Re: [PATCH 4/4] arm64: dts: qcom: add sdm670 and pixel 3a device trees

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 02/11/2022 00:57, Richard Acayan wrote:
The Qualcomm Snapdragon 670 has been out for a while. Add a device tree
for it and the Google Pixel 3a as the first device.

The Pixel 3a has the same bootloader issue as the Pixel 3 and will not work
on Android 10 bootloaders or later until it gets fixed for the Pixel 3.

SoC Initial Features:
  - power management
  - clocks
  - pinctrl
  - eMMC
  - USB 2.0
  - GENI I2C
  - IOMMU
  - RPMh
  - interrupts

Device-Specific Initial Features:
  - side buttons (keys)
  - regulators
  - touchscreen

Signed-off-by: Richard Acayan <mailingradian@xxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/Makefile             |    1 +
  .../boot/dts/qcom/sdm670-google-sargo.dts     |  519 +++++++
  arch/arm64/boot/dts/qcom/sdm670.dtsi          | 1216 +++++++++++++++++
  3 files changed, 1736 insertions(+)
  create mode 100644 arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
  create mode 100644 arch/arm64/boot/dts/qcom/sdm670.dtsi

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index b0558d3389e5..4eb5d8829efb 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -124,6 +124,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-voyager.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm632-fairphone-fp3.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm636-sony-xperia-ganges-mermaid.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-xiaomi-lavender.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm670-google-sargo.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
new file mode 100644
index 000000000000..fa3dee78e442
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
@@ -0,0 +1,519 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for Google Pixel 3a, adapted from google-blueline device tree,
+ * xiaomi-lavender device tree, and oneplus-common device tree.
+ *
+ * Copyright (c) 2022, Richard Acayan. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include "sdm670.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &adsp_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+
+/ {
+	model = "Google Pixel 3a";
+	compatible = "google,sargo", "qcom,sdm670";
+	qcom,board-id = <0x00041e05 0>;
+	qcom,msm-id = <321 0x20001>;
+
+	aliases { };
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer@9c000000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0x9c000000 0x0 (1080 * 2220 * 4)>;
+			width = <1080>;
+			height = <2220>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		mpss_region: mpss@8b000000 {

Please call the nodes memory@


+			reg = <0 0x8b000000 0 0x9800000>;
+			no-map;
+		};
+
+		venus_mem: venus@94800000 {
+			reg = <0 0x94800000 0 0x500000>;
+			no-map;
+		};
+
+		wlan_msa_mem: wlan-msa@94d00000 {
+			reg = <0 0x94d00000 0 0x100000>;
+			no-map;
+		};
+
+		cdsp_mem: cdsp@94e00000 {
+			reg = <0 0x94e00000 0 0x800000>;
+			no-map;
+		};
+
+		mba_region: mba@95600000 {
+			reg = <0 0x95600000 0 0x200000>;
+			no-map;
+		};
+
+		adsp_mem: adsp@95800000 {
+			reg = <0 0x95800000 0 0x2200000>;
+			no-map;
+		};
+
+		ipa_fw_mem: ipa-fw@97a00000 {
+			reg = <0 0x97a00000 0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: ipa-gsi@97a10000 {
+			reg = <0 0x97a10000 0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: gpu@97a15000 {
+			reg = <0 0x97a15000 0 0x2000>;
+			no-map;
+		};
+
+		framebuffer-region@9c000000 {
+			reg = <0 0x9c000000 0 0x2400000>;
+			no-map;
+		};
+
+		/* Also includes ramoops regions */

Isn't that counter-intuitive? Linux won't see it as ramoops then.


+		debug_info_mem: debug-info@a1800000 {
+			reg = <0 0xa1800000 0 0x411000>;
+			no-map;
+		};
+	};
+
+	/*
+	 * Supply map from xiaomi-lavender specifies this as the supply for
+	 * ldob1, ldob9, ldob10, ldoa2, and ldoa3, while downstream specifies
+	 * this as a power domain. Set this as a fixed regulator with the same
+	 * voltage as lavender until display is needed to avoid unneccessarily
+	 * using a deprecated binding (regulator-fixed-domain).
+	 */
+	vreg_s2b_1p05: vreg-s2b-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s2b";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3312000>;
+		regulator-max-microvolt = <3312000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_pin>;
+
+		key-vol-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * The touchscreen regulator seems to be controlled somehow by a gpio.
+	 * Model it as a fixed regulator and keep it on. Without schematics we
+	 * don't know how this is actually wired up...
+	 */
+	ts_1p8_supply: ts-1p8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ts_1p8_supply";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm660_gpios 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&apps_rsc {
+	pm660l-regulators {

New bindings changes dictate use of regulator-0 regulator-1 etc

node names. Also, is there any particular reason PMIC_B goes before

PMIC_A?


+		compatible = "qcom,pm660l-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vdd-l1-l9-l10-supply = <&vreg_s2b_1p05>;
+		vdd-l2-supply = <&vreg_bob>;
+		vdd-l3-l5-l7-l8-supply = <&vreg_bob>;
+		vdd-l4-l6-supply = <&vreg_bob>;
+		vdd-bob-supply = <&vph_pwr>;
+
+		/* LDOs */
+		vreg_l1b_0p89: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <900000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l2b_2p38: ldo2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l3b_2p93: ldo3 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l4b_2p96: ldo4 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l5b_2p96: ldo5 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l6b_3p15: ldo6 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l7b_3p1: ldo7 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8b_3p3: ldo8 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		/*
+		 * Downstream specifies a fixed voltage of 3.312 V, but the
+		 * PMIC4 BOB ranges don't support that. Widen the range a
+		 * little to avoid adding a new BOB regulator type.

Maybe the upstream driver is wrong then. Could somebody with docs recheck that?

And also pm8350 & pm8350c ranges while at it, pretty please?


+		 */
+		vreg_bob: bob {
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3328000>;
+			regulator-enable-ramp-delay = <500>;
+		};
+	};
+
+	pm660-regulators {
+		compatible = "qcom,pm660-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vdd-l1-l6-l7-supply = <&vreg_s6a_1p29>;
+		vdd-l2-l3-supply = <&vreg_s2b_1p05>;
+		vdd-l5-supply = <&vreg_s2b_1p05>;
+		vdd-l8-l9-l10-l11-l12-l13-l14-supply = <&vreg_s4a_1p92>;
+		vdd-l15-l16-l17-l18-l19-supply = <&vreg_bob>;
+
+		/*
+		 * S1A (FTAPC0), S2A (FTAPC1), S3A (HFAPC1) are managed
+		 * by the Core Power Reduction hardened (CPRh) and the
+		 * Operating State Manager (OSM) HW automatically.
+		 */
+
+		vreg_s4a_1p92: smps4 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-enable-ramp-delay = <200>;
+		};
+
+		vreg_s6a_1p29: smps6 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-enable-ramp-delay = <150>;
+		};
+
+		/* LDOs */
+		vreg_l1a_1p225: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l2a_1p0: ldo2 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l6a_1p28: ldo6 {
+			regulator-min-microvolt = <1248000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l7a_1p2: ldo7 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8a_1p8: ldo8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l9a_1p8: ldo9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l11a_1p8: ldo11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l13a_1p8: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l15a_2p38: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2696000>;
+			regulator-max-microvolt = <2696000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l17a_2p38: ldo17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l19a_3p3: ldo19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+	};
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};

Please sort the & references alphabetically.


+
+&i2c9 {
+	status = "okay";

status should be the last property (still before subnodes - otherwise you'll get a DTC error).

This applies to all occurences.


+	clock-frequency = <100000>;
+
+	synaptics-rmi4-i2c@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_default>;
+
+		/* VDD supply isn't specified, bind it to power */

I don't think it would explode if you just removed it then?


+		vdd-supply = <&vph_pwr>;
+		vio-supply = <&ts_1p8_supply>;
+
+		syna,reset-delay-ms = <200>;
+		syna,startup-delay-ms = <200>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			touchscreen-x-mm = <62>;
+			touchscreen-y-mm = <127>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+};
+
+&pm660l_gpios {
+	vol_up_pin: vol-up-state {
+		pins = "gpio7";
+		function = "normal";
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		input-enable;
+		bias-pull-up;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&sdhc_1 {
+	status = "okay";
+	supports-cqe;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	mmc-ddr-1_8v;
+
+	qcom,ddr-config = <0xc3040873>;
+
+	vmmc-supply = <&vreg_l4b_2p96>;
+	vqmmc-supply = <&vreg_l8a_1p8>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	touchscreen_default: ts-default-state {
+		ts-reset-pins {
+			pins = "gpio99";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+			output-high;
+		};
+
+		ts-irq-pins {
+			pins = "gpio125";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		ts-switch-pins {
+			pins = "gpio135";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+			output-low;
+		};
+	};
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p89>;
+	vdda-pll-supply = <&vreg_l10a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p1>;
+};
+
+&usb_1 {
+	status = "okay";
+
+	qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+	/* Only peripheral works for now */
+	dr_mode = "peripheral";
+
+	/* Do not assume that sdm670.dtsi will never support USB 3.0 */
+	phys = <&usb_1_hsphy>;
+	phy-names = "usb2-phy";
+	maximum-speed = "high-speed";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi
new file mode 100644
index 000000000000..4450ece839a0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi
@@ -0,0 +1,1216 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM670 SoC device tree source, adapted from SDM845 SoC device tree
+ *
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Richard Acayan. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdm845.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases { };
+
+	chosen { };
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0 0x80000000 0 0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: hyp-mem@85700000 {
+			reg = <0 0x85700000 0 0x600000>;
+			no-map;
+		};
+
+		xbl_mem: xbl-mem@85e00000 {
+			reg = <0 0x85e00000 0 0x100000>;
+			no-map;
+		};
+
+		aop_mem: aop-mem@85fc0000 {
+			reg = <0 0x85fc0000 0 0x20000>;
+			no-map;
+		};
+
+		aop_cmd_db_mem: aop-cmd-db-mem@85fe0000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x0 0x85fe0000 0 0x20000>;
+			no-map;
+		};
+
+		camera_mem: camera-mem@8ab00000 {
+			reg = <0 0x8ab00000 0 0x500000>;
+			no-map;
+		};
+
+		mpss_region: mpss@8b000000 {
+			reg = <0 0x8b000000 0 0x7e00000>;
+			no-map;
+		};
+
+		venus_mem: venus@92e00000 {
+			reg = <0 0x92e00000 0 0x500000>;
+			no-map;
+		};
+
+		wlan_msa_mem: wlan-msa@93300000 {
+			reg = <0 0x93300000 0 0x100000>;
+			no-map;
+		};
+
+		cdsp_mem: cdsp@93400000 {
+			reg = <0 0x93400000 0 0x800000>;
+			no-map;
+		};
+
+		mba_region: mba@93c00000 {
+			reg = <0 0x93c00000 0 0x200000>;
+			no-map;
+		};
+
+		adsp_mem: adsp@93e00000 {
+			reg = <0 0x93e00000 0 0x1e00000>;
+			no-map;
+		};
+
+		ipa_fw_mem: ipa-fw@95c00000 {
+			reg = <0 0x95c00000 0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: ipa-gsi@95c10000 {
+			reg = <0 0x95c10000 0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: gpu@95c15000 {
+			reg = <0 0x95c15000 0 0x2000>;
+			no-map;
+		};
+
+		spss_mem: spss@97b00000 {
+			reg = <0 0x97b00000 0 0x100000>;
+			no-map;
+		};
+
+		qseecom_mem: qseecom@9e400000 {
+			reg = <0 0x9e400000 0 0x1400000>;
+			no-map;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+				      compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_100>;
+			L2_100: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_200>;
+			L2_200: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_300>;
+			L2_300: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_400>;
+			L2_400: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_500>;
+			L2_500: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_600>;
+			L2_600: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo360";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
+			next-level-cache = <&L2_700>;
+			L2_700: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "little-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <702>;
+				exit-latency-us = <915>;
+				min-residency-us = <1617>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "big-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <526>;
+				exit-latency-us = <1854>;
+				min-residency-us = <2380>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x4100c244>;
+				entry-latency-us = <3263>;
+				exit-latency-us = <6562>;
+				min-residency-us = <9825>;
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	clocks {

Please sort nodes alphabetically.


+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <38400000>;

clock-frequency should be moved to the board DTS to indicate it's not

a part of the SoC itself, but rather it sits on the board.


+			clock-output-names = "xo_board";

This should actually not be necessary, if you pass "xo" to rpmcc..



+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32764>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdm670", "qcom,scm";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		CPU_PD0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: power-domain-cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: power-domain-cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: power-domain-cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: power-domain-cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: power-domain-cluster {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sdm670";
+			reg = <0 0x00100000 0 0x1f0000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK_A>,
+				 <&sleep_clk>;
+			clock-names = "bi_tcxo",
+				      "bi_tcxo_ao",
+				      "sleep_clk";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		sdhc_1: mmc@7c4000 {
+			compatible = "qcom,sdm670-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x007c4000 0 0x1000>,
+			      <0 0x007c5000 0 0x1000>,
+			      <0 0x007c8000 0 0x8000>;
+			reg-names = "hc", "cqhci", "ice";
+
+			interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_SDCC1_ICE_CORE_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>;
+			clock-names = "iface", "core", "xo", "ice", "bus";
+
+			iommus = <&apps_smmu 0x140 0xf>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc1_state_on>;
+			pinctrl-1 = <&sdc1_state_off>;
+			power-domains = <&rpmhpd SDM670_CX>;
+
+			bus-width = <8>;
+			non-removable;
+
+			status = "disabled";
+		};
+
+		gpi_dma0: dma-controller@800000 {
+			#dma-cells = <3>;
+			compatible = "qcom,sdm670-gpi-dma", "qcom,sdm845-gpi-dma";
+			reg = <0 0x00800000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <13>;
+			dma-channel-mask = <0xfa>;
+			iommus = <&apps_smmu 0x0016 0x0>;
+			status = "disabled";
+		};
+
+		qupv3_id_0: geniqup@8c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x008c0000 0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x3 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>;
+			interconnect-names = "qup-core";
+			status = "disabled";
+
+			i2c0: i2c@880000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00880000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_default>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c1: i2c@884000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00884000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_default>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c2: i2c@888000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00888000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_default>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c3: i2c@88c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0088c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_default>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c4: i2c@890000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00890000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_default>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c5: i2c@894000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_default>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c6: i2c@898000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00898000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_default>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c7: i2c@89c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0089c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_default>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
+						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		gpi_dma1: dma-controller@a00000 {
+			#dma-cells = <3>;
+			compatible = "qcom,sdm670-gpi-dma", "qcom,sdm845-gpi-dma";
+			reg = <0 0x00a00000 0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <13>;
+			dma-channel-mask = <0xfa>;
+			iommus = <&apps_smmu 0x06d6 0x0>;
+			status = "disabled";
+		};
+
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x00ac0000 0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x6c3 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a80000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_default>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a84000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_default>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a88000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_default>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_default>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a90000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_default>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_default>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_default>;
+				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			i2c15: i2c@a9c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_default>;
+				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SDM670_CX>;
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		tlmm: pinctrl@3400000 {
+			compatible = "qcom,sdm670-tlmm";
+			reg = <0 0x03400000 0 0xc00000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 151>;
+
+			qup_i2c0_default: qup-i2c0-default-state {
+				pins = "gpio0", "gpio1";
+				function = "qup0";
+			};
+
+			qup_i2c1_default: qup-i2c1-default-state {
+				pins = "gpio17", "gpio18";
+				function = "qup1";
+			};
+
+			qup_i2c2_default: qup-i2c2-default-state {
+				pins = "gpio27", "gpio28";
+				function = "qup2";
+			};
+
+			qup_i2c3_default: qup-i2c3-default-state {
+				pins = "gpio41", "gpio42";
+				function = "qup3";
+			};
+
+			qup_i2c4_default: qup-i2c4-default-state {
+				pins = "gpio89", "gpio90";
+				function = "qup4";
+			};
+
+			qup_i2c5_default: qup-i2c5-default-state {
+				pins = "gpio85", "gpio86";
+				function = "qup5";
+			};
+
+			qup_i2c6_default: qup-i2c6-default-state {
+				pins = "gpio45", "gpio46";
+				function = "qup6";
+			};
+
+			qup_i2c7_default: qup-i2c7-default-state {
+				pins = "gpio93", "gpio94";
+				function = "qup7";
+			};
+
+			qup_i2c8_default: qup-i2c8-default-state {
+				pins = "gpio65", "gpio66";
+				function = "qup8";
+			};
+
+			qup_i2c9_default: qup-i2c9-default-state {
+				pins = "gpio6", "gpio7";
+				function = "qup9";
+			};
+
+			qup_i2c10_default: qup-i2c10-default-state {
+				pins = "gpio55", "gpio56";
+				function = "qup10";
+			};
+
+			qup_i2c11_default: qup-i2c11-default-state {
+				pins = "gpio31", "gpio32";
+				function = "qup11";
+			};
+
+			qup_i2c12_default: qup-i2c12-default-state {
+				pins = "gpio49", "gpio50";
+				function = "qup12";
+			};
+
+			qup_i2c13_default: qup-i2c13-default-state {
+				pins = "gpio105", "gpio106";
+				function = "qup13";
+			};
+
+			qup_i2c14_default: qup-i2c14-default-state {
+				pins = "gpio33", "gpio34";
+				function = "qup14";
+			};
+
+			qup_i2c15_default: qup-i2c15-default-state {
+				pins = "gpio81", "gpio82";
+				function = "qup15";
+			};
+
+			sdc1_state_on: sdc1-on-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <16>;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				rclk-pins {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+
+			sdc1_state_off: sdc1-off-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				rclk-pins {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+		};
+
+		usb_1_hsphy: phy@88e2000 {
+			compatible = "qcom,sdm670-qusb2-phy", "qcom,qusb2-v2-phy";
+			reg = <0 0x088e2000 0 0x400>;
+			status = "disabled";

Status last, please.


+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sdm670-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			dma-ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <150000000>;
+
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x740 0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_1_hsphy>;
+				phy-names = "usb2-phy";
+			};
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0 0x0c440000 0 0x1100>,
+			      <0 0x0c600000 0 0x2000000>,
+			      <0 0x0e600000 0 0x100000>,
+			      <0 0x0e700000 0 0xa0000>,
+			      <0 0x0c40a000 0 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		apps_smmu: iommu@15000000 {
+			/*
+			 * The hardware tolerates the SDM845 reset quirk. The
+			 * iommu maintainers aren't responding to any patches
+			 * that would add support for new platforms. Set this
+			 * compatible so this dtsi is valid and functional.

Not sure if this is the right approach. SDM670 is more or less a factory reject 845,

but the software stack may be hiding some differences..


Konrad

+			 */
+			compatible = "qcom,sdm845-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x80000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		apps_rsc: rsc@179c0000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0 0x179c0000 0 0x10000>,
+			      <0 0x179d0000 0 0x10000>,
+			      <0 0x179e0000 0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS  2>,
+					  <SLEEP_TCS   3>,
+					  <WAKE_TCS    3>,
+					  <CONTROL_TCS 1>;
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sdm670-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdm670-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0 0x17a00000 0 0x10000>,     /* GICD */
+			      <0 0x17a60000 0 0x100000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux