Re: [PATCH 7/7] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Kathiravan T <quic_kathirav@xxxxxxxxxxx>]

On 2/14/2023 10:11 PM, Devi Priya wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
> Co-developed-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
> Signed-off-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
> Signed-off-by: Devi Priya <quic_devipriy@xxxxxxxxxxx>
> ---
>   arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts |  28 ++
>   arch/arm64/boot/dts/qcom/ipq9574.dtsi        | 477 ++++++++++++++++++-
>   2 files changed, 499 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> index 2c8430197ec0..21b53f34ce84 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> @@ -8,6 +8,7 @@
>   
>   /dts-v1/;
>   
> +#include <dt-bindings/gpio/gpio.h>
>   #include "ipq9574.dtsi"
>   
>   / {
> @@ -29,6 +30,33 @@
>   	status = "okay";
>   };
>   
> +&pcie1_phy {
> +	status = "okay";
> +};
> +
> +&pcie1_x1 {
> +	perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
> +&pcie2_phy {
> +	status = "okay";
> +};
> +
> +&pcie2_x2 {
> +	perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
> +&pcie3_phy {
> +	status = "okay";
> +};
> +
> +&pcie3_x2 {
> +	perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
>   &sdhc_1 {
>   	pinctrl-0 = <&sdc_default_state>;
>   	pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 062f80798ebb..a32dbdeb5bed 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -6,8 +6,8 @@
>    * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
>    */
>   
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
>   #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>   #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>   
>   / {
> @@ -22,11 +22,41 @@
>   			#clock-cells = <0>;
>   		};
>   
> +		pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <250000000>;
> +			#clock-cells = <0>;
> +		};
> +
> +		pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <250000000>;
> +			#clock-cells = <0>;
> +		};
> +
> +		pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <250000000>;
> +			#clock-cells = <0>;
> +		};
> +
> +		pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <250000000>;
> +			#clock-cells = <0>;
> +		};
> +
>   		sleep_clk: sleep-clk {
>   			compatible = "fixed-clock";
>   			#clock-cells = <0>;
>   		};
>   
> +		usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <125000000>;
> +			#clock-cells = <0>;
> +		};
> +
>   		xo_board_clk: xo-board-clk {
>   			compatible = "fixed-clock";
>   			#clock-cells = <0>;
> @@ -121,6 +151,155 @@
>   		#size-cells = <1>;
>   		ranges = <0 0 0 0xffffffff>;
>   
> +		pcie0_phy: phy@84000 {
> +			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> +			reg = <0x00084000 0x1bc>; /* Serdes PLL */
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> +				 <&gcc GCC_PCIE0_AHB_CLK>,
> +				 <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
> +				 <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
> +			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> +			assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> +			assigned-clock-rates = <20000000>;
> +
> +			resets = <&gcc GCC_PCIE0_PHY_BCR>,
> +				 <&gcc GCC_PCIE0PHY_PHY_BCR>;
> +			reset-names = "phy", "common";
> +
> +			status = "disabled";
> +
> +			pcie0_lane: phy@84200 {
> +				reg = <0x00084200 0x16c>, /* Serdes Tx */
> +				      <0x00084400 0x200>, /* Serdes Rx */
> +				      <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> +				      <0x00084c00 0xf4>;  /* pcs_misc */
> +				#phy-cells = <0>;
> +
> +				clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> +				clock-names = "pipe0";
> +				clock-output-names = "gcc_pcie0_pipe_clk_src";
> +				#clock-cells = <0>;
> +			};
> +		};
> +
> +		pcie2_phy: phy@8c000 {
> +			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> +			reg = <0x0008c000 0x1bc>; /* Serdes PLL */
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> +				 <&gcc GCC_PCIE2_AHB_CLK>,
> +				 <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> +				 <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
> +			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> +			assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
> +			assigned-clock-rates = <20000000>;
> +
> +			resets = <&gcc GCC_PCIE2_PHY_BCR>,
> +				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
> +			reset-names = "phy", "common";
> +
> +			status = "disabled";
> +
> +			pcie2_lanes: phy@8c200 {
> +				reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
> +				      <0x0008c400 0x200>, /* Serdes Rx0 */
> +				      <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
> +				      <0x0008c600 0x16c>, /* Serdes Tx1 */
> +				      <0x0008c800 0x200>, /* Serdes Rx1 */
> +				      <0x0008d400 0x0f8>; /* pcs_misc */
> +
> +				#phy-cells = <0>;
> +
> +				clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
> +				clock-names = "pipe0";
> +				clock-output-names = "gcc_pcie2_pipe_clk_src";
> +				#clock-cells = <0>;
> +			};
> +		};
> +
> +		pcie3_phy: phy@f4000 {
> +			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> +			reg = <0x000f4000 0x1bc>; /* Serdes PLL */
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			clocks = <&gcc GCC_PCIE3_AUX_CLK>,
> +				 <&gcc GCC_PCIE3_AHB_CLK>,
> +				 <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
> +				 <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
> +			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> +			assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
> +			assigned-clock-rates = <20000000>;
> +
> +			resets = <&gcc GCC_PCIE3_PHY_BCR>,
> +				 <&gcc GCC_PCIE3PHY_PHY_BCR>;
> +			reset-names = "phy", "common";
> +
> +			status = "disabled";
> +
> +			pcie3_lanes: phy@f4200 {
> +				reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
> +				      <0x000f4400 0x200>, /* Serdes Rx0 */
> +				      <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
> +				      <0x000f4600 0x16c>, /* Serdes Tx1 */
> +				      <0x000f4800 0x200>, /* Serdes Rx1 */
> +				      <0x000f5400 0x0f8>; /* pcs_misc */
> +
> +				#phy-cells = <0>;
> +
> +				clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
> +				clock-names = "pipe0";
> +				clock-output-names = "gcc_pcie3_pipe_clk_src";
> +				#clock-cells = <0>;
> +			};
> +		};
> +
> +		pcie1_phy: phy@fc000 {
> +			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> +			reg = <0x000fc000 0x1bc>; /* Serdes PLL */
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
> +				 <&gcc GCC_PCIE1_AHB_CLK>,
> +				 <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
> +				 <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
> +			clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
> +
> +			assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
> +			assigned-clock-rates = <20000000>;
> +
> +			resets = <&gcc GCC_PCIE1_PHY_BCR>,
> +				 <&gcc GCC_PCIE1PHY_PHY_BCR>;
> +			reset-names = "phy", "common";
> +
> +			status = "disabled";
> +
> +			pcie1_lane: phy@fc200 {
> +				reg = <0x000fc200 0x16c>, /* Serdes Tx */
> +				      <0x000fc400 0x200>, /* Serdes Rx */
> +				      <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> +				      <0x000fcc00 0xf4>;  /* pcs_misc */
> +				#phy-cells = <0>;
> +
> +				clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> +				clock-names = "pipe0";
> +				clock-output-names = "gcc_pcie1_pipe_clk_src";
> +				#clock-cells = <0>;
> +			};
> +		};
> +
>   		tlmm: pinctrl@1000000 {
>   			compatible = "qcom,ipq9574-tlmm";
>   			reg = <0x01000000 0x300000>;
> @@ -145,11 +324,11 @@
>   			clocks = <&xo_board_clk>,
>   				 <&sleep_clk>,
>   				 <&bias_pll_ubi_nc_clk>,
> -				 <0>,
> -				 <0>,
> -				 <0>,
> -				 <0>,
> -				 <0>;
> +				 <&pcie30_phy0_pipe_clk>,
> +				 <&pcie30_phy1_pipe_clk>,
> +				 <&pcie30_phy2_pipe_clk>,
> +				 <&pcie30_phy3_pipe_clk>,
> +				 <&usb3phy_0_cc_pipe_clk>;


pipe clock source is PHY. So should we add the pcie_phy phandle here and 
use it like how it is done in other targets, ex: sm8550.dtsi?


>   			#clock-cells = <1>;
>   			#reset-cells = <1>;
>   			#power-domain-cells = <1>;
> @@ -282,6 +461,292 @@
>   				status = "disabled";
>   			};
>   		};
> +
> +		pcie1_x1: pci@10000000 {
> +			compatible = "qcom,pcie-ipq9574";
> +			reg =  <0x10000000 0xf1d>,
> +			       <0x10000F20 0xa8>,
> +			       <0x10001000 0x1000>,
> +			       <0x000F8000 0x4000>,
> +			       <0x10100000 0x1000>,
> +			       <0x00618108 0x4>;
> +			reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
> +			device_type = "pci";
> +			linux,pci-domain = <2>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <1>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x81000000 0 0x10200000 0x10200000
> +				  0 0x00100000   /* downstream I/O */
> +				  0x82000000 0 0x10300000 0x10300000
> +				  0 0x07d00000>; /* non-prefetchable memory */
> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 35
> +					IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc 0 49
> +					IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc 0 84
> +					IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc 0 85
> +					IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "global_irq";


Controller driver doesn't support the "global_irq" yet. Please correct 
me If I am wrong.


Thanks, Kathiravan T.