[PATCH v3 8/9] arm64: dts: qcom: msm8953: Add device tree for Xiaomi Redmi 5 Plus

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Eugene Lepshy <fekz115@xxxxxxxxx>

Add device tree for the Xiaomi Redmi 5 Plus (vince) smartphone. This
device is based on Snapdragon 625 (msm8953) SoC.

Signed-off-by: Eugene Lepshy <fekz115@xxxxxxxxx>
Co-developed-by: Gianluca Boiano <morf3089@xxxxxxxxx>
Signed-off-by: Gianluca Boiano <morf3089@xxxxxxxxx>
Signed-off-by: Luca Weiss <luca@xxxxxxxxx>
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/Makefile                 |   1 +
 arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts | 361 ++++++++++++++++++++++
 2 files changed, 362 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 054dfbe820d9..995973d3960a 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-potter.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-daisy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-mido.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-tissot.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-vince.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8956-sony-xperia-loire-kugo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8956-sony-xperia-loire-suzu.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-lg-bullhead-rev-10.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts b/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts
new file mode 100644
index 000000000000..b5be55034fd3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Eugene Lepshy <fekz115@xxxxxxxxx>
+ * Copyright (c) 2022, Gianluca Boiano <morf3089@xxxxxxxxx>
+ */
+/dts-v1/;
+
+#include "msm8953.dtsi"
+#include "pm8953.dtsi"
+#include "pmi8950.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/delete-node/ &adsp_fw_mem;
+/delete-node/ &cont_splash_mem;
+/delete-node/ &qseecom_mem;
+/delete-node/ &wcnss_fw_mem;
+
+/ {
+	model = "Xiaomi Redmi 5 Plus";
+	compatible = "xiaomi,vince", "qcom,msm8953";
+	chassis-type = "handset";
+	qcom,msm-id = <293 0>;
+	qcom,board-id= <0x1000b 0x08>;
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_key_default>;
+
+		key-volume-up {
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reserved-memory {
+		qseecom_mem: qseecom@84a00000 {
+			reg = <0x0 0x84a00000 0x0 0x1900000>;
+			no-map;
+		};
+
+		cont_splash_mem: cont-splash@90001000 {
+			reg = <0x0 0x90001000 0x0 (1080 * 2160 * 3)>;
+			no-map;
+		};
+
+		adsp_fw_mem: adsp@8d600000 {
+			reg = <0x0 0x8d600000 0x0 0x1200000>;
+			no-map;
+		};
+
+		wcnss_fw_mem: wcnss@8e800000 {
+			reg = <0x0 0x8e800000 0x0 0x700000>;
+			no-map;
+		};
+
+		ramoops@9ff00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x9ff00000 0x0 0x100000>;
+			record-size = <0x1000>;
+			console-size = <0x80000>;
+			ftrace-size = <0x1000>;
+			pmsg-size = <0x8000>;
+		};
+	};
+
+	/*
+	 * We bitbang on &i2c_4 because BLSP is protected by TZ as sensors are
+	 * normally proxied via ADSP firmware. GPIOs aren't protected.
+	 */
+	i2c-sensors {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>; /* ~100 kHz */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imu@6a {
+			compatible = "st,lsm6dsl";
+			reg = <0x6a>;
+			vdd-supply = <&pm8953_l10>;
+			vddio-supply = <&pm8953_l6>;
+			mount-matrix = "1", "0", "0",
+					"0", "-1", "0",
+					"0", "0", "1";
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&hsusb_phy {
+	vdd-supply = <&pm8953_l3>;
+	vdda-pll-supply = <&pm8953_l7>;
+	vdda-phy-dpdm-supply = <&pm8953_l13>;
+
+	status = "okay";
+};
+
+&i2c_2 {
+	status = "okay";
+
+	led-controller@45 {
+		compatible = "awinic,aw2013";
+		reg = <0x45>;
+
+		vcc-supply = <&pm8953_l10>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-max-microamp = <5000>;
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+		};
+	};
+};
+
+&i2c_3 {
+	status = "okay";
+
+	touchscreen@20 {
+		reg = <0x20>;
+		compatible = "syna,rmi4-i2c";
+		interrupts-parent = <&tlmm>;
+		interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8953_l10>;
+		vio-supply = <&pm8953_l6>;
+
+		pinctrl-names = "init", "suspend";
+		pinctrl-0 = <&ts_reset_active &ts_int_active>;
+		pinctrl-1 = <&ts_reset_suspend &ts_int_suspend>;
+		syna,reset-delay-ms = <200>;
+		syna,startup-delay-ms = <500>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,rezero-wait-ms = <20>;
+			syna,sensor-type = <1>;
+			touchscreen-x-mm = <68>;
+			touchscreen-y-mm = <122>;
+		};
+	};
+};
+
+&pm8953_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pmi8950_wled {
+	qcom,current-limit-microamp = <20000>;
+	qcom,ovp-millivolt = <29600>;
+	qcom,num-strings = <2>;
+	qcom,external-pfet;
+	qcom,cabc;
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8953-regulators";
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_l1-supply = <&pm8953_s3>;
+		vdd_l2_l3-supply = <&pm8953_s3>;
+		vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
+		vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
+		vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
+
+		pm8953_s1: s1 {
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <1156000>;
+		};
+
+		pm8953_s3: s3 {
+			regulator-min-microvolt = <984000>;
+			regulator-max-microvolt = <1224000>;
+		};
+
+		pm8953_s4: s4 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8953_l1: l1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		pm8953_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8953_l3: l3 {
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+		};
+
+		pm8953_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1900000>;
+		};
+
+		pm8953_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8953_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8953_l10: l10 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l11: l11 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8953_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8953_l13: l13 {
+			regulator-min-microvolt = <3125000>;
+			regulator-max-microvolt = <3125000>;
+		};
+
+		pm8953_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l17: l17 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l19: l19 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1380000>;
+		};
+
+		pm8953_l22: l22 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8953_l23: l23 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1225000>;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8953_l8>;
+	vqmmc-supply = <&pm8953_l5>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8953_l11>;
+	vqmmc-supply = <&pm8953_l12>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <16 4>, <135 4>;
+
+	ts_reset_active: ts-reset-active-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_reset_suspend: ts-reset-suspend-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	ts_int_active: ts-int-active-state {
+		pins = "gpio65";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_int_suspend: ts-int-suspend-state {
+		pins = "gpio65";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&uart_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart_console_active>;
+
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+};

-- 
b4 0.10.1



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux