Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
differences to msm8916.
- big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
- DRAM 1x800 LPDDR3
- Camera 4+4 lane CSI
- Venus @ 1080p60 HEVC
- DSI x 2
- Adreno A405
- WiFi wcn3660/wcn3680b 802.11ac
Co-developed-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
Signed-off-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
Co-developed-by: Jun Nie <jun.nie@xxxxxxxxxx>
Signed-off-by: Jun Nie <jun.nie@xxxxxxxxxx>
Co-developed-by: Benjamin Li <benl@xxxxxxxxxxxx>
Signed-off-by: Benjamin Li <benl@xxxxxxxxxxxx>
Co-developed-by: James Willcox <jwillcox@xxxxxxxxxxxx>
Signed-off-by: James Willcox <jwillcox@xxxxxxxxxxxx>
Co-developed-by: Leo Yan <leo.yan@xxxxxxxxxx>
Signed-off-by: Leo Yan <leo.yan@xxxxxxxxxx>
Co-developed-by: Joseph Gates <jgates@xxxxxxxxxxxx>
Signed-off-by: Joseph Gates <jgates@xxxxxxxxxxxx>
Co-developed-by: Max Chen <mchen@xxxxxxxxxxxx>
Signed-off-by: Max Chen <mchen@xxxxxxxxxxxx>
Co-developed-by: Zac Crosby <zac@xxxxxxxxxxxx>
Signed-off-by: Zac Crosby <zac@xxxxxxxxxxxx>
Co-developed-by: Vincent Knecht <vincent.knecht@xxxxxxxxxx>
Signed-off-by: Vincent Knecht <vincent.knecht@xxxxxxxxxx>
Co-developed-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/msm8939.dtsi | 2353 +++++++++++++++++++++++++
1 file changed, 2353 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
new file mode 100644
index 0000000000000..125e0c5314e63
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
@@ -0,0 +1,2353 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2023, Linaro Limited
+ */
+
+#include <dt-bindings/clock/qcom,gcc-msm8939.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interconnect/qcom,msm8939.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8939.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ /*
+ * Stock LK wants address-cells/size-cells = 2
+ * A number of our drivers want address/size cells = 1
+ * hence the disparity between top-level and /soc below.
+ */
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <19200000>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu@100 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x100>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ L2_1: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU1: cpu@101 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x101>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ CPU2: cpu@102 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x102>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc2>;
+ qcom,saw = <&saw2>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ CPU3: cpu@103 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x103>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc3>;
+ qcom,saw = <&saw3>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ CPU4: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x0>;
+ qcom,acc = <&acc4>;
+ qcom,saw = <&saw4>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU5: cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x1>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc5>;
+ qcom,saw = <&saw5>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ CPU6: cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x2>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc6>;
+ qcom,saw = <&saw6>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ CPU7: cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x3>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc7>;
+ qcom,saw = <&saw7>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ idle-states {
+ CPU_SLEEP_0: cpu-sleep-0 {
+ compatible ="qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <130>;
+ exit-latency-us = <150>;
+ min-residency-us = <2000>;
+ local-timer-stop;
+ };
+ };
+ };
+
+ /*
+ * MSM8939 has a big.LITTLE heterogeneous computing architecture,
+ * consisting of two clusters of four ARM Cortex-A53s each. The
+ * LITTLE cluster runs at 1.0-1.2GHz, and the big cluster runs
+ * at 1.5-1.7GHz.
+ *
+ * The enable method used here is spin-table which presupposes use
+ * of a 2nd stage boot shim such as lk2nd to have installed a
+ * spin-table, the downstream non-psci/non-spin-table method that
+ * default msm8916/msm8936/msm8939 will not be supported upstream.
+ */
+ cpu-map {
+ /* LITTLE (efficiency) cluster */
+ cluster0 {
+ core0 {
+ cpu = <&CPU4>;
+ };
+
+ core1 {
+ cpu = <&CPU5>;
+ };
+
+ core2 {
+ cpu = <&CPU6>;
+ };
+
+ core3 {
+ cpu = <&CPU7>;
+ };
+ };
+
+ /* big (performance) cluster */
+ /* Boot CPU is cluster 1 core 0 */
+ cluster1 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+
+ core2 {
+ cpu = <&CPU2>;
+ };
+
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-msm8916", "qcom,scm";
+ clocks = <&gcc GCC_CRYPTO_CLK>,
+ <&gcc GCC_CRYPTO_AXI_CLK>,
+ <&gcc GCC_CRYPTO_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ #reset-cells = <1>;
+
+ qcom,dload-mode = <&tcsr 0x6100>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the reg */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz-apps@86000000 {
+ reg = <0x0 0x86000000 0x0 0x300000>;
+ no-map;
+ };
+
+ smem@86300000 {
+ compatible = "qcom,smem";
+ reg = <0x0 0x86300000 0x0 0x100000>;
+ no-map;
+
+ hwlocks = <&tcsr_mutex 3>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ };
+
+ hypervisor@86400000 {
+ reg = <0x0 0x86400000 0x0 0x100000>;
+ no-map;
+ };
+
+ tz@86500000 {
+ reg = <0x0 0x86500000 0x0 0x180000>;
+ no-map;
+ };
+
+ reserved@86680000 {
+ reg = <0x0 0x86680000 0x0 0x80000>;
+ no-map;
+ };
+
+ rmtfs@86700000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x86700000 0x0 0xe0000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ };
+
+ rfsa@867e0000 {
+ reg = <0x0 0x867e0000 0x0 0x20000>;
+ no-map;
+ };
+
+ mpss_mem: mpss@86800000 {
+ reg = <0x0 0x86800000 0x0 0x5500000>;
+ no-map;
+ };
+
+ wcnss_mem: wcnss@8bd00000 {
+ reg = <0x0 0x8bd00000 0x0 0x600000>;
+ no-map;
+ };
+
+ venus_mem: venus@8c300000 {
+ reg = <0x0 0x8c300000 0x0 0x800000>;
+ no-map;
+ };
+
+ mba_mem: mba@8cb00000 {
+ no-map;
+ reg = <0x0 0x8cb00000 0x0 0x100000>;
+ };
+ };
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,ipc = <&apcs1_mbox 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests: rpm-requests {
+ compatible = "qcom,rpm-msm8936";
+ qcom,smd-channels = "rpm_requests";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-msm8936", "qcom,rpmcc";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
+
+ rpmpd: power-controller {
+ compatible = "qcom,msm8939-rpmpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmpd_opp_table>;
+
+ rpmpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmpd_opp_ret: opp1 {
+ opp-level = <1>;
+ };
+
+ rpmpd_opp_svs_krait: opp2 {
+ opp-level = <2>;
+ };
+
+ rpmpd_opp_svs_soc: opp3 {
+ opp-level = <3>;
+ };
+
+ rpmpd_opp_nom: opp4 {
+ opp-level = <4>;
+ };
+
+ rpmpd_opp_turbo: opp5 {
+ opp-level = <5>;
+ };
+
+ rpmpd_opp_super_turbo: opp6 {
+ opp-level = <6>;
+ };
+ };
+ };
+ };
+ };
+ };
+
+ smp2p-hexagon {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs1_mbox 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ hexagon_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ };
+ };
+
+ smp2p-wcnss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <451>, <431>;
+
+ interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs1_mbox 18>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <4>;
+
+ wcnss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wcnss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+ };
+
+ smsm {
+ compatible = "qcom,smsm";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qcom,ipc-1 = <&apcs1_mbox 8 13>;
+ qcom,ipc-3 = <&apcs1_mbox 8 19>;
+
+ apps_smsm: apps@0 {
+ reg = <0>;
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smsm: hexagon@1 {
+ reg = <1>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wcnss_smsm: wcnss@6 {
+ reg = <6>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ soc: soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+
+ rng@22000 {
+ compatible = "qcom,prng";
+ reg = <0x00022000 0x200>;
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "core";
+ };
+
+ qfprom: qfprom@5c000 {
+ compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
+ reg = <0x0005c000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tsens_caldata: caldata@a0 {
+ reg = <0xa0 0x5c>;
+ };
+ };
+
+ rpm_msg_ram: sram@60000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0x00060000 0x8000>;
+ };
+
+ bimc: interconnect@400000 {
+ compatible = "qcom,msm8939-bimc";
+ reg = <0x00400000 0x62000>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+ <&rpmcc RPM_SMD_BIMC_A_CLK>;
+ #interconnect-cells = <1>;
+ };
+
+ tsens: thermal-sensor@4a9000 {
+ compatible = "qcom,msm8939-tsens", "qcom,tsens-v0_1";
+ reg = <0x004a9000 0x1000>, /* TM */
+ <0x004a8000 0x1000>; /* SROT */
+ nvmem-cells = <&tsens_caldata>;
+ nvmem-cell-names = "calib";
+ #qcom,sensors = <10>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow";
+ #thermal-sensor-cells = <1>;
+ };
+
+ restart@4ab000 {
+ compatible = "qcom,pshold";
+ reg = <0x004ab000 0x4>;
+ };
+
+ pcnoc: interconnect@500000 {
+ compatible = "qcom,msm8939-pcnoc";
+ reg = <0x00500000 0x11000>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_PCNOC_CLK>,
+ <&rpmcc RPM_SMD_PCNOC_A_CLK>;
+ #interconnect-cells = <1>;
+ };
+
+ snoc: interconnect@580000 {
+ compatible = "qcom,msm8939-snoc";
+ reg = <0x00580000 0x14080>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+ <&rpmcc RPM_SMD_SNOC_A_CLK>;
+ #interconnect-cells = <1>;
+
+ snoc_mm: interconnect-snoc {
+ compatible = "qcom,msm8939-snoc-mm";
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_SYSMMNOC_CLK>,
+ <&rpmcc RPM_SMD_SYSMMNOC_A_CLK>;
+ #interconnect-cells = <1>;
+ };
+ };
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,msm8916-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ gpio-ranges = <&tlmm 0 0 122>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ blsp1_uart1_default: blsp1-uart1-default-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "blsp_uart1";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ blsp1_uart2_default: blsp1-uart2-default-state {
+ pins = "gpio4", "gpio5";
+ function = "blsp_uart2";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_uart2_sleep: blsp1-uart2-sleep-state {
+ pins = "gpio4", "gpio5";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ camera_front_default: camera-front-default-state {
+ pwdn-pins {
+ pins = "gpio33";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ rst-pins {
+ pins = "gpio28";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ mclk1-pins {
+ pins = "gpio27";
+ function = "cam_mclk1";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ camera_rear_default: camera-rear-default-state {
+ pwdn-pins {
+ pins = "gpio34";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ rst-pins {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ mclk0-pins {
+ pins = "gpio26";
+ function = "cam_mclk0";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ cci0_default: cci0-default-state {
+ pins = "gpio29", "gpio30";
+ function = "cci_i2c";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cdc_pdm_lines_default: pdm-lines-default-state {
+ pins = "gpio63", "gpio64", "gpio65", "gpio66",
+ "gpio67", "gpio68";
+ function = "cdc_pdm0";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ cdc_pdm_lines_sleep: pdm-lines-suspend-state {
+ pins = "gpio63", "gpio64", "gpio65", "gpio66",
+ "gpio67", "gpio68";
+ function = "cdc_pdm0";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ cdc_dmic_lines_act: cdc-dmic-lines-on-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "dmic0_clk";
+ drive-strength = <8>;
+ };
+
+ data-pins {
+ pins = "gpio1";
+ function = "dmic0_data";
+ drive-strength = <8>;
+ };
+ };
+
+ cdc_dmic_lines_sus: cdc-dmic-lines-off-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "dmic0_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio1";
+ function = "dmic0_data";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ext-mclk-tlmm-lines-state {
+ ext_mclk_tlmm_lines_act: mclk-lines-on-pins {
+ pins = "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_mclk_tlmm_lines_sus: mclk-lines-off-pins {
+ pins = "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ext-pri-tlmm-lines-state {
+ ext_pri_tlmm_lines_act: ext-pa-on-pins {
+ pins = "gpio113", "gpio114", "gpio115", "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_pri_tlmm_lines_sus: ext-pa-off-pins {
+ pins = "gpio113", "gpio114", "gpio115", "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ext-pri-ws-line-state {
+ ext_pri_ws_act: ext-pa-on-pins {
+ pins = "gpio110";
+ function = "pri_mi2s_ws";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_pri_ws_sus: ext-pa-off-pins {
+ pins = "gpio110";
+ function = "pri_mi2s_ws";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ /* secondary Mi2S */
+ ext-sec-tlmm-lines-state {
+ ext_sec_tlmm_lines_act: tlmm-lines-on-pins {
+ pins = "gpio112", "gpio117", "gpio118", "gpio119";
+ function = "sec_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_sec_tlmm_lines_sus: tlmm-lines-off-pins {
+ pins = "gpio112", "gpio117", "gpio118", "gpio119";
+ function = "sec_mi2s";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ i2c1_default: i2c1-default-state {
+ pins = "gpio2", "gpio3";
+ function = "blsp_i2c1";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c1_sleep: i2c1-sleep-state {
+ pins = "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c2_default: i2c2-default-state {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c2_sleep: i2c2-sleep-state {
+ pins = "gpio6", "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c3_default: i2c3-default-state {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c3";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c3_sleep: i2c3-sleep-state {
+ pins = "gpio10", "gpio11";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c4_default: i2c4-default-state {
+ pins = "gpio14", "gpio15";
+ function = "blsp_i2c4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c4_sleep: i2c4-sleep-state {
+ pins = "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c5_default: i2c5-default-state {
+ pins = "gpio18", "gpio19";
+ function = "blsp_i2c5";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c5_sleep: i2c5-sleep-state {
+ pins = "gpio18", "gpio19";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c6_default: i2c6-default-state {
+ pins = "gpio22", "gpio23";
+ function = "blsp_i2c6";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c6_sleep: i2c6-sleep-state {
+ pins = "gpio22", "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdc1_default_state: sdc1-default-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+ };
+
+ sdc1_sleep_state: sdc1-sleep-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+
+ sdc2_default_state: sdc2-default-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ cd-pins {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_sleep_state: sdc2-sleep-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ cd-pins {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ spi1_default: spi1-default-state {
+ spi-pins {
+ pins = "gpio0", "gpio1", "gpio3";
+ function = "blsp_spi1";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi1_sleep: spi1-sleep-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi2_default: spi2-default-state {
+ spi-pins {
+ pins = "gpio4", "gpio5", "gpio7";
+ function = "blsp_spi2";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio6";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi2_sleep: spi2-sleep-state {
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi3_default: spi3-default-state {
+ spi-pins {
+ pins = "gpio8", "gpio9", "gpio11";
+ function = "blsp_spi3";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio10";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi3_sleep: spi3-sleep-state {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi4_default: spi4-default-state {
+ spi-pins {
+ pins = "gpio12", "gpio13", "gpio15";
+ function = "blsp_spi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio14";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi4_sleep: spi4-sleep-state {
+ pins = "gpio12", "gpio13", "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi5_default: spi5-default-state {
+ spi-pins {
+ pins = "gpio16", "gpio17", "gpio19";
+ function = "blsp_spi5";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi5_sleep: spi5-sleep-state {
+ pins = "gpio16", "gpio17", "gpio18", "gpio19";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi6_default: spi6-default-state {
+ spi-pins {
+ pins = "gpio20", "gpio21", "gpio23";
+ function = "blsp_spi6";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio22";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi6_sleep: spi6-sleep-state {
+ pins = "gpio20", "gpio21", "gpio22", "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ wcnss_pin_a: wcnss-active-state {
+ pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "wcss_wlan";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ gcc: clock-controller@1800000 {
+ compatible = "qcom,gcc-msm8939";
+ reg = <0x01800000 0x80000>;
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+ <&sleep_clk>,
+ <&dsi_phy0 1>,
+ <&dsi_phy0 0>,
+ <&dsi_phy1 1>,
+ <&dsi_phy1 0>,
+ <0>,
+ <0>,
+ <0>;
+ clock-names = "xo",
+ "sleep_clk",
+ "dsi0pll",
+ "dsi0pllbyte",
+ "dsi1pll",
+ "dsi1pllbyte",
+ "ext_mclk",
+ "ext_pri_i2s",
+ "ext_sec_i2s";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ tcsr_mutex: hwlock@1905000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x01905000 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ tcsr: syscon@1937000 {
+ compatible = "qcom,tcsr-msm8916", "syscon";
+ reg = <0x01937000 0x30000>;
+ };
+
+ mdss: display-subsystem@1a00000 {
+ compatible = "qcom,mdss";
+ reg = <0x01a00000 0x1000>,
+ <0x01ac8000 0x3000>;
+ reg-names = "mdss_phys", "vbif_phys";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "vsync";
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <1>;
+ ranges;
+
+ mdp: display-controller@1a01000 {
+ compatible = "qcom,mdp5";
+ reg = <0x01a01000 0x89000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>,
+ <&gcc GCC_MDP_TBU_CLK>,
+ <&gcc GCC_MDP_RT_TBU_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync",
+ "tbu",
+ "tbu_rt";
+
+ iommus = <&apps_iommu 4>;
+
+ interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
+ <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
+ <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
+ interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdp5_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@1a98000 {
+ compatible = "qcom,msm8916-dsi-ctrl",
+ "qcom,mdss-dsi-ctrl";
+ reg = <0x01a98000 0x25c>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE0_CLK>,
+ <&gcc GCC_MDSS_PCLK0_CLK>,
+ <&gcc GCC_MDSS_ESC0_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core";
+ assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+ <&gcc PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy0 0>,
+ <&dsi_phy0 1>;
+
+ phys = <&dsi_phy0>;
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy0: phy@1a98300 {
+ compatible = "qcom,dsi-phy-28nm-lp";
+ reg = <0x01a98300 0xd4>,
+ <0x01a98500 0x280>,
+ <0x01a98780 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "ref";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ dsi1: dsi@1aa0000 {
+ compatible = "qcom,msm8916-dsi-ctrl",
+ "qcom,mdss-dsi-ctrl";
+ reg = <0x01aa0000 0x25c>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE1_CLK>,
+ <&gcc GCC_MDSS_PCLK1_CLK>,
+ <&gcc GCC_MDSS_ESC1_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core";
+ assigned-clocks = <&gcc BYTE1_CLK_SRC>,
+ <&gcc PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy1 0>,
+ <&dsi_phy1 1>;
+ phys = <&dsi_phy1>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi1_in: endpoint {
+ remote-endpoint = <&mdp5_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy1: phy@1aa0300 {
+ compatible = "qcom,dsi-phy-28nm-lp";
+ reg = <0x01aa0300 0xd4>,
+ <0x01aa0500 0x280>,
+ <0x01aa0780 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "ref";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ gpu@1c00000 {
+ compatible = "qcom,adreno-405.0", "qcom,adreno";
+ reg = <0x01c00000 0x10000>;
+ reg-names = "kgsl_3d0_reg_memory";
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "kgsl_3d0_irq";
+ clock-names = "core",
+ "iface",
+ "mem",
+ "mem_iface",
+ "alt_mem_iface",
+ "gfx3d",
+ "rbbmtimer";
+ clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
+ <&gcc GCC_OXILI_AHB_CLK>,
+ <&gcc GCC_OXILI_GMEM_CLK>,
+ <&gcc GCC_BIMC_GFX_CLK>,
+ <&gcc GCC_BIMC_GPU_CLK>,
+ <&gcc GFX3D_CLK_SRC>,
+ <&gcc GCC_OXILI_TIMER_CLK>;
+ power-domains = <&gcc OXILI_GDSC>;
+ operating-points-v2 = <&opp_table>;
+ iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
+
+ opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-550000000 {
+ opp-hz = /bits/ 64 <550000000>;
+ };
+
+ opp-465000000 {
+ opp-hz = /bits/ 64 <465000000>;
+ };
+
+ opp-400000000 {
+ opp-hz = /bits/ 64 <400000000>;
+ };
+
+ opp-220000000 {
+ opp-hz = /bits/ 64 <220000000>;
+ };
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ };
+ };
+ };
+
+ apps_iommu: iommu@1ef0000 {
+ compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
+ reg = <0x01ef0000 0x3000>;
+ ranges = <0 0x1e20000 0x40000>;
+ clocks = <&gcc GCC_SMMU_CFG_CLK>,
+ <&gcc GCC_APSS_TCU_CLK>;
+ clock-names = "iface", "bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #iommu-cells = <1>;
+ qcom,iommu-secure-id = <17>;
+
+ /* mdp_0: */
+ iommu-ctx@4000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x4000 0x1000>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ /* venus_ns: */
+ iommu-ctx@5000 {
+ compatible = "qcom,msm-iommu-v1-sec";
+ reg = <0x5000 0x1000>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ gpu_iommu: iommu@1f08000 {
+ compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
+ ranges = <0 0x1f08000 0x10000>;
+ clocks = <&gcc GCC_SMMU_CFG_CLK>,
+ <&gcc GCC_GFX_TCU_CLK>,
+ <&gcc GCC_GFX_TBU_CLK>;
+ clock-names = "iface", "bus", "tbu";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #iommu-cells = <1>;
+ qcom,iommu-secure-id = <18>;
+
+ /* gfx3d_user: */
+ iommu-ctx@1000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x1000 0x1000>;
+ interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ /* gfx3d_priv: */
+ iommu-ctx@2000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x2000 0x1000>;
+ interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ spmi_bus: spmi@200f000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0200f000 0x001000>,
+ <0x02400000 0x400000>,
+ <0x02c00000 0x400000>,
+ <0x03800000 0x200000>,
+ <0x0200a000 0x002100>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ mpss: remoteproc@4080000 {
+ compatible = "qcom,msm8916-mss-pil";
+ reg = <0x04080000 0x100>,
+ <0x04020000 0x040>;
+
+ reg-names = "qdsp6", "rmb";
+
+ interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+ <&gcc GCC_BOOT_ROM_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "bus", "mem", "xo";
+
+ power-domains = <&rpmpd MSM8939_VDDMDCX>,
+ <&rpmpd MSM8939_VDDMX>;
+ power-domain-names = "cx", "mx";
+
+ qcom,smem-states = <&hexagon_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ resets = <&scm 0>;
+ reset-names = "mss_restart";
+
+ qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>;
+
+ status = "disabled";
+
+ mba {
+ memory-region = <&mba_mem>;
+ };
+
+ mpss {
+ memory-region = <&mpss_mem>;
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,smd-edge = <0>;
+ mboxes = <&apcs1_mbox 12>;
+ qcom,remote-pid = <1>;
+
+ label = "hexagon";
+ };
+ };
+
+ sound: sound@7702000 {
+ compatible = "qcom,apq8016-sbc-sndcard";
+ reg = <0x07702000 0x4>,
+ <0x07702004 0x4>;
+ reg-names = "mic-iomux", "spkr-iomux";
+ status = "disabled";
+ };
+
+ lpass: audio-controller@7708000 {
+ compatible = "qcom,apq8016-lpass-cpu";
+ reg = <0x07708000 0x10000>;
+ reg-names = "lpass-lpaif";
+ interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "lpass-irq-lpaif";
+ clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
+ <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>;
+ clock-names = "ahbix-clk",
+ "mi2s-bit-clk0",
+ "mi2s-bit-clk1",
+ "mi2s-bit-clk2",
+ "mi2s-bit-clk3",
+ "pcnoc-mport-clk",
+ "pcnoc-sway-clk";
+ #sound-dai-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ lpass_codec: audio-codec@771c000 {
+ compatible = "qcom,msm8916-wcd-digital-codec";
+ reg = <0x0771c000 0x400>;
+ clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+ <&gcc GCC_CODEC_DIGCODEC_CLK>;
+ clock-names = "ahbix-clk", "mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ sdhc_1: mmc@7824900 {
+ compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
+ reg = <0x07824900 0x11c>, <0x07824000 0x800>;
+ reg-names = "hc", "core";
+
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "core", "xo";
+ resets = <&gcc GCC_SDCC1_BCR>;
+ mmc-ddr-1_8v;
+ bus-width = <8>;
+ non-removable;
+ status = "disabled";
+ };
+
+ sdhc_2: mmc@7864900 {
+ compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
+ reg = <0x07864900 0x11c>, <0x07864000 0x800>;
+ reg-names = "hc", "core";
+
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "core", "xo";
+ resets = <&gcc GCC_SDCC2_BCR>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ blsp_dma: dma-controller@7884000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07884000 0x23000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+ blsp1_uart1: serial@78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ pinctrl-1 = <&blsp1_uart1_sleep>;
+ status = "disabled";
+ };
+
+ blsp1_uart2: serial@78b0000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b0000 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart2_default>;
+ pinctrl-1 = <&blsp1_uart2_sleep>;
+ status = "disabled";
+ };
+
+ blsp_i2c1: i2c@78b5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b5000 0x500>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_default>;
+ pinctrl-1 = <&i2c1_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi1: spi@78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b5000 0x500>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi1_default>;
+ pinctrl-1 = <&spi1_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c2: i2c@78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b6000 0x500>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c2_default>;
+ pinctrl-1 = <&i2c2_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi2: spi@78b6000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b6000 0x500>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi2_default>;
+ pinctrl-1 = <&spi2_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c3: i2c@78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b7000 0x500>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c3_default>;
+ pinctrl-1 = <&i2c3_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi3: spi@78b7000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b7000 0x500>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi3_default>;
+ pinctrl-1 = <&spi3_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c4: i2c@78b8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b8000 0x500>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c4_default>;
+ pinctrl-1 = <&i2c4_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi4: spi@78b8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b8000 0x500>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi4_default>;
+ pinctrl-1 = <&spi4_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c5: i2c@78b9000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b9000 0x500>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c5_default>;
+ pinctrl-1 = <&i2c5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi5: spi@78b9000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b9000 0x500>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi5_default>;
+ pinctrl-1 = <&spi5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c6: i2c@78ba000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078ba000 0x500>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c6_default>;
+ pinctrl-1 = <&i2c6_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi6: spi@78ba000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078ba000 0x500>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi6_default>;
+ pinctrl-1 = <&spi6_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usb: usb@78d9000 {
+ compatible = "qcom,ci-hdrc";
+ reg = <0x078d9000 0x200>,
+ <0x078d9200 0x200>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+ <&gcc GCC_USB_HS_SYSTEM_CLK>;
+ clock-names = "iface", "core";
+ assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+ assigned-clock-rates = <80000000>;
+ resets = <&gcc GCC_USB_HS_BCR>;
+ reset-names = "core";
+ #reset-cells = <1>;
+ phy_type = "ulpi";
+ dr_mode = "otg";
+ ahb-burst-config = <0>;
+ phy-names = "usb-phy";
+ phys = <&usb_hs_phy>;
+ status = "disabled";
+
+ ulpi {
+ usb_hs_phy: phy {
+ compatible = "qcom,usb-hs-phy-msm8916",
+ "qcom,usb-hs-phy";
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "sleep";
+ resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+ reset-names = "phy", "por";
+ #phy-cells = <0>;
+ qcom,init-seq = /bits/ 8 <0x0 0x44
+ 0x1 0x6b 0x2 0x24 0x3 0x13>;
+ };
+ };
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>,
+ <0x0b001000 0x1000>, <0x0b004000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ apcs1_mbox: mailbox@b011000 {
+ compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+ reg = <0x0b011000 0x1000>;
+ clocks = <&a53pll_c1>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "pll", "aux", "ref";
+ #clock-cells = <0>;
+ assigned-clocks = <&apcs2>;
+ assigned-clock-rates = <297600000>;
+ #mbox-cells = <1>;
+ };
+
+ a53pll_c1: clock@b016000 {
+ compatible = "qcom,msm8939-a53pll";
+ reg = <0x0b016000 0x40>;
+ #clock-cells = <0>;
+ };
+
+ acc0: clock-controller@b088000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b088000 0x1000>;
+ };
+
+ saw0: power-manager@b089000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b089000 0x1000>;
+ };
+
+ acc1: clock-controller@b098000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b098000 0x1000>;
+ };
+
+ saw1: power-manager@b099000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b099000 0x1000>;
+ };
+
+ acc2: clock-controller@b0a8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b0a8000 0x1000>;
+ };
+
+ saw2: power-manager@b0a9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b0a9000 0x1000>;
+ };
+
+ acc3: clock-controller@b0b8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b0b8000 0x1000>;
+ };
+
+ saw3: power-manager@b0b9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b0b9000 0x1000>;
+ };
+
+ apcs0_mbox: mailbox@b111000 {
+ compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+ reg = <0x0b111000 0x1000>;
+ clocks = <&a53pll_c0>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "pll", "aux", "ref";
+ #clock-cells = <0>;
+ #mbox-cells = <1>;
+ };
+
+ a53pll_c0: clock@b116000 {
+ compatible = "qcom,msm8939-a53pll";
+ reg = <0x0b116000 0x40>;
+ #clock-cells = <0>;
+ };
+
+ acc4: clock-controller@b188000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b188000 0x1000>;
+ };
+
+ saw4: power-manager@b189000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b189000 0x1000>;
+ };
+
+ acc5: clock-controller@b198000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b198000 0x1000>;
+ };
+
+ saw5: power-manager@b199000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b199000 0x1000>;
+ };
+
+ acc6: clock-controller@b1a8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b1a8000 0x1000>;
+ };
+
+ saw6: power-manager@b1a9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b1a9000 0x1000>;
+ };
+
+ acc7: clock-controller@b1b8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b1b8000 0x1000>;
+ };
+
+ saw7: power-manager@b1b9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b1b9000 0x1000>;
+ };
+
+ a53pll_cci: clock@b1d0000 {
+ compatible = "qcom,msm8939-a53pll";
+ reg = <0x0b1d0000 0x40>;
+ #clock-cells = <0>;
+ };
+
+ apcs2: mailbox@b1d1000 {
+ compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+ reg = <0x0b1d1000 0x1000>;
+ clocks = <&a53pll_cci>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "pll", "aux", "ref";
+ #clock-cells = <0>;
+ #mbox-cells = <1>;
+ };
+
+ timer@b020000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b020000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ frame@b021000 {
+ reg = <0x0b021000 0x1000>,
+ <0x0b022000 0x1000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <0>;
+ };
+
+ frame@b023000 {
+ reg = <0x0b023000 0x1000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <1>;
+ status = "disabled";
+ };
+
+ frame@b024000 {
+ reg = <0x0b024000 0x1000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <2>;
+ status = "disabled";
+ };
+
+ frame@b025000 {
+ reg = <0x0b025000 0x1000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <3>;
+ status = "disabled";
+ };
+
+ frame@b026000 {
+ reg = <0x0b026000 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <4>;
+ status = "disabled";
+ };
+
+ frame@b027000 {
+ reg = <0x0b027000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <5>;
+ status = "disabled";
+ };
+
+ frame@b028000 {
+ reg = <0x0b028000 0x1000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <6>;
+ status = "disabled";
+ };
+ };
+
+ pronto: remoteproc@a204000 {
+ compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+ reg = <0x0a204000 0x2000>,
+ <0x0a202000 0x1000>,
+ <0x0a21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+
+ interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+ memory-region = <&wcnss_mem>;
+
+ power-domains = <&rpmpd MSM8939_VDDCX>,
+ <&rpmpd MSM8939_VDDMX_AO>;
+ power-domain-names = "cx", "mx";
+
+ qcom,smem-states = <&wcnss_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+
+ status = "disabled";
+
+ iris {
+ compatible = "qcom,wcn3620";
+ clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+ clock-names = "xo";
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 142 1>;
+ qcom,ipc = <&apcs1_mbox 8 17>;
+ qcom,smd-edge = <6>;
+ qcom,remote-pid = <4>;
+
+ label = "pronto";
+
+ wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ qcom,mmio = <&pronto>;
+
+ bluetooth {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wifi {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ qcom,smem-states = <&apps_smsm 10>,
+ <&apps_smsm 9>;
+ qcom,smem-state-names = "tx-enable",
+ "tx-rings-empty";
+ };
+ };
+ };
+ };
+ };
+
+ thermal_zones: thermal-zones {
+ cpu0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 5>;
+
+ trips {
+ cpu0_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu0_crit: trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu0_alert>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 6>;
+
+ trips {
+ cpu1_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu1_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu1_alert>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 7>;
+
+ trips {
+ cpu2_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu2_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu2_alert>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu3-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 8>;
+
+ trips {
+ cpu3_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu3_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu3_alert>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu4567-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 9>;
+
+ trips {
+ cpu4567_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu4567_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu4567_alert>;
+ cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ gpu_alert0: trip-point0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ gpu_crit: gpu_crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ modem1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 0>;
+
+ trips {
+ modem1_alert0: trip-point0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ modem2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 2>;
+
+ trips {
+ modem2_alert0: trip-point0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ camera-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 1>;
+
+ trips {
+ cam_alert0: trip-point0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ /* Dummy power-supply for our non-psci cpu@X defintions */
+ vreg_dummy: regulator-dummy {
+ #power-domain-cells = <0>;
+ };
+};
--
2.38.1
