On 21.11.2022 01:47, Lin, Meng-Bo wrote: > Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released > in 2014. > > Note: The original firmware from Acer can only boot 32-bit kernels. > To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware > with EDL, e.g. taken from the DragonBoard 410c. This works because Acer > didn't set up (firmware) secure boot. > > Add a device tree for with initial support for: > > - GPIO keys > - pm8916-vibrator > - SDHCI (internal and external storage) > - USB Device Mode > - UART > - WCNSS (WiFi/BT) > - Regulators > > Signed-off-by: Lin, Meng-Bo <linmengbo0689@xxxxxxxxxxxxxx> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx> Konrad > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8916-acer-a1-724.dts | 217 ++++++++++++++++++ > 2 files changed, 218 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index afe496a93f94..f38a20074013 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts > new file mode 100644 > index 000000000000..67187673364c > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts > @@ -0,0 +1,217 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8916-pm8916.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/* > + * NOTE: The original firmware from Acer can only boot 32-bit kernels. > + * To boot this device tree using arm64 it is necessary to flash 64-bit > + * TZ/HYP firmware (e.g. taken from the DragonBoard 410c). > + * See https://wiki.postmarketos.org/wiki/Acer_Iconia_Talk_S_(acer-a1-724) > + * for suggested installation instructions. > + */ > + > +/ { > + model = "Acer Iconia Talk S A1-724"; > + compatible = "acer,a1-724", "qcom,msm8916"; > + chassis-type = "tablet"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys_default>; > + > + label = "GPIO Buttons"; > + > + button-volume-up { > + label = "Volume Up"; > + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + usb_id: usb-id { > + compatible = "linux,extcon-usb-gpio"; > + id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_id_default>; > + }; > +}; > + > +&blsp1_uart2 { > + status = "okay"; > +}; > + > +&pm8916_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&pm8916_vib { > + status = "okay"; > +}; > + > +&pronto { > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; > + > + status = "okay"; > +}; > + > +&sdhc_2 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; > + > + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>; > + > + status = "okay"; > +}; > + > +&usb { > + extcon = <&usb_id>, <&usb_id>; > + status = "okay"; > +}; > + > +&usb_hs_phy { > + extcon = <&usb_id>; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + l1 { > + regulator-min-microvolt = <1225000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l8 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l10 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-allow-set-load; > + regulator-system-load = <200000>; > + }; > + > + l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l16 { > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&msmgpio { > + gpio_keys_default: gpio-keys-default-state { > + pins = "gpio107"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + usb_id_default: usb-id-default-state { > + pins = "gpio110"; > + function = "gpio"; > + > + drive-strength = <8>; > + bias-pull-up; > + }; > +};
