On 14/12/2022 21:31, Bhupesh Sharma wrote:
> Add USB superspeed qmp phy node to dtsi.
> Make sure that the oneplus board dts (which includes the
> sm4250.dtsi) continues to work as intended.
>
> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@xxxxxxxxxx>
> ---
> .../boot/dts/qcom/sm4250-oneplus-billie2.dts | 3 ++
> arch/arm64/boot/dts/qcom/sm6115.dtsi | 38 ++++++++++++++++++-
> 2 files changed, 39 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
> index 3f39f25e0721e..4f0d65574448b 100644
> --- a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
> +++ b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
> @@ -232,6 +232,9 @@ &usb {
> &usb_dwc3 {
> maximum-speed = "high-speed";
> dr_mode = "peripheral";
> +
> + phys = <&usb_hsphy>;
> + phy-names = "usb2-phy";
> };
>
> &usb_hsphy {
> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> index e4ce135264f3d..15f311dcd289f 100644
> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> @@ -579,6 +579,40 @@ usb_hsphy: phy@1613000 {
> status = "disabled";
> };
>
> + usb_qmpphy: phy@1615000 {
> + compatible = "qcom,sm6115-qmp-usb3-phy";
> + reg = <0x01615000 0x200>;
> + clocks = <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> + <&gcc GCC_AHB2PHY_USB_CLK>;
> + clock-names = "com_aux",
> + "ref",
> + "cfg_ahb";
> + resets = <&gcc GCC_USB3_PHY_PRIM_SP0_BCR>,
> + <&gcc GCC_USB3PHY_PHY_PRIM_SP0_BCR>;
> + reset-names = "phy", "phy_phy";
> + status = "disabled";
> + #clock-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + usb_ssphy: phy@1615200 {
> + reg = <0x01615200 0x200>,
> + <0x01615400 0x200>,
> + <0x01615c00 0x400>,
> + <0x01615600 0x200>,
> + <0x01615800 0x200>,
> + <0x01615a00 0x100>;
> + #phy-cells = <0>;
> + #clock-cells = <1>;
> + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_phy_pipe_clk_src";
> + };
> + };
> +
> +
Still two blank lines.
Best regards,
Krzysztof
