Re: [PATCH v4 3/3] arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Add navigation mezzanine dts

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 12/11/2022 13:17, Konrad Dybcio wrote:


On 12/11/2022 13:41, Bryan O'Donoghue wrote:
Move the dts data for the rb3 navigation mezzanine into its own dts file.

Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/Makefile             |   1 +
  .../sdm845-db845c-navigation-mezzanine.dts    | 109 ++++++++++++++++++
  arch/arm64/boot/dts/qcom/sdm845-db845c.dts    | 101 ----------------
  3 files changed, 110 insertions(+), 101 deletions(-)
  create mode 100644 arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index cd88efa19e750..5eadd251a0a16 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -132,6 +132,7 @@ dtb-$(CONFIG_ARCH_QCOM)    += sdm845-cheza-r1.dtb
  dtb-$(CONFIG_ARCH_QCOM)    += sdm845-cheza-r2.dtb
  dtb-$(CONFIG_ARCH_QCOM)    += sdm845-cheza-r3.dtb
  dtb-$(CONFIG_ARCH_QCOM)    += sdm845-db845c.dtb
+dtb-$(CONFIG_ARCH_QCOM)    += sdm845-db845c-navigation-mezzanine.dtb
  dtb-$(CONFIG_ARCH_QCOM)    += sdm845-lg-judyln.dtb
  dtb-$(CONFIG_ARCH_QCOM)    += sdm845-lg-judyp.dtb
  dtb-$(CONFIG_ARCH_QCOM)    += sdm845-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
new file mode 100644
index 0000000000000..0862ca30c8963
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "sdm845-db845c.dts"
+
+&cci {
+    status = "okay";
+};
+
+&camss {
+    vdda-phy-supply = <&vreg_l1a_0p875>;
+    vdda-pll-supply = <&vreg_l26a_1p2>;
+
+    status = "ok";
"okay" is preferred.

+
+    ports {
+        #address-cells = <1>;
+        #size-cells = <0>;
Looks like the -cells properties are defined in 845 dtsi already.


+        port@0 {
+            reg = <0>;
+            csiphy0_ep: endpoint {
+                data-lanes = <0 1 2 3>;
+                remote-endpoint = <&ov8856_ep>;
+            };
+        };
+    };
+};
+
+&cci_i2c0 {
+    camera@10 {
+        compatible = "ovti,ov8856";
+        reg = <0x10>;
+
+        /* CAM0_RST_N */
+        reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&cam0_default>;
+
+        clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+        clock-names = "xvclk";
+        clock-frequency = <19200000>;
+
+        /*
+         * The &vreg_s4a_1p8 trace is powered on as a,
+         * so it is represented by a fixed regulator.
+         *
+         * The 2.8V vdda-supply and 1.2V vddd-supply regulators
+         * both have to be enabled through the power management
+         * gpios.
+         */
+        dovdd-supply = <&vreg_lvs1a_1p8>;
+        avdd-supply = <&cam0_avdd_2v8>;
+        dvdd-supply = <&cam0_dvdd_1v2>;
+
+        status = "ok";
"okay" is prefered.

+
+        port {
+            ov8856_ep: endpoint {
+                link-frequencies = /bits/ 64
+                    <360000000 180000000>;
+                data-lanes = <1 2 3 4>;
+                remote-endpoint = <&csiphy0_ep>;
+            };
+        };
+    };
+};
+
+&cci_i2c1 {
+    camera@60 {
+        compatible = "ovti,ov7251";
+
+        /* I2C address as per ov7251.txt linux documentation */
+        reg = <0x60>;
+
+        /* CAM3_RST_N */
+        enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&cam3_default>;
+
+        clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+        clock-names = "xclk";
+        clock-frequency = <24000000>;
+
+        /*
+         * The &vreg_s4a_1p8 trace always powered on.
+         *
+         * The 2.8V vdda-supply regulator is enabled when the
+         * vreg_s4a_1p8 trace is pulled high.
+         * It too is represented by a fixed regulator.
+         *
+         * No 1.2V vddd-supply regulator is used.
+         */
+        vdddo-supply = <&vreg_lvs1a_1p8>;
+        vdda-supply = <&cam3_avdd_2v8>;
+
+        status = "disable";
Missing d

Konrad
+
+        port {
+            ov7251_ep: endpoint {
+                data-lanes = <0 1>;
+/*                remote-endpoint = <&csiphy3_ep>; */
+            };
+        };
+    };
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 3e7ceb0861eb0..f41c6d600ea8c 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -1174,107 +1174,6 @@ &pm8998_gpio {
  };
-&cci {
-    status = "okay";
-};
-
-&camss {
-    vdda-phy-supply = <&vreg_l1a_0p875>;
-    vdda-pll-supply = <&vreg_l26a_1p2>;
-
-    status = "ok";
-
-    ports {
-        #address-cells = <1>;
-        #size-cells = <0>;
-        port@0 {
-            reg = <0>;
-            csiphy0_ep: endpoint {
-                data-lanes = <0 1 2 3>;
-                remote-endpoint = <&ov8856_ep>;
-            };
-        };
-    };
-};
-
-&cci_i2c0 {
-    camera@10 {
-        compatible = "ovti,ov8856";
-        reg = <0x10>;
-
-        /* CAM0_RST_N */
-        reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
-        pinctrl-names = "default";
-        pinctrl-0 = <&cam0_default>;
-
-        clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
-        clock-names = "xvclk";
-        clock-frequency = <19200000>;
-
-        /*
-         * The &vreg_s4a_1p8 trace is powered on as a,
-         * so it is represented by a fixed regulator.
-         *
-         * The 2.8V vdda-supply and 1.2V vddd-supply regulators
-         * both have to be enabled through the power management
-         * gpios.
-         */
-        dovdd-supply = <&vreg_lvs1a_1p8>;
-        avdd-supply = <&cam0_avdd_2v8>;
-        dvdd-supply = <&cam0_dvdd_1v2>;
-
-        status = "ok";
-
-        port {
-            ov8856_ep: endpoint {
-                link-frequencies = /bits/ 64
-                    <360000000 180000000>;
-                data-lanes = <1 2 3 4>;
-                remote-endpoint = <&csiphy0_ep>;
-            };
-        };
-    };
-};
-
-&cci_i2c1 {
-    camera@60 {
-        compatible = "ovti,ov7251";
-
-        /* I2C address as per ov7251.txt linux documentation */
-        reg = <0x60>;
-
-        /* CAM3_RST_N */
-        enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
-        pinctrl-names = "default";
-        pinctrl-0 = <&cam3_default>;
-
-        clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
-        clock-names = "xclk";
-        clock-frequency = <24000000>;
-
-        /*
-         * The &vreg_s4a_1p8 trace always powered on.
-         *
-         * The 2.8V vdda-supply regulator is enabled when the
-         * vreg_s4a_1p8 trace is pulled high.
-         * It too is represented by a fixed regulator.
-         *
-         * No 1.2V vddd-supply regulator is used.
-         */
-        vdddo-supply = <&vreg_lvs1a_1p8>;
-        vdda-supply = <&cam3_avdd_2v8>;
-
-        status = "disable";
-
-        port {
-            ov7251_ep: endpoint {
-                data-lanes = <0 1>;
-/*                remote-endpoint = <&csiphy3_ep>; */
-            };
-        };
-    };
-};
-
  /* PINCTRL - additions to nodes defined in sdm845.dtsi */
  &qup_spi0_default {
      config {

Hmm.

I wasn't really looking to do anything other than move existing upstream stuff from one location to another.

But, since you flag it I will generate a number of Fixes: and append them to the head of this series.

---
bod



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux