Re: [PATCH v4 0/4] media: camss: sm8250: Virtual channels support for SM8250

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 17/10/2022 16:06, Kieran Bingham wrote:
Quoting Bryan O'Donoghue (2022-10-17 01:16:05)
On 13/10/2022 13:12, quic_mmitkov@xxxxxxxxxxx wrote:
From: Milen Mitkov <quic_mmitkov@xxxxxxxxxxx>

For v4:
- fixes the warning reported by the kernel test robot
- tiny code change to enable the vc functionality with the partially-applied
    multistream patches on linux-next (tested on tag:next-20221010)

For v3:
- setting the sink pad format on the CSID entity will now propagate the
    format to the source pads to keep the subdev in a valid internal state.
- code syntax improvements

For v2:
- code syntax improvements
- The info print for the enabled VCs was demoted to a dbg print. Can be
    enabled with dynamic debug, e.g.:
echo "file drivers/media/platform/qcom/camss/* +p" > /sys/kernel/debug/dynamic_debug/control

NOTE: These changes depend on the multistream series, that as of yet
is still not merged upstream. However, part of the
multistream patches are merged in linux-next (tested on
tag:next-20221010), including the patch that introduces the
video_device_pipeline_alloc_start() functionality. This allows
applying and using this series on linux-next without applying the
complete multistream set.

The CSID hardware on SM8250 can demux the input data stream into
maximum of 4 multiple streams depending on virtual channel (vc)
or data type (dt) configuration.

Situations in which demuxing is useful:
- HDR sensors that produce a 2-frame HDR output, e.g. a light and a dark frame
    (the setup we used for testing, with the imx412 sensor),
    or a 3-frame HDR output - light, medium-lit, dark frame.
- sensors with additional metadata that is streamed over a different
    virtual channel/datatype.
- sensors that produce frames with multiple resolutions in the same pixel
    data stream

With these changes, the CSID entity has, as it did previously, a single
sink port (0), and always exposes 4 source ports (1, 2,3, 4). The
virtual channel configuration is determined by which of the source ports
are linked to an output VFE line. For example, the link below will
configure the CSID driver to enable vc 0 and vc 1:

media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'

which will be demuxed and propagated into /dev/video0
and /dev/video1 respectively. With this, the userspace can use
any normal V4L2 client app to start/stop/queue/dequeue from these
video nodes. Tested with the yavta app.

The format of each RDI channel of the used VFE(s) (msm_vfe0_rdi0,
msm_vfe0_rdi1,...) must also be configured explicitly.

Note that in order to keep a valid internal subdevice state,
setting the sink pad format of the CSID subdevice will propagate
this format to the source pads. However, since the CSID hardware
can demux the input stream into several streams each of which can
be a different format, in that case each source pad's
format must be set individually, e.g.:

media-ctl -V '"msm_csid0":1[fmt:SRGGB10/3840x2160]'
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/960x540]'

Milen Mitkov (4):
    media: camss: sm8250: Virtual channels for CSID
    media: camss: vfe: Reserve VFE lines on stream start and link to CSID
    media: camss: vfe-480: Multiple outputs support for SM8250
    media: camss: sm8250: Pipeline starting and stopping for multiple
      virtual channels

   .../platform/qcom/camss/camss-csid-gen2.c     | 54 ++++++++++------
   .../media/platform/qcom/camss/camss-csid.c    | 44 +++++++++----
   .../media/platform/qcom/camss/camss-csid.h    | 11 +++-
   .../media/platform/qcom/camss/camss-vfe-480.c | 61 ++++++++++++-------
   drivers/media/platform/qcom/camss/camss-vfe.c |  7 +++
   .../media/platform/qcom/camss/camss-video.c   | 21 ++++++-
   drivers/media/platform/qcom/camss/camss.c     |  2 +-
   7 files changed, 140 insertions(+), 60 deletions(-)


Hi Milen

The set applies to next-20221013 including patch#4.

I can confirm it doesn't break anything for me - though my sensor is a
bog-standard imx577 so it doesn't have any VC support.

Interesting though - the IMX477 has the ability to convey metadata on a
separate VC... That's actually the thing holding back the RPi IMX477
driver from mainline, as the way it was anticipated to support multiple
data streams is with the new multiplexed streams API.

Note that while the streams series enables the support for multiple streams, metadata support is not included. This mainly means the metadata mbus/v4l2 formats.

We've had some discussions about this with Laurent and Sakari, and it sounds like a rather complex issue (although you can skip the problems by just adding a custom metadata format, which I'm doing in my work branch to test metadata).

 Tomi




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux