Re: [PATCH 1/2] soc: qcom: dcc: Fix examples list on /sys/kernel/debug/dcc/.../[list-number]/config documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 12/30/2022 7:20 PM, Bagas Sanjaya wrote:
kernel test robot reported htmldocs warnings:

Documentation/ABI/testing/debugfs-driver-dcc:34: WARNING: Unexpected indentation.
Documentation/ABI/testing/debugfs-driver-dcc:34: WARNING: Block quote ends without a blank line; unexpected unindent.

Fix these by fixing numbered list syntax on description of
/sys/kernel/debug/dcc/.../[list-number]/config, including adding blank line
separators as appropriate.

Link: https://lore.kernel.org/linux-doc/202212300426.eMLsZsvA-lkp@xxxxxxxxx/
Fixes: 4cbe60cf5ad622 ("soc: qcom: dcc: Add driver support for Data Capture and Compare unit(DCC)")
Reported-by: kernel test robot <lkp@xxxxxxxxx>
Signed-off-by: Bagas Sanjaya <bagasdotme@xxxxxxxxx>
---
  Documentation/ABI/testing/debugfs-driver-dcc | 63 +++++++++++++-------
  1 file changed, 41 insertions(+), 22 deletions(-)

diff --git a/Documentation/ABI/testing/debugfs-driver-dcc b/Documentation/ABI/testing/debugfs-driver-dcc
index a4680950205931..a00f4502885b58 100644
--- a/Documentation/ABI/testing/debugfs-driver-dcc
+++ b/Documentation/ABI/testing/debugfs-driver-dcc
@@ -44,35 +44,54 @@ Description:
  		example user can jump to list x only after list y is
  		configured and enabled. The format for entering all
  		types of instructions are explained in examples as
-		follows.
-		Example:
-	         i)Read Type Instruction
+		follows:
+
+	        i) Read Type Instruction
+
  		   echo R <1> <2> <3> >/sys/kernel/debug/dcc/../[list-number]/config
+
  		   1->Address to be considered for reading the value.
+
  		   2->The word count of the addresses, read n words
  		      starting from address <1>. Each word is of 32 bits.
  		      If not entered 1 is considered.
+
  		   3->Can be 'apb' or 'ahb' which indicates if it is apb or ahb
  		      bus respectively. If not entered ahb is considered.
-		ii)Write Type Instruction
-		   echo W <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
-		   1->Address to be considered for writing the value.
-		   2->The value that needs to be written at the location.
-		   3->Can be a 'apb' or 'ahb' which indicates if it is apb or ahb
-		      but respectively.
-	       iii)Read Modify Write type instruction
-		   echo RW <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
-		   1->The address which needs to be considered for read then write.
-		   2->The value that needs to be written on the address.
-		   3->The mask of the value to be written.
-		iv)Loop Type Instruction
-		   echo L <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
-		   1->The loop count, the number of times the value of the addresses will be
-		      captured.
-		   2->The address count, total number of addresses to be entered in this
-		      instruction.
-		   3->The series of addresses to be entered separated by a space like <addr1>
-		      <addr2>... and so on.
+
+		ii) Write Type Instruction
+
+		    echo W <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    1->Address to be considered for writing the value.
+
+		    2->The value that needs to be written at the location.
+
+		    3->Can be a 'apb' or 'ahb' which indicates if it is apb or ahb
+		       but respectively.
+
+	        iii) Read Modify Write type instruction
+
+		     echo RW <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		     1->The address which needs to be considered for read then write.
+
+		     2->The value that needs to be written on the address.
+
+		     3->The mask of the value to be written.
+
+		iv) Loop Type Instruction
+
+		    echo L <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    1->The loop count, the number of times the value of the addresses will be
+		       captured.
+
+		    2->The address count, total number of addresses to be entered in this
+		       instruction.
+
+		    3->The series of addresses to be entered separated by a space like <addr1>
+		       <addr2>... and so on.
What: /sys/kernel/debug/dcc/.../[list-number]/enable
  Date:           December 2022

Acked-by:Souradeep Chowdhury <quic_schowdhu@xxxxxxxxxxx>



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux