ -533,6 +602,10 @@ fuel-gauge@55 {
 	};
 };
 
+&mdss {
+	status = "okay";
+};
+
 &pcie0 {
 	status = "okay";
 };
-- 
2.39.2




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux