First things first, I do not have access to the specs nor the schematics, so a
lot of this was done via guess work, looking at the acpi tables, and looking at
how a similar device (wcn6750) was added.
The end result is that we do have a working device, using the firmware files
that are found in the linux-firmware git repository already.
Bluetooth: hci0: setting up wcn6855
Bluetooth: hci0: Frame reassembly failed (-84)
Bluetooth: hci0: QCA Product ID :0x00000013
Bluetooth: hci0: QCA SOC Version :0x400c0210
Bluetooth: hci0: QCA ROM Version :0x00000201
Bluetooth: hci0: QCA Patch Version:0x000038e6
Bluetooth: hci0: QCA controller version 0x02100201
Bluetooth: hci0: QCA Downloading qca/hpbtfw21.tlv
Bluetooth: hci0: QCA Downloading qca/hpnv21.bin
Bluetooth: hci0: QCA setup on UART is completed
There are a few things that I am not sure why they happen, and don't have the
knowledge level to figure out why they happen or debugging it.
I do not know why the Frame assembly failed, and modprobe -r hci_uart and then
modprobe hci_uart does not always show the same Frame assembly failed.
The BD Address also seems to be incorrect, and I'm not sure what is going on
there either.
Testing was done by connecting a Razer Orochi bluetooth mouse, and using it, as
well as connecting to and using an H2GO bluetooth speaker and playing audio out
via canberra-gtk-play as well as a couple of YouTube videos in a browser.
Additionally, a huddle was done in Slack on Chromium with a pair of Gen1 Apple
AirPods as well as a hangout in Discord on Firefox ESR.
steev@wintermute:~$ hciconfig -a
hci0: Type: Primary Bus: UART
BD Address: 00:00:00:00:5A:AD ACL MTU: 1024:8 SCO MTU: 240:4
UP RUNNING PSCAN
RX bytes:1492 acl:0 sco:0 events:126 errors:0
TX bytes:128743 acl:0 sco:0 commands:597 errors:0
Features: 0xff 0xfe 0x8f 0xfe 0xd8 0x3f 0x5b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF
Link mode: PERIPHERAL ACCEPT
Name: 'wintermute'
Class: 0x0c010c
Service Classes: Rendering, Capturing
Device Class: Computer, Laptop
HCI Version: (0xc) Revision: 0x0
LMP Version: (0xc) Subversion: 0x46f7
Manufacturer: Qualcomm (29)
steev@wintermute:~$ dmesg | grep Razer
[ 3089.235440] input: Razer Orochi as /devices/virtual/misc/uhid/0005:1532:0056.0003/input/input11
[ 3089.238580] hid-generic 0005:1532:0056.0003: input,hidraw2: BLUETOOTH HID v0.01 Mouse [Razer Orochi] on 00:00:00:00:5a:ad
steev@wintermute:~$ dmesg | grep H2GO
[ 3140.959947] input: H2GO Speaker (AVRCP) as /devices/virtual/input/input12
steev@wintermute:~$ dmesg | grep AirPod
[ 853.742619] input: Steev’s AirPods (AVRCP) as /devices/virtual/input/input14
v7 Addresses commit message review nits by Paul, as well as dts
changes requested by Johan. Additionally, the dt bindings now rely on
https://lore.kernel.org/lkml/20230316105800.18751-1-johan+linaro@xxxxxxxxxx/ for
the bias-bus-hold option on sc8280xp.
v6 can be found at https://lore.kernel.org/all/20230316034759.73489-1-steev@xxxxxxxx/
Bjorn Andersson (1):
arm64: dts: qcom: sc8280xp: Define uart2
Steev Klimaszewski (3):
dt-bindings: net: Add WCN6855 Bluetooth
Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855
arm64: dts: qcom: sc8280xp-x13s: Add bluetooth
.../net/bluetooth/qualcomm-bluetooth.yaml | 17 ++++
.../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 78 +++++++++++++++++++
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 14 ++++
drivers/bluetooth/btqca.c | 14 +++-
drivers/bluetooth/btqca.h | 10 +++
drivers/bluetooth/hci_qca.c | 57 ++++++++++----
6 files changed, 175 insertions(+), 15 deletions(-)
--
2.39.2
