Re: [PATCH 2/4] arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 8.02.2023 16:57, Bjorn Andersson wrote:
> On Wed, Feb 08, 2023 at 09:14:46AM +0100, Konrad Dybcio wrote:
>>
>>
>> On 8.02.2023 04:46, Bjorn Andersson wrote:
>>> From: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
>>>
>>> The SC8280XP CRD control over battery management and its two USB Type-C
>>> port using pmic_glink and two GPIO-based SBU muxes.
>>>
>>> Enable the two DisplayPort instances, GPIO SBU mux instance and
>>> pmic_glink with the two connectors on the CRD.
>>>
>>> Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
>>> Signed-off-by: Bjorn Andersson <quic_bjorande@xxxxxxxxxxx>
>>> ---
>>>  arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 191 +++++++++++++++++++++-
>>>  1 file changed, 189 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
>>> index 3f116a879e22..35b63c3962f0 100644
>>> --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
>>> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
>>> @@ -36,6 +36,77 @@ chosen {
>>>  		stdout-path = "serial0:115200n8";
>>>  	};
>>>  
>>> +	pmic-glink {
>>> +		compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
>>> +
>>> +		#address-cells = <1>;
>>> +		#size-cells = <0>;
>>> +
>>> +		connector@0 {
>>> +			compatible = "usb-c-connector";
>>> +			reg = <0>;
>>> +			power-role = "dual";
>>> +			data-role = "dual";
>>> +
>>> +			ports {
>>> +				#address-cells = <1>;
>>> +				#size-cells = <0>;
>> Add a newline between the last propreties and first subnodes, please.
>>
>>> +				port@0 {
>>> +					reg = <0>;
>>> +					pmic_glink_con0_hs: endpoint {
>>> +						remote-endpoint = <&usb_0_role_switch>;
>>> +					};
>>> +				};
>>> +
>>> +				port@1 {
>>> +					reg = <1>;
>>> +					pmic_glink_con0_ss: endpoint {
>>> +						remote-endpoint = <&mdss0_dp0_out>;
>>> +					};
>>> +				};
>>> +
>>> +				port@2 {
>>> +					reg = <2>;
>>> +					pmic_glink_con0_sbu: endpoint {
>>> +						remote-endpoint = <&usb0_sbu_mux>;
>>> +					};
>>> +				};
>>> +			};
>>> +		};
>>> +
>>> +		connector@1 {
>>> +			compatible = "usb-c-connector";
>>> +			reg = <1>;
>>> +			power-role = "dual";
>>> +			data-role = "dual";
>>> +
>>> +			ports {
>>> +				#address-cells = <1>;
>>> +				#size-cells = <0>;
>>> +				port@0 {
>>> +					reg = <0>;
>>> +					pmic_glink_con1_hs: endpoint {
>>> +						remote-endpoint = <&usb_1_role_switch>;
>>> +					};
>>> +				};
>>> +
>>> +				port@1 {
>>> +					reg = <1>;
>>> +					pmic_glink_con1_ss: endpoint {
>>> +						remote-endpoint = <&mdss0_dp1_out>;
>>> +					};
>>> +				};
>>> +
>>> +				port@2 {
>>> +					reg = <2>;
>>> +					pmic_glink_con1_sbu: endpoint {
>>> +						remote-endpoint = <&usb1_sbu_mux>;
>>> +					};
>>> +				};
>>> +			};
>>> +		};
>>> +	};
>>> +
>>>  	vreg_edp_3p3: regulator-edp-3p3 {
>>>  		compatible = "regulator-fixed";
>>>  
>>> @@ -139,6 +210,46 @@ linux,cma {
>>>  			linux,cma-default;
>>>  		};
>>>  	};
>>> +
>>> +	usb0-sbu-mux {
>>> +		compatible = "pericom,pi3usb102", "gpio-sbu-mux";
>>> +
>>> +		enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
>>> +		select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
>>> +
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&usb0_sbu_default>;
>>> +
>>> +		mode-switch;
>>> +		orientation-switch;
>>> +		svid = /bits/ 16 <0xff01>;
>>> +
>>> +		port {
>>> +			usb0_sbu_mux: endpoint {
>>> +				remote-endpoint = <&pmic_glink_con0_sbu>;
>>> +			};
>>> +		};
>>> +	};
>>> +
>>> +	usb1-sbu-mux {
>>> +		compatible = "pericom,pi3usb102", "gpio-sbu-mux";
>>> +
>>> +		enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
>>> +		select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
>>> +
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&usb1_sbu_default>;
>>> +
>>> +		mode-switch;
>>> +		orientation-switch;
>>> +		svid = /bits/ 16 <0xff01>;
>>> +
>>> +		port {
>>> +			usb1_sbu_mux: endpoint {
>>> +				remote-endpoint = <&pmic_glink_con1_sbu>;
>>> +			};
>>> +		};
>>> +	};
>>>  };
>>>  
>>>  &apps_rsc {
>>> @@ -262,6 +373,36 @@ &mdss0 {
>>>  	status = "okay";
>>>  };
>>>  
>>> +&mdss0_dp0 {
>>> +	status = "okay";
>>> +
>>> +	data-lanes = <0 1>;
>> Status last; is this really only 2 lanes?
>>
>>> +
>>> +	ports {
>>> +		port@1 {
>>> +			reg = <1>;
>>> +			mdss0_dp0_out: endpoint {
>>> +				remote-endpoint = <&pmic_glink_con0_ss>;
>>> +			};
>>> +		};
>>> +	};
>>> +};
>>> +
>>> +&mdss0_dp1 {
>>> +	status = "okay";
>>> +
>>> +	data-lanes = <0 1>;
>> Ditto
>>
>>> +
>>> +	ports {
>>> +		port@1 {
>>> +			reg = <1>;
>>> +			mdss0_dp1_out: endpoint {
>>> +				remote-endpoint = <&pmic_glink_con1_ss>;
>>> +			};
>>> +		};
>>> +	};
>>> +};
>>> +
>>>  &mdss0_dp3 {
>>>  	compatible = "qcom,sc8280xp-edp";
>>>  	/delete-property/ #sound-dai-cells;
>>> @@ -480,8 +621,13 @@ &usb_0 {
>>>  };
>>>  
>>>  &usb_0_dwc3 {
>>> -	/* TODO: Define USB-C connector properly */
>>>  	dr_mode = "host";
>>> +
>>> +	port {
>>> +		usb_0_role_switch: endpoint {
>>> +			remote-endpoint = <&pmic_glink_con0_hs>;
>>> +		};
>> This should be defined in the SoC DTSI, it's a standard dwc3 binding
>> with usb HS / SS / SBU ports. Especially since we can feed the endpoint
>> from any device now, as pmic-glink should work everywhere.
>>
> 
> The sa8295p/sa8540p boards, derived from sc8280xp does not implement
> pmic_glink, so it seems moving this to the soc.dtsi would be messy.
> 
>> Or /omit-if-no-ref/, I suppose.
>>
> 
> Or you're saying I should put the skeleton of the port definition in the
> soc.dtsi and then fill it out the remote-endpoint here; and mark it
> omit-if-no-ref to avoid binding warnings?
I thought omit-if-no-ref actually omits the node before resolving phandles
that it references, but it seems to not be the case.. Still, we can define
the ports in the SoC DTSI and assign endpoints per-device (like we do with
DSI for example).

Konrad
> 
>>> +	};
>>>  };
>>>  
>>>  &usb_0_hsphy {
>>> @@ -504,8 +650,13 @@ &usb_1 {
>>>  };
>>>  
>>>  &usb_1_dwc3 {
>>> -	/* TODO: Define USB-C connector properly */
>>>  	dr_mode = "host";
>>> +
>>> +	port {
>>> +		usb_1_role_switch: endpoint {
>>> +			remote-endpoint = <&pmic_glink_con1_hs>;
>>> +		};
>>> +	};
>>>  };
>>>  
>>>  &usb_1_hsphy {
>>> @@ -709,4 +860,40 @@ reset-n-pins {
>>>  			drive-strength = <16>;
>>>  		};
>>>  	};
>>> +
>>> +	usb0_sbu_default: usb0-sbu-state {
>>> +		oe-n-pins {
>>> +			pins = "gpio101";
>>> +			function = "gpio";
>> No drive-strength/bias/i/o?
>>
> 
> Seems like a reasonable ask...
> 
> Thanks,
> Bjorn
> 
>> Konrad
>>> +		};
>>> +
>>> +		sel-pins {
>>> +			pins = "gpio164";
>>> +			function = "gpio";
>>> +		};
>>> +
>>> +		mode-pins {
>>> +			pins = "gpio167";
>>> +			function = "gpio";
>>> +			output-high;
>>> +		};
>>> +	};
>>> +
>>> +	usb1_sbu_default: usb1-sbu-state {
>>> +		oe-n-pins {
>>> +			pins = "gpio48";
>>> +			function = "gpio";
>>> +		};
>>> +
>>> +		sel-pins {
>>> +			pins = "gpio47";
>>> +			function = "gpio";
>>> +		};
>>> +
>>> +		mode-pins {
>>> +			pins = "gpio50";
>>> +			function = "gpio";
>>> +			output-high;
>>> +		};
>>> +	};
>>>  };



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux