Re: [RESEND PATCH 2/2] arm64: dts: qcom: sdm632-fairphone-fp3: Add NFC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 29.11.2022 19:31, Luca Weiss wrote:
> On Dienstag, 29. November 2022 14:29:36 CET Konrad Dybcio wrote:
>> On 28.11.2022 18:37, Luca Weiss wrote:
>>> Configure the node for the NQ310 chip found on this device, which is
>>> compatible with generic nxp-nci-i2c driver.
>>>
>>> Signed-off-by: Luca Weiss <luca@xxxxxxxxx>
>>> ---
>>> RESEND to fix Cc
>>>
>>>  arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts | 15 +++++++++++++++
>>>  1 file changed, 15 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
>>> b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts index
>>> 2920504461d3..fde93cbcd180 100644
>>> --- a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
>>> +++ b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
>>> @@ -63,6 +63,21 @@ touchscreen@48 {
>>>
>>>  	};
>>>  
>>>  };
>>>
>>> +&i2c_5 {
>>> +	status = "okay";
>>> +
>>> +	nfc@28 {
>>> +		compatible = "nxp,nq310", "nxp,nxp-nci-i2c";
>>
>> Unless there was some binding change (that was not emailed to me with
>> this email, I only got 2/2), only "nxp,nxp-nci-i2c" and
>> "nxp,pn547", "nxp,nxp-nci-i2c" are allowed.
> 
> Yes, I've added the double compatible to the yaml.
> https://lore.kernel.org/lkml/20221128173744.833018-1-luca@xxxxxxxxx/
Ok, this looks good then.

Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>


> 
> I'll try to work on my Cc-script setup, currently it adds the output of 
> get_maintainers.pl for each patch (and adds all for the cover letter), which 
> is based on some script I found a while ago online.
> 
> Is there like a recommended way to put all people in Cc for a series, I'm not 
> aware of anything at least...
> 
> Perhaps I'll look into b4 for sending patches, that seems to have some goodies 
> there.
Check out this reply from Rob Herring here https://lore.kernel.org/lkml/CAL_JsqLubWBr2W3xZPsuPLOGav7CFgBdH=aCfT22F_m0_cx3cQ@xxxxxxxxxxxxxx/

Konrad
> 
> Regards
> Luca
> 
>>
>> The node looks good though.
>>
>> Konrad
>>
>>> +		reg = <0x28>;
>>> +
>>> +		interrupt-parent = <&tlmm>;
>>> +		interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
>>> +
>>> +		enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
>>> +		firmware-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
>>> +	};
>>> +};
>>> +
>>>
>>>  &pm8953_resin {
>>>  
>>>  	status = "okay";
>>>  	linux,code = <KEY_VOLUMEDOWN>;
> 
> 
> 
> 



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux