On 20.03.2023 16:48, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
>
> Add the thermal zones and associated alarm nodes for the PMICs that have
> them hooked up on sa8775p-ride.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 58 +++++++++++++++++++++
> 1 file changed, 58 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> index 8616ead3daf5..276070b62ccd 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> @@ -6,6 +6,50 @@
> #include <dt-bindings/input/input.h>
> #include <dt-bindings/spmi/spmi.h>
>
> +/ {
> + thermal-zones {
> + pmm8654au_1_thermal: pm8775-1-thermal {
Please reindex this, downstream uses _1 for pmic@0, but this
makes little sense. Make it match the SID.
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> + thermal-sensors = <&pmm8654au_1_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <105000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <125000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> +
What happened to the downstream _2 (pmic@2) one and _4 (pmic@6)?
Konrad
> + pmm8654au_3_thermal: pm8775-3-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> + thermal-sensors = <&pmm8654au_3_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <105000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <125000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +};
> +
> &spmi_bus {
> pmm8654au_0: pmic@0 {
> compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
> @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 {
> reg = <0x2 SPMI_USID>;
> #address-cells = <1>;
> #size-cells = <0>;
> +
> + pmm8654au_1_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> };
>
> pmm8654au_2: pmic@4 {
> @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 {
> reg = <0x6 SPMI_USID>;
> #address-cells = <1>;
> #size-cells = <0>;
> +
> + pmm8654au_3_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> };
> };
