Re: [PATCH v4 7/9] arm64: dts: qcom: sa8775p: add high-speed UART nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Mar 8, 2023 at 11:57 AM Konrad Dybcio <konrad.dybcio@xxxxxxxxxx> wrote:
>
>
>
> On 8.03.2023 11:40, Bartosz Golaszewski wrote:
> > From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
> >
> > Add two UART nodes that are known to be used by existing development
> > boards with this SoC.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/sa8775p.dtsi | 31 +++++++++++++++++++++++++++
> >  1 file changed, 31 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> > index 992864e3e0c8..5ebfe8c10eac 100644
> > --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> > @@ -490,6 +490,21 @@ &clk_virt SLAVE_QUP_CORE_1 0>,
> >                               operating-points-v2 = <&qup_opp_table_100mhz>;
> >                               status = "disabled";
> >                       };
> > +
> > +                     uart12: serial@a94000 {
> > +                             compatible = "qcom,geni-uart";
> > +                             reg = <0x0 0x00a94000 0x0 0x4000>;
> > +                             interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> > +                             clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> > +                             clock-names = "se";
> > +                             interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
> > +                                              &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
> > +                                             <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> > +                                              &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
> > +                             interconnect-names = "qup-core", "qup-config";
> > +                             power-domains = <&rpmhpd SA8775P_CX>;
> > +                             status = "disabled";
> > +                     };
> >               };
> >
> >               qupv3_id_2: geniqup@8c0000 {
> > @@ -525,6 +540,22 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>,
> >                               status = "disabled";
> >                       };
> >
> > +                     uart17: serial@88c000 {
> > +                             compatible = "qcom,geni-uart";
> > +                             reg = <0x0 0x0088c000 0x0 0x4000>;
> > +                             interrupts-extended = <&intc GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>,
> > +                                                   <&tlmm 94 IRQ_TYPE_LEVEL_HIGH>;
> This hunk is board-specific and only makes sense if bluetooth
> (or some other "important" peripheral) is connected to this
> uart. Generally the uart interrupt is the one coming from the GIC
> and the other one should probably go to the board dtsi.
>

Right, the second one will be consumed by whatever driver will be
there to control GNSS or bluetooth. I'll drop it in the next spin.

Bart

> Konrad
> > +                             clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
> > +                             clock-names = "se";
> > +                             interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
> > +                                              &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
> > +                                             <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> > +                                              &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
> > +                             interconnect-names = "qup-core", "qup-config";
> > +                             power-domains = <&rpmhpd SA8775P_CX>;
> > +                             status = "disabled";
> > +                     };
> > +
> >                       i2c18: i2c@890000 {
> >                               compatible = "qcom,geni-i2c";
> >                               reg = <0x0 0x00890000 0x0 0x4000>;




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux