Re: [PATCH v2 3/5] arm64: dts: qcom: sm8350: add dp controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 10/02/2023 12:08, Dmitry Baryshkov wrote:
On 10/02/2023 12:34, Neil Armstrong wrote:
Add the Display Port controller subnode to the MDSS node.

Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/sm8350.dtsi | 82 +++++++++++++++++++++++++++++++++++-
  1 file changed, 80 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index d490ce84a022..eb636b7dffa7 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -2862,13 +2862,20 @@ ports {
                      port@0 {
                          reg = <0>;
-                        dpu_intf1_out: endpoint {
-                            remote-endpoint = <&mdss_dsi0_in>;
+                        dpu_intf0_out: endpoint {
+                            remote-endpoint = <&mdss_dp_in>;

No need to reorder these ports. Please add DP to the end.

Right, but I'll keep the dpu_intf0_out label for this port,
but having dpu_intf1_out, dpu_intf2_out then dpu_intf0_out isn't very clean...


                          };
                      };
                      port@1 {
                          reg = <1>;
+                        dpu_intf1_out: endpoint {
+                            remote-endpoint = <&mdss_dsi0_in>;
+                        };
+                    };
+
+                    port@2 {
+                        reg = <2>;
                          dpu_intf2_out: endpoint {
                              remote-endpoint = <&mdss_dsi1_in>;
                          };
@@ -2876,6 +2883,77 @@ dpu_intf2_out: endpoint {
                  };
              };
+            mdss_dp: displayport-controller@ae90000 {
+                compatible = "qcom,sm8350-dp";
+                reg = <0 0xae90000 0 0x200>,
+                      <0 0xae90200 0 0x200>,
+                      <0 0xae90400 0 0x600>,
+                      <0 0xae91000 0 0x400>;

This will not validate against the schema. Please add p1 region at the end (I assume it is <0 0x0ae91400 0 0x400>).

+                interrupt-parent = <&mdss>;
+                interrupts = <12>;
+                clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+                     <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+                     <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+                     <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+                     <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+                clock-names = "core_iface",
+                          "core_aux",
+                          "ctrl_link",
+                                  "ctrl_link_iface",
+                          "stream_pixel";
+
+                assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+                          <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+                assigned-clock-parents = <&usb_1_qmpphy 1>,
+                             <&usb_1_qmpphy 2>;

Please use defined names here and in the phys below

Ack, will do in all the patches


+
+                phys = <&usb_1_qmpphy 1>;
+                    phy-names = "dp";
+
+                    #sound-dai-cells = <0>;
+
+                operating-points-v2 = <&dp_opp_table>;
+                power-domains = <&rpmhpd SM8350_MMCX>;
+
+                status = "disabled";
+
+                ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        mdss_dp_in: endpoint {
+                            remote-endpoint = <&dpu_intf0_out>;
+                        };
+                    };
+                };
+
+                dp_opp_table: opp-table {
+                    compatible = "operating-points-v2";
+
+                    opp-160000000 {
+                        opp-hz = /bits/ 64 <160000000>;
+                        required-opps = <&rpmhpd_opp_low_svs>;
+                    };
+
+                    opp-270000000 {
+                        opp-hz = /bits/ 64 <270000000>;
+                        required-opps = <&rpmhpd_opp_svs>;
+                    };
+
+                    opp-540000000 {
+                        opp-hz = /bits/ 64 <540000000>;
+                        required-opps = <&rpmhpd_opp_svs_l1>;
+                    };
+
+                    opp-810000000 {
+                        opp-hz = /bits/ 64 <810000000>;
+                        required-opps = <&rpmhpd_opp_nom>;
+                    };
+                };
+            };
+
              mdss_dsi0: dsi@ae94000 {
                  compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
                  reg = <0 0x0ae94000 0 0x400>;






[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux