On 31/01/2023 05:38, Steev Klimaszewski wrote:
> Signed-off-by: Steev Klimaszewski <steev@xxxxxxxx>
> ---
> .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 68 +++++++++++++++++++
> 1 file changed, 68 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> index f936b020a71d..951438ac5946 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> @@ -24,6 +24,8 @@ / {
> aliases {
> i2c4 = &i2c4;
> i2c21 = &i2c21;
> + serial0 = &uart17;
> + serial1 = &uart2;
> };
>
> wcd938x: audio-codec {
> @@ -712,6 +714,32 @@ &qup0 {
> status = "okay";
> };
>
> +&uart2 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_state>;
> +
> + bluetooth {
> + compatible = "qcom,wcn6855-bt";
> +
> +/*
Why dead code should be in the kernel?
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + vddch1-supply = <&vreg_l23a_3p3>;
> +*/
> + max-speed = <3200000>;
> +
> + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
> + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_en>;
> + };
> +};
> +
> &qup1 {
> status = "okay";
> };
> @@ -720,6 +748,12 @@ &qup2 {
> status = "okay";
> };
>
> +&uart17 {
> + compatible = "qcom,geni-debug-uart";
> +
> + status = "okay";
> +};
> +
> &remoteproc_adsp {
> firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn";
>
> @@ -980,6 +1014,19 @@ hastings_reg_en: hastings-reg-en-state {
> &tlmm {
> gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>
> + bt_en: bt-en-state {
> + hstp-sw-ctrl {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
> + pins = "gpio132";
> + function = "gpio";
> + };
> +
> + hstp-bt-en {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <16>;
> + };
> + };
> +
> edp_reg_en: edp-reg-en-state {
> pins = "gpio25";
> function = "gpio";
> @@ -1001,6 +1048,27 @@ i2c4_default: i2c4-default-state {
> bias-disable;
> };
>
> + uart2_state: uart2-state {
> + cts {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
Best regards,
Krzysztof
