Re: [PATCH v9 08/27] mailbox: Add Gunyah message queue mailbox

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 20/01/2023 22:46, Elliot Berman wrote:
Gunyah message queues are a unidirectional inter-VM pipe for messages up
to 1024 bytes. This driver supports pairing a receiver message queue and
a transmitter message queue to expose a single mailbox channel.

Signed-off-by: Elliot Berman <quic_eberman@xxxxxxxxxxx>
---
  Documentation/virt/gunyah/message-queue.rst |   8 +
  MAINTAINERS                                 |   1 +
  drivers/mailbox/Makefile                    |   2 +
  drivers/mailbox/gunyah-msgq.c               | 214 ++++++++++++++++++++
  include/linux/gunyah.h                      |  59 +++++-
  5 files changed, 283 insertions(+), 1 deletion(-)
  create mode 100644 drivers/mailbox/gunyah-msgq.c

diff --git a/Documentation/virt/gunyah/message-queue.rst b/Documentation/virt/gunyah/message-queue.rst
index 0667b3eb1ff9..082085e981e0 100644
--- a/Documentation/virt/gunyah/message-queue.rst
+++ b/Documentation/virt/gunyah/message-queue.rst
@@ -59,3 +59,11 @@ vIRQ: two TX message queues will have two vIRQs (and two capability IDs).
        |               |         |                 |         |               |
        |               |         |                 |         |               |
        +---------------+         +-----------------+         +---------------+
+
+Gunyah message queues are exposed as mailboxes. To create the mailbox, create
+a mbox_client and call `gh_msgq_init`. On receipt of the RX_READY interrupt,
+all messages in the RX message queue are read and pushed via the `rx_callback`
+of the registered mbox_client.
+
+.. kernel-doc:: drivers/mailbox/gunyah-msgq.c
+   :identifiers: gh_msgq_init
diff --git a/MAINTAINERS b/MAINTAINERS
index fe19e71efc6d..d02e8abe6457 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9049,6 +9049,7 @@ S:	Supported
  F:	Documentation/devicetree/bindings/firmware/gunyah-hypervisor.yaml
  F:	Documentation/virt/gunyah/
  F:	arch/arm64/gunyah/
+F:	drivers/mailbox/gunyah-msgq.c
  F:	drivers/virt/gunyah/
  F:	include/linux/gunyah.h
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index fc9376117111..5f929bb55e9a 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -55,6 +55,8 @@ obj-$(CONFIG_MTK_CMDQ_MBOX)	+= mtk-cmdq-mailbox.o
obj-$(CONFIG_ZYNQMP_IPI_MBOX) += zynqmp-ipi-mailbox.o +obj-$(CONFIG_GUNYAH) += gunyah-msgq.o
+
  obj-$(CONFIG_SUN6I_MSGBOX)	+= sun6i-msgbox.o
obj-$(CONFIG_SPRD_MBOX) += sprd-mailbox.o
diff --git a/drivers/mailbox/gunyah-msgq.c b/drivers/mailbox/gunyah-msgq.c
new file mode 100644
index 000000000000..caa283f7248b
--- /dev/null
+++ b/drivers/mailbox/gunyah-msgq.c
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <linux/mailbox_controller.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/gunyah.h>
+#include <linux/printk.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+
+#define mbox_chan_to_msgq(chan) (container_of(chan->mbox, struct gh_msgq, mbox))
+
+static irqreturn_t gh_msgq_rx_irq_handler(int irq, void *data)
+{
+	struct gh_msgq *msgq = data;
+	struct gh_msgq_rx_data rx_data;
+	unsigned long gh_err;
+	bool ready = true;
+
+	while (ready) {
+		gh_err = gh_hypercall_msgq_recv(msgq->rx_ghrsc->capid,
+				(uintptr_t)&rx_data.data, sizeof(rx_data.data),
you should proabably use GH_MSGQ_MAX_MSG_SIZE instead of calling sizeof for every loop.

+				&rx_data.length, &ready);
+		if (gh_err == GH_ERROR_OK) {
+			mbox_chan_received_data(gh_msgq_chan(msgq), &rx_data);
+		} else if (gh_err == GH_ERROR_MSGQUEUE_EMPTY) {
+			break;
+		} else {
+			pr_warn("Failed to receive data from msgq for %s: %zd\n",
+				msgq->mbox.dev ? dev_name(msgq->mbox.dev) : "", gh_err);
+			break;
+		}
+	}
+
+	return IRQ_HANDLED;
+}
How about making this more readable.
also use of gh_ in local variables is not really adding any value.

while (ready) {
	err = gh_hypercall_msgq_recv(...);
	if (err) {
		if (err != GH_ERROR_MSGQUEUE_EMPTY)
dev_warn(msgq->mbox.dev, "Failed to receive data %zd\n", err);
        		break;

               }
	mbox_chan_received_data(gh_msgq_chan(msgq), &rx_data);
}


+
+static irqreturn_t gh_msgq_tx_irq_handler(int irq, void *data)
+{
+	struct gh_msgq *msgq = data;
+
+	mbox_chan_txdone(gh_msgq_chan(msgq), 0);
What is this irq for? Is it for tx done ack?

+
+	return IRQ_HANDLED;
+}
+
+static void gh_msgq_txdone_tasklet(struct tasklet_struct *tasklet)
+{
+	struct gh_msgq *msgq = container_of(tasklet, struct gh_msgq, txdone_tasklet);
+
+	mbox_chan_txdone(gh_msgq_chan(msgq), msgq->last_ret);
+}
+
+static int gh_msgq_send_data(struct mbox_chan *chan, void *data)
+{
+	struct gh_msgq *msgq = mbox_chan_to_msgq(chan);
+	struct gh_msgq_tx_data *msgq_data = data;
+	u64 tx_flags = 0;
+	unsigned long ret;
+	bool ready;
+
+	if (msgq_data->push)
+		tx_flags |= GH_HYPERCALL_MSGQ_TX_FLAGS_PUSH;
+
+	ret = gh_hypercall_msgq_send(msgq->tx_ghrsc->capid, msgq_data->length,
+					(uintptr_t)msgq_data->data, tx_flags, &ready);
+
+	/**
+	 * unlikely because Linux tracks state of msgq and should not try to
+	 * send message when msgq is full.
+	 */
+	if (unlikely(ret == GH_ERROR_MSGQUEUE_FULL))
+		return -EAGAIN;
+
+	/**
+	 * Propagate all other errors to client. If we return error to mailbox
+	 * framework, then no other messages can be sent and nobody will know
+	 * to retry this message.
+	 */
+	msgq->last_ret = gh_remap_error(ret);
+
+	/**
+	 * This message was successfully sent, but message queue isn't ready to
+	 * receive more messages because it's now full. Mailbox framework
+	 * requires that we only report that message was transmitted when
+	 * we're ready to transmit another message. We'll get that in the form
+	 * of tx IRQ once the other side starts to drain the msgq.
+	 */
+	if (ret == GH_ERROR_OK && !ready)
+		return 0;
+
+	/**
+	 * We can send more messages. Mailbox framework requires that tx done
+	 * happens asynchronously to sending the message. Gunyah message queues
+	 * tell us right away on the hypercall return whether we can send more
+	 * messages. To work around this, defer the txdone to a tasklet.
+	 */
+	tasklet_schedule(&msgq->txdone_tasklet);
+
+	return 0;
+}
+
+static struct mbox_chan_ops gh_msgq_ops = {
+	.send_data = gh_msgq_send_data,
+};
+
+/**
+ * gh_msgq_init() - Initialize a Gunyah message queue with an mbox_client
+ * @parent: optional, device parent used for the mailbox controller
+ * @msgq: Pointer to the gh_msgq to initialize
+ * @cl: A mailbox client to bind to the mailbox channel that the message queue creates
+ * @tx_ghrsc: optional, the transmission side of the message queue
+ * @rx_ghrsc: optional, the receiving side of the message queue
+ *
+ * At least one of tx_ghrsc and rx_ghrsc should be not NULL. Most message queue use cases come with
+ * a pair of message queues to facilitate bidirectional communication. When tx_ghrsc is set,
+ * the client can send messages with mbox_send_message(gh_msgq_chan(msgq), msg). When rx_ghrsc
+ * is set, the mbox_client should register an .rx_callback() and the message queue driver will
+ * push all available messages upon receiving the RX ready interrupt. The messages should be
+ * consumed or copied by the client right away as the gh_msgq_rx_data will be replaced/destroyed
+ * after the callback.
+ *
+ * Returns - 0 on success, negative otherwise
+ */
+int gh_msgq_init(struct device *parent, struct gh_msgq *msgq, struct mbox_client *cl,
+		     struct gunyah_resource *tx_ghrsc, struct gunyah_resource *rx_ghrsc)
+{
+	int ret;
+
+	/* Must have at least a tx_ghrsc or rx_ghrsc and that they are the right device types */
+	if ((!tx_ghrsc && !rx_ghrsc) ||
+	    (tx_ghrsc && tx_ghrsc->type != GUNYAH_RESOURCE_TYPE_MSGQ_TX) ||
+	    (rx_ghrsc && rx_ghrsc->type != GUNYAH_RESOURCE_TYPE_MSGQ_RX))
+		return -EINVAL;
+
+	if (gh_api_version() != GUNYAH_API_V1) {
+		pr_warn("Unrecognized gunyah version: %u. Currently supported: %d\n",
+			gh_api_version(), GUNYAH_API_V1);
how about using dev_err here?

+		return -ENODEV;

-EOPNOTSUPP?

+	}
+
+	if (!gh_api_has_feature(GH_API_FEATURE_MSGQUEUE))
+		return -EOPNOTSUPP;
+
+	msgq->tx_ghrsc = tx_ghrsc;
+	msgq->rx_ghrsc = rx_ghrsc;
+
+	msgq->mbox.dev = parent;
+	msgq->mbox.ops = &gh_msgq_ops;
+	msgq->mbox.num_chans = 1;
+	msgq->mbox.chans = kcalloc(msgq->mbox.num_chans, sizeof(*msgq->mbox.chans), GFP_KERNEL);
+	if (!msgq->mbox.chans)
+		return -ENOMEM;

new line here would be nice.
+	msgq->mbox.txdone_irq = true;
+
+	if (msgq->tx_ghrsc) {
+		ret = request_irq(msgq->tx_ghrsc->irq, gh_msgq_tx_irq_handler, 0, "gh_msgq_tx",
+				msgq);
+		if (ret)
+			goto err_chans;
+	}
+
+	if (msgq->rx_ghrsc) {
+		ret = request_threaded_irq(msgq->rx_ghrsc->irq, NULL, gh_msgq_rx_irq_handler,
+						IRQF_ONESHOT, "gh_msgq_rx", msgq);
+		if (ret)
+			goto err_tx_irq;
+	}
+
+	tasklet_setup(&msgq->txdone_tasklet, gh_msgq_txdone_tasklet);

AFAIU, this looks like duplicating what core already has with TXDONE_BY_POLL.

can we not use
txdone_poll = true
and implement last_tx_done callback to use hrtimer from the core to tick tx.

--srini
+
+	ret = mbox_controller_register(&msgq->mbox);
+	if (ret)
+		goto err_rx_irq;
+
+	ret = mbox_bind_client(gh_msgq_chan(msgq), cl);
+	if (ret)
+		goto err_mbox;
+
+	return 0;
+err_mbox:
+	mbox_controller_unregister(&msgq->mbox);
+err_rx_irq:
+	if (msgq->rx_ghrsc)
+		free_irq(msgq->rx_ghrsc->irq, msgq);
+err_tx_irq:
+	if (msgq->tx_ghrsc)
+		free_irq(msgq->tx_ghrsc->irq, msgq);
+err_chans:
+	kfree(msgq->mbox.chans);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(gh_msgq_init);
+
+void gh_msgq_remove(struct gh_msgq *msgq)
+{
+	mbox_controller_unregister(&msgq->mbox);
+
+	if (msgq->rx_ghrsc)
+		free_irq(msgq->rx_ghrsc->irq, msgq);
+
+	if (msgq->tx_ghrsc)
+		free_irq(msgq->tx_ghrsc->irq, msgq);
+
+	kfree(msgq->mbox.chans);
+}
+EXPORT_SYMBOL_GPL(gh_msgq_remove);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Gunyah Message Queue Driver");
diff --git a/include/linux/gunyah.h b/include/linux/gunyah.h
index b5f61c14ec1e..5d6fc9f88718 100644
--- a/include/linux/gunyah.h
+++ b/include/linux/gunyah.h
@@ -8,10 +8,67 @@
#include <linux/bitfield.h>
  #include <linux/errno.h>
+#include <linux/interrupt.h>
  #include <linux/limits.h>
+#include <linux/mailbox_controller.h>
+#include <linux/mailbox_client.h>
  #include <linux/types.h>
-/* Common Gunyah macros */
+/* Follows resource manager's resource types for VM_GET_HYP_RESOURCES */
+enum gunyah_resource_type {
+	GUNYAH_RESOURCE_TYPE_BELL_TX	= 0,
+	GUNYAH_RESOURCE_TYPE_BELL_RX	= 1,
+	GUNYAH_RESOURCE_TYPE_MSGQ_TX	= 2,
+	GUNYAH_RESOURCE_TYPE_MSGQ_RX	= 3,
+	GUNYAH_RESOURCE_TYPE_VCPU	= 4,
+};
+
+struct gunyah_resource {
+	enum gunyah_resource_type type;
+	u64 capid;
+	int irq;
+};
+
+/**
+ * Gunyah Message Queues
+ */
+
+#define GH_MSGQ_MAX_MSG_SIZE	240
+
+struct gh_msgq_tx_data {
+	size_t length;
+	bool push;
+	char data[];
+};
+
+struct gh_msgq_rx_data {
+	size_t length;
+	char data[GH_MSGQ_MAX_MSG_SIZE];
+};
+
+struct gh_msgq {
+	struct gunyah_resource *tx_ghrsc;
+	struct gunyah_resource *rx_ghrsc;
+
+	/* msgq private */
+	int last_ret; /* Linux error, not GH_STATUS_* */
+	struct mbox_controller mbox;
+	struct tasklet_struct txdone_tasklet;
+};
+
+
+int gh_msgq_init(struct device *parent, struct gh_msgq *msgq, struct mbox_client *cl,
+		     struct gunyah_resource *tx_ghrsc, struct gunyah_resource *rx_ghrsc);
+void gh_msgq_remove(struct gh_msgq *msgq);
+
+static inline struct mbox_chan *gh_msgq_chan(struct gh_msgq *msgq)
+{
+	return &msgq->mbox.chans[0];
+}
+
+/******************************************************************************/
+/* Common arch-independent macros and definitions for Gunyah hypercalls */
+
  #define GH_CAPID_INVAL	U64_MAX
  #define GH_VMID_ROOT_VM	0xff



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux