Re: [PATCH v3 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 16/11/2022 11:13, Krzysztof Kozlowski wrote:
From: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>

Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
LPASS pin controller.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>

---

Changes since v2:
1. Use lower-case hex.

Changes since v1:
1. Whitespace cleanups.
2. Correct include - do not use deprecated one.
---
  arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
  1 file changed, 295 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 4b0a1eee8bd9..747440d0445a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -15,6 +15,7 @@
  #include <dt-bindings/interconnect/qcom,sm8450.h>
  #include <dt-bindings/soc/qcom,gpr.h>
  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
  #include <dt-bindings/thermal/thermal.h>
/ {
@@ -2097,6 +2098,212 @@ compute-cb@3 {
  			};
  		};
+ wsa2macro: codec@31e0000 {
+			compatible = "qcom,sm8450-lpass-wsa-macro";
+			reg = <0 0x031e0000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "wsa2-mclk";
+			#sound-dai-cells = <1>;
I think I'm being a bit too picky, but #-cells could go as the last bunch of properties.


+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wsa2_swr_active>;
+		};
+
+		/* WSA2 */
+		swr4: soundwire-controller@31f0000 {
+			reg = <0 0x031f0000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&wsa2macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <2>;
+			qcom,dout-ports = <6>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
+			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-lane-control =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		rxmacro: codec@3200000 {
+			compatible = "qcom,sm8450-lpass-rx-macro";
+			reg = <0 0x3200000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&rx_swr_active>;
+		};
+
+		swr1: soundwire-controller@3210000 {
+			reg = <0 0x3210000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
Some nodes have reg and compatible flipped.

+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rxmacro>;
+			clock-names = "iface";
+			label = "RX";
+			qcom,din-ports = <0>;
+			qcom,dout-ports = <5>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
+			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		txmacro: codec@3220000 {
+			compatible = "qcom,sm8450-lpass-tx-macro";
+			reg = <0 0x3220000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+					   <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&tx_swr_active>;
+		};
+
+		wsamacro: codec@3240000 {
+			compatible = "qcom,sm8450-lpass-wsa-macro";
+			reg = <0 0x03240000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+					  <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>, <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wsa_swr_active>;
+		};
+
+		/* WSA */
+		swr0: soundwire-controller@3250000 {
+			reg = <0 0x03250000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&wsamacro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <2>;
+			qcom,dout-ports = <6>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
+			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,ports-lane-control =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+			qcom,port-offset = <1>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		swr2: soundwire-controller@33b0000 {
+			reg = <0 0x33b0000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.7.0";
+			interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "core", "wake";
+
+			clocks = <&vamacro>;
+			clock-names = "iface";
+			label = "TX";
+
+			qcom,din-ports = <4>;
+			qcom,dout-ports = <0>;
+			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x01 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x01 0x01>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00 0x00>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0xff 0xff>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff>;
+			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x02 0x00 0x00>;
+			qcom,port-offset = <1>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		vamacro: codec@33f0000 {
+			compatible = "qcom,sm8450-lpass-va-macro";
+			reg = <0 0x033f0000 0 0x1000>;
+			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			clock-names = "mclk", "macro", "dcodec", "npl";
+			assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			assigned-clock-rates = <19200000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "fsgen";
+			#sound-dai-cells = <1>;
+		};
+
  		remoteproc_adsp: remoteproc@30000000 {
  			compatible = "qcom,sm8450-adsp-pas";
  			reg = <0 0x030000000 0 0x100>;
@@ -3030,6 +3237,91 @@ qup_uart20_default: qup-uart20-default-state {
}; + lpass_tlmm: pinctrl@3440000{
+			compatible = "qcom,sm8450-lpass-lpi-pinctrl";
+			reg = <0 0x3440000 0x0 0x20000>,
+			      <0 0x34d0000 0x0 0x10000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&lpass_tlmm 0 0 23>;
+
+			clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+			clock-names = "core", "audio";
+
+			wsa_swr_active: wsa-swr-active-state {
+				clk-pins {
+					pins = "gpio10";
+					function = "wsa_swr_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio11";
+					function = "wsa_swr_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			tx_swr_active: tx-swr-active-state {
+				clk-pins {
+					pins = "gpio0";
+					function = "swr_tx_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio1", "gpio2", "gpio14";
+					function = "swr_tx_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			rx_swr_active: rx-swr-active-state {
+				clk-pins {
+					pins = "gpio3";
+					function = "swr_rx_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio4", "gpio5";
+					function = "swr_rx_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			wsa2_swr_active: wsa2-swr-active-state {
+				clk-pins {
+					pins = "gpio15";
+					function = "wsa2_swr_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio16";
+					function = "wsa2_swr_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+		};
+
  		apps_smmu: iommu@15000000 {
  			compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
  			reg = <0 0x15000000 0 0x100000>;
@@ -3507,6 +3799,9 @@ lpass_ag_noc: interconnect@3c40000 {
  		};
  	};
+ sound: sound {
+	};
You asked another folk working on sa8540p to not include sound in the SoC dtsi.

Konrad

+
  	thermal-zones {
  		aoss0-thermal {
  			polling-delay-passive = <0>;



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux