Quoting Douglas Anderson (2022-10-14 10:33:18)
> Back in the description of commit e440e30e26dd ("arm64: dts: qcom:
> sc7180: Avoid glitching SPI CS at bootup on trogdor") we described a
> problem that we were seeing on trogdor devices. I'll re-summarize here
> but you can also re-read the original commit.
>
> On trogdor devices, the BIOS is setting up the SPI chip select as:
> - mux special function (SPI chip select)
> - output enable
> - output low (unused because we've muxed as special function)
>
> In the kernel, however, we've moved away from using the chip select
> line as special function. Since the kernel wants to fully control the
> chip select it's far more efficient to treat the line as a GPIO rather
> than sending packet-like commands to the GENI firmware every time we
> want the line to toggle.
>
> When we transition from how the BIOS had the pin configured to how the
> kernel has the pin configured we end up glitching the line. That's
> because we _first_ change the mux of the line and then later set its
> output. This glitch is bad and can confuse the device on the other end
> of the line.
>
> The old commit e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid
> glitching SPI CS at bootup on trogdor") fixed the glitch, though the
> solution was far from elegant. It essentially did the thing that
> everyone always hates: encoding a sequential program in device tree,
> even if it's a simple one. It also, unfortunately, got broken by
> commit b991f8c3622c ("pinctrl: core: Handling pinmux and pinconf
> separately"). After that commit we did all the muxing _first_ even
> though the config (set the pin to output high) was listed first. :(
>
> I looked at ideas for how to solve this more properly. My first
> thought was to use the "init" pinctrl state. In theory the "init"
> pinctrl state is supposed to be exactly for achieving glitch-free
> transitions. My dream would have been for the "init" pinctrl to do
> nothing at all. That would let us delay the automatic pin muxing until
> the driver could set things up and call pinctrl_init_done(). In other
> words, my dream was:
>
> /* Request the GPIO; init it 1 (because DT says GPIO_ACTIVE_LOW) */
> devm_gpiod_get_index(dev, "cs", GPIOD_OUT_LOW);
> /* Output should be right, so we can remux, yay! */
> pinctrl_init_done(dev);
>
> Unfortunately, it didn't work out. The primary reason is that the MSM
> GPIO driver implements gpio_request_enable(). As documented in
> pinmux.h, that function automatically remuxes a line as a GPIO. ...and
> it does this remuxing _before_ specifying the output of the pin. You
> can see in gpiod_get_index() that we call gpiod_request() before
> gpiod_configure_flags(). gpiod_request() isn't passed any flags so it
> has no idea what the eventual output will be.
>
> We could have debates about whether or not the automatic remuxing to
> GPIO for the MSM pinctrl was a good idea or not, but at this point I
> think there is a plethora of code that's relying on it and I certainly
> wouldn't suggest changing it.
>
> Alternatively, we could try to come up with a way to pass the initial
> output state to gpio_request_enable() and plumb all that through. That
> seems like it would be doable, but we'd have to plumb it through
> several layers in the stack.
>
> This patch implements yet another alternative. Here, we specifically
> avoid glitching the first time a pin is muxed to GPIO function if the
> direction of the pin is output. The idea is that we can read the state
> of the pin before we set the mux and make sure that the re-mux won't
> change the state.
>
> NOTES:
> - We only do this the first time since later swaps between mux states
> might want to preserve the old output value. In other words, I
> wouldn't want to break a driver that did:
> gpiod_set_value(g, 1);
> pinctrl_select_state(pinctrl, special_state);
> pinctrl_select_default_state();
> /* We should be driving 1 even if "special_state" made the pin 0 */
> - It's safe to do this the first time since the driver _couldn't_ have
> explicitly set a state. In order to even be able to control the GPIO
> (at least using gpiod) we have to have requested it which would have
> counted as the first mux.
> - In theory, instead of keeping track of the first time a pin was set
> as a GPIO we could enable the glitch-free behavior only when
> msm_pinmux_request_gpio() is in the callchain. That works an enables
> my "dream" implementation above where we use an "init" state to
> solve this. However, it's nice not to have to do this. By handling
> just the first transition to GPIO we can simply let the normal
> "default" remuxing happen and we can be assured that there won't be
> a glitch.
>
> Before this change I could see the glitch reported on the EC console
> when booting. It would say this when booting the kernel:
> Unexpected state 1 in CSNRE ISR
>
> After this change there is no error reported.
>
> Note that I haven't reproduced the original problem described in
> e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at
> bootup on trogdor") but I could believe it might happen in certain
> timing conditions.
>
> Fixes: b991f8c3622c ("pinctrl: core: Handling pinmux and pinconf separately")
> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
> ---
Reviewed-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
