On 21 March 2023 11:54:25 GMT+03:00, Varadarajan Narayanan <quic_varada@xxxxxxxxxxx> wrote:
>Add USB phy and controller related nodes
>
>Signed-off-by: Varadarajan Narayanan <quic_varada@xxxxxxxxxxx>
>
>---
> Changes in v2:
> - Fixed issues flagged by Krzysztof
> - Fix issues reported by make dtbs_check
> - Remove NOC related clocks (to be added with proper
> interconnect support)
>---
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 86 +++++++++++++++++++++++++++++++++++
> 1 file changed, 86 insertions(+)
>
>diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>index 2bb4053..513da74 100644
>--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>@@ -829,6 +829,92 @@
> msi-parent = <&v2m0>;
> status = "disabled";
> };
The last device node is pci@28000000. Thus you are trying to add all usb nodes at the wrong place. Please move them so that all nodes are still sorted by the address part.
>+
>+ qusb_phy_0: phy@7b000 {
>+ compatible = "qcom,ipq9574-qusb2-phy";
>+ reg = <0x07b000 0x180>;
>+ #phy-cells = <0>;
>+
>+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
>+ <&xo_board_clk>;
>+ clock-names = "cfg_ahb", "ref";
>+
>+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
>+ status = "disabled";
>+ };
>+
>+ ssphy_0: phy@7d000 {
>+ compatible = "qcom,ipq9574-qmp-usb3-phy";
>+ reg = <0x7d000 0x1c4>;
>+ #clock-cells = <1>;
>+ #address-cells = <1>;
>+ #size-cells = <1>;
>+ ranges;
>+
>+ clocks = <&gcc GCC_USB0_AUX_CLK>,
>+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;
>+ clock-names = "aux", "cfg_ahb";
>+
>+ resets = <&gcc GCC_USB0_PHY_BCR>,
>+ <&gcc GCC_USB3PHY_0_PHY_BCR>;
>+ reset-names = "phy","common";
>+ status = "disabled";
>+
>+ usb0_ssphy: phy@7d200 {
>+ reg = <0x0007d200 0x130>, /* tx */
>+ <0x0007d400 0x200>, /* rx */
>+ <0x0007d800 0x1f8>, /* pcs */
>+ <0x0007d600 0x044>; /* pcs misc */
>+ #phy-cells = <0>;
>+ clocks = <&gcc GCC_USB0_PIPE_CLK>;
>+ clock-names = "pipe0";
>+ clock-output-names = "usb0_pipe_clk";
>+ };
>+ };
>+
>+ usb3: usb3@8a00000 {
>+ compatible = "qcom,ipq9574-dwc3", "qcom,dwc3";
>+ reg = <0x8af8800 0x400>;
>+ #address-cells = <1>;
>+ #size-cells = <1>;
>+ ranges;
>+
>+ clocks = <&gcc GCC_SNOC_USB_CLK>,
>+ <&gcc GCC_ANOC_USB_AXI_CLK>,
>+ <&gcc GCC_USB0_MASTER_CLK>,
>+ <&gcc GCC_USB0_SLEEP_CLK>,
>+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
>+
>+ clock-names = "sys_noc_axi",
>+ "anoc_axi",
>+ "master",
>+ "sleep",
>+ "mock_utmi";
>+
>+ assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>,
>+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
>+ assigned-clock-rates = <200000000>,
>+ <24000000>;
>+
>+ resets = <&gcc GCC_USB_BCR>;
>+ status = "disabled";
>+
>+ dwc_0: usb@8a00000 {
>+ compatible = "snps,dwc3";
>+ reg = <0x8a00000 0xcd00>;
>+ clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
>+ clock-names = "ref";
>+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
>+ phys = <&qusb_phy_0>, <&usb0_ssphy>;
>+ phy-names = "usb2-phy", "usb3-phy";
>+ tx-fifo-resize;
>+ snps,is-utmi-l1-suspend;
>+ snps,hird-threshold = /bits/ 8 <0x0>;
>+ snps,dis_u2_susphy_quirk;
>+ snps,dis_u3_susphy_quirk;
>+ dr_mode = "host";
>+ };
>+ };
> };
>
> rpm-glink {
--
With best wishes
Dmitry
