Include the dtsi to use a single pmic descriptions.
Both sa8295p-adp and sa8540p-adp have the same spmi pmic apparently.
Signed-off-by: Eric Chanudet <echanude@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 79 +-----------------------
1 file changed, 1 insertion(+), 78 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
index 84cb6f3eeb56..889259df3287 100644
--- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
@@ -11,6 +11,7 @@
#include <dt-bindings/spmi/spmi.h>
#include "sa8540p.dtsi"
+#include "pm8450a.dtsi"
/ {
model = "Qualcomm SA8295P ADP";
@@ -260,84 +261,6 @@ &remoteproc_nsp1 {
status = "okay";
};
-&spmi_bus {
- pm8450a: pmic@0 {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0x0 SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- rtc@6000 {
- compatible = "qcom,pm8941-rtc";
- reg = <0x6000>;
- reg-names = "rtc", "alarm";
- interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
- wakeup-source;
- };
-
- pm8450a_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
- reg = <0xc000>;
- gpio-controller;
- gpio-ranges = <&pm8450a_gpios 0 0 10>;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-
- pm8450c: pmic@4 {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0x4 SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450c_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
- reg = <0xc000>;
- gpio-controller;
- gpio-ranges = <&pm8450c_gpios 0 0 10>;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-
- pm8450e: pmic@8 {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0x8 SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450e_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
- reg = <0xc000>;
- gpio-controller;
- gpio-ranges = <&pm8450e_gpios 0 0 10>;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-
- pm8450g: pmic@c {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0xc SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450g_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
- reg = <0xc000>;
- gpio-controller;
- gpio-ranges = <&pm8450g_gpios 0 0 10>;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-};
-
&ufs_mem_hc {
reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
--
2.38.1
