On 12/11/2022 18:26, Bryan O'Donoghue wrote:
> Move the dts data for the rb3 navigation mezzanine into its own dts file.
>
> Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../sdm845-db845c-navigation-mezzanine.dts | 107 ++++++++++++++++++
> arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 99 ----------------
> 3 files changed, 108 insertions(+), 99 deletions(-)
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index d534888bcfe52..70ce09bc63a33 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -131,6 +131,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c-navigation-mezzanine.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-lg-judyln.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-lg-judyp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
> new file mode 100644
> index 0000000000000..7bd0a15c72657
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
> @@ -0,0 +1,107 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2022, Linaro Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sdm845-db845c.dts"
> +
> +&cci {
> + status = "okay";
> +};
> +
> +&camss {
> + vdda-phy-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l26a_1p2>;
> +
> + status = "okay";
> +
> + ports {
> + port@0 {
> + reg = <0>;
> + csiphy0_ep: endpoint {
> + data-lanes = <0 1 2 3>;
> + remote-endpoint = <&ov8856_ep>;
> + };
> + };
> + };
> +};
> +
> +&cci_i2c0 {
> + camera@10 {
> + compatible = "ovti,ov8856";
> + reg = <0x10>;
> +
> + /* CAM0_RST_N */
> + reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&cam0_default>;
> +
> + clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
> + clock-names = "xvclk";
> + clock-frequency = <19200000>;
> +
> + /*
> + * The &vreg_s4a_1p8 trace is powered on as a,
> + * so it is represented by a fixed regulator.
> + *
> + * The 2.8V vdda-supply and 1.2V vddd-supply regulators
> + * both have to be enabled through the power management
> + * gpios.
> + */
> + dovdd-supply = <&vreg_lvs1a_1p8>;
> + avdd-supply = <&cam0_avdd_2v8>;
> + dvdd-supply = <&cam0_dvdd_1v2>;
> +
> + status = "okay";
Drop it.
Best regards,
Krzysztof
