[PATCH 2/2] arm64: dts: qcom: Add Acer Aspire 1

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform.

The laptop design is similar to trogdor in the choice of primary
components but the specifics on usage of those differ slightly.

Add the devicetree for the laptop with support for most of the
hardware present.

Signed-off-by: Nikita Travkin <nikita@xxxxxxx>
---

Notable features absent from this patch:
- Sound
    While the dedicated sound components are defined, since the
    ADSP must be used, sound requires additions of that remoteproc
    as well some extra "glue" to connect the i2s outputs to it.
    I was able to hack together some sound based on sm8250 stuff
    but it needs more work.
- Embedded Controller
    The laptop has a dedicated EC that controls, notably,
    battery/charger and notifies the device about the USB-C DisplayPort
    HPD events. As per this patch, there is no battery status
    indication and external display support. Also, due to the EC
    defaults, the fn key is disabled. I have an experimental driver that
    implements all of that, which needs more work and will be submitted
    at a later date.
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sc7180-acer-aspire1.dts     | 867 ++++++++++++++++++
 2 files changed, 868 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 31aa54f0428c..8f0ffe35ca92 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -75,6 +75,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qru1000-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-acer-aspire1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts b/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts
new file mode 100644
index 000000000000..2cd7c63d16f1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts
@@ -0,0 +1,867 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc7180.dtsi"
+
+#include "pm6150.dtsi"
+#include "pm6150l.dtsi"
+
+/delete-node/ &tz_mem;
+/delete-node/ &ipa_fw_mem;
+
+/ {
+	model = "Acer Aspire 1";
+	compatible = "acer,aspire1", "qcom,sc7180";
+	chassis-type = "laptop";
+
+	reserved-memory {
+		zap_mem: zap-shader@80840000 {
+			reg = <0 0x80840000 0 0x2000>;
+			no-map;
+		};
+
+		venus_mem: venus@85b00000 {
+			reg = <0 0x85b00000 0 0x500000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@86000000 {
+			reg = <0x0 0x86000000 0x0 0x2000000>;
+			no-map;
+		};
+
+		adsp_mem: adsp@8e400000 {
+			reg = <0x0 0x8e400000 0x0 0x2800000>;
+			no-map;
+		};
+
+		wlan_mem: wlan@93900000 {
+			reg = <0x0 0x93900000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		bluetooth0 = &bluetooth;
+		hsuart0 = &uart3;
+		serial0 = &uart8;
+		wifi0 = &wifi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	max98357a: audio-codec-0 {
+		compatible = "maxim,max98357a";
+		sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&amp_sd_mode_default>;
+		pinctrl-names = "default";
+
+		#sound-dai-cells = <0>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&sn65dsi86_bridge 1000000>;
+		enable-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&soc_bkoff_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_brij_1p2: bridge-1p2-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "brij_1p2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_edp_1p2_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_brij_1p8: bridge-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "brij_1p8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		vin-supply = <&vreg_l8c_1p8>;
+
+		gpio = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_edp_1p8_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_codec_3p3: codec-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "codec_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_audio_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_lcm_3p3: panel-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "lcm_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		/* HACK: Display fails with
+		 *
+		 * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz
+		 * *ERROR* Link training failed, link is off (-5)
+		 *
+		 * if the power to the panel was ever cut
+		 */
+		regulator-always-on;
+
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_lcm_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_tp_3p3: touchpad-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "tp_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&reg_tp_en_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&camcc { status = "disabled"; };
+
+&dsi0 {
+	vdda-supply = <&vreg_l3c_1p2>;
+	status = "okay";
+};
+
+&dsi0_out {
+	remote-endpoint = <&sn65dsi86_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi_phy {
+	vdds-supply = <&vreg_l4a_0p8>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* embedded-controller@76 */
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/*
+	 * NOTE: DSDT defines two possible touchpads, other one is
+	 *
+	 * reg = <0x15>;
+	 * hid-descr-addr = <0x1>;
+	 */
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		hid-descr-addr = <0x20>;
+
+		vdd-supply = <&reg_tp_3p3>;
+
+		interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&hid_touchpad_default>;
+		pinctrl-names = "default";
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+		hid-descr-addr = <0x1>;
+
+		interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&hid_keyboard_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c9 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	alc5682: codec@1a {
+		compatible = "realtek,rt5682i";
+		reg = <0x1a>;
+
+		#sound-dai-cells = <1>;
+
+		interrupt-parent = <&tlmm>;
+		/*
+		 * This will get ignored because the interrupt type
+		 * is set in rt5682.c.
+		 */
+		interrupts = <28 IRQ_TYPE_EDGE_BOTH>;
+
+		pinctrl-0 = <&codec_irq_default>;
+		pinctrl-names = "default";
+
+		AVDD-supply = <&vreg_l15a_1p8>;
+		MICVDD-supply = <&reg_codec_3p3>;
+		VBAT-supply = <&reg_codec_3p3>;
+
+		realtek,dmic1-data-pin = <1>;
+		realtek,dmic1-clk-pin = <1>;
+		realtek,jd-src = <1>;
+	};
+};
+
+&i2c10 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	sn65dsi86_bridge: bridge@2c {
+		compatible = "ti,sn65dsi86";
+		reg = <0x2c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#pwm-cells = <1>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+		suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&bridge_en_default>,
+			<&edp_bridge_irq_default>,
+			<&bridge_suspend_default>;
+		pinctrl-names = "default";
+
+		vpll-supply = <&reg_brij_1p8>;
+		vccio-supply = <&reg_brij_1p8>;
+		vcca-supply = <&reg_brij_1p2>;
+		vcc-supply = <&reg_brij_1p2>;
+
+		clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
+		clock-names = "refclk";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sn65dsi86_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sn65dsi86_out: endpoint {
+					data-lanes = <0 1>;
+					remote-endpoint = <&panel_in_edp>;
+				};
+			};
+		};
+
+		aux-bus {
+			panel: panel {
+				compatible = "edp-panel";
+				power-supply = <&reg_lcm_3p3>;
+				backlight = <&backlight>;
+
+				port {
+					panel_in_edp: endpoint {
+						remote-endpoint = <&sn65dsi86_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&zap_mem>;
+		firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn";
+	};
+};
+
+/* Seems like ADSP really insists on managing those itself */
+&lpasscc { status = "disabled"; };
+&lpass_hm { status = "disabled"; };
+
+&mdp {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&pm6150_adc {
+	thermistor@4e {
+		reg = <ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	charger-thermistor@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm6150_adc_tm {
+	status = "okay";
+
+	charger-thermistor@0 {
+		reg = <0>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm6150_pon { status = "disabled"; };
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn";
+	status = "okay";
+};
+
+&sdhc_1 {
+	pinctrl-0 = <&sdc1_default>;
+	pinctrl-1 = <&sdc1_sleep>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l19a_2p9>;
+	vqmmc-supply = <&vreg_l12a_1p8>;
+
+	status = "okay";
+};
+
+&uart3 {
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
+
+	pinctrl-1 = <&qup_uart3_sleep>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+
+	bluetooth: bluetooth {
+		compatible = "qcom,wcn3991-bt";
+		vddio-supply = <&vreg_l10a_1p8>;
+		vddxo-supply = <&vreg_l1c_1p8>;
+		vddrf-supply = <&vreg_l2c_1p3>;
+		vddch0-supply = <&vreg_l10c_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb_hub_2_x: hub@1 {
+		compatible = "usbbda,5411";
+		reg = <1>;
+		peer-hub = <&usb_hub_3_x>;
+	};
+
+	usb_hub_3_x: hub@2 {
+		compatible = "usbbda,411";
+		reg = <2>;
+		peer-hub = <&usb_hub_2_x>;
+	};
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l4a_0p8>;
+	vdda-pll-supply = <&vreg_l11a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
+	qcom,imp-res-offset-value = <8>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+	qcom,bias-ctrl-value = <0x22>;
+	qcom,charge-ctrl-value = <3>;
+	qcom,hsdisc-trim-value = <0>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l3c_1p2>;
+	vdda-pll-supply = <&vreg_l4a_0p8>;
+	status = "okay";
+};
+
+&venus {
+	firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>;
+	vdd-1.8-xo-supply = <&vreg_l1c_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l2c_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l10c_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l11c_3p3>;
+	status = "okay";
+};
+
+&apps_rsc {
+	pm6150-rpmh-regulators {
+		compatible = "qcom,pm6150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s1a_1p1: smps1 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vreg_l4a_0p8: ldo4 {
+			regulator-min-microvolt = <824000>;
+			regulator-max-microvolt = <928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_0p6: ldo9 {
+			regulator-min-microvolt = <488000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vreg_l11a_1p8: ldo11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_1p8: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_3p0: ldo17 {
+			regulator-min-microvolt = <2920000>;
+			regulator-max-microvolt = <3232000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p8: ldo18 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_2p9: ldo19 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm6150l-rpmh-regulators {
+		compatible = "qcom,pm6150l-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s8c_1p3: smps8 {
+			regulator-min-microvolt = <1120000>;
+			regulator-max-microvolt = <1408000>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-min-microvolt = <1616000>;
+			regulator-max-microvolt = <1984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_1p3: ldo2 {
+			regulator-min-microvolt = <1168000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_1p2: ldo3 {
+			regulator-min-microvolt = <1144000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c_1p8: ldo4 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5c_1p8: ldo5 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l6c_2p9: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p9: ldo9 {
+			regulator-min-microvolt = <2952000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c_3p3: ldo10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c_3p3: ldo11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+&qup_i2c2_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&qup_i2c4_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&qup_i2c9_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&qup_i2c10_default {
+	drive-strength = <2>;
+
+	/* Has external pullup */
+	bias-disable;
+};
+
+&tlmm {
+	/*
+	 * The TZ seem to protect those because some boards can have
+	 * fingerprint sensor connected to this range. Not connected
+	 * on this board
+	 */
+	gpio-reserved-ranges = <58 5>;
+
+	amp_sd_mode_default: amp-sd-mode-deault-state {
+		pins = "gpio23";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	bridge_en_default: bridge-en-default-state {
+		pins = "gpio51";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	bridge_suspend_default: bridge-suspend-default-state {
+		pins = "gpio22";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+	};
+
+	codec_irq_default: codec-irq-deault-state {
+		pins = "gpio28";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	edp_bridge_irq_default: edp-bridge-irq-default-state {
+		pins = "gpio11";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	hid_keyboard_default: hid-keyboard-default-state {
+		pins = "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	hid_touchpad_default: hid-touchpad-default-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	qup_uart3_sleep: qup-uart3-sleep-state {
+		cts-pins {
+			/*
+			 * Configure a pull-down on CTS to match the pull of
+			 * the Bluetooth module.
+			 */
+			pins = "gpio38";
+			function = "gpio";
+			bias-pull-down;
+		};
+
+		rts-pins {
+			/*
+			 * Configure pull-down on RTS. As RTS is active low
+			 * signal, pull it low to indicate the BT SoC that it
+			 * can wakeup the system anytime from suspend state by
+			 * pulling RX low (by sending wakeup bytes).
+			 */
+			pins = "gpio39";
+			function = "gpio";
+			bias-pull-down;
+		};
+
+		tx-pins {
+			/*
+			 * Configure pull-up on TX when it isn't actively driven
+			 * to prevent BT SoC from receiving garbage during sleep.
+			 */
+			pins = "gpio40";
+			function = "gpio";
+			bias-pull-up;
+		};
+
+		rx-pins {
+			/*
+			 * Configure a pull-up on RX. This is needed to avoid
+			 * garbage data when the TX pin of the Bluetooth module
+			 * is floating which may cause spurious wakeups.
+			 */
+			pins = "gpio41";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state {
+		pins = "gpio19";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state {
+		pins = "gpio20";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	reg_lcm_en_default: reg-lcm-en-deault-state {
+		pins = "gpio26";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	reg_audio_en_default: reg-audio-en-deault-state {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	reg_tp_en_default: reg-tp-en-deault-state {
+		pins = "gpio25";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	soc_bkoff_default: soc-bkoff-deault-state {
+		pins = "gpio10";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	sdc1_default: sdc1-default-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			bias-disable;
+			drive-strength = <16>;
+		};
+
+		cmd-pins {
+			pins = "sdc1_cmd";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+
+		data-pins {
+			pins = "sdc1_data";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+
+		rclk-pins {
+			pins = "sdc1_rclk";
+			bias-pull-down;
+		};
+	};
+
+	sdc1_sleep: sdc1-sleep-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		cmd-pins {
+			pins = "sdc1_cmd";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		data-pins {
+			pins = "sdc1_data";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		rclk-pins {
+			pins = "sdc1_rclk";
+			bias-pull-down;
+		};
+	};
+
+	ter_mi2s_active: ter-mi2s-active-state {
+		pins = "gpio63", "gpio64", "gpio65";
+		function = "mi2s_2";
+	};
+};
-- 
2.39.2




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux