On 5.10.2022 20:30, Dzmitry Sankouski wrote:
> Here is changelogs:
>
> Changes for v2:
> - remove memory nodes before redefining
> - add board compatible to schema
> - remove board msm-id, add chassis type
> - remove common dtsi
> - move resin to pm8998 dtsi file
> - dts formatting
> - unsupported properties removed
> - add copyright
> - rebase on latest master(6.0.0-rc6)
> Changes for v3:
> - regulators nodes renamed to match pattern 'regulators-[01]'
> - duplicate cci1-default node deleted
> - add state suffix to '.*(active|suspend|default)' pinctrl
> - rebase on latest master(6.0.0)
> Changes for v4:
> - fix dts compilation errors(rename pinctrl label usages)
> Changes for v5:
> - use pm8005_regulators label
> Changes for v6:
> - add state suffix to all pinctrl
> - move status nodes to last position
> - disable resin node by default
> - move the debounce param to pm8998.dtsi file
> - place this patch after dt-binding patch
>
>
> ср, 5 окт. 2022 г. в 21:15, Dzmitry Sankouski <dsankouski@xxxxxxxxx>:
>>
>> New device support - Xiaomi Mi6 phone
>>
>> What works:
>> - storage
>> - usb
>> - power regulators
>>
>> Signed-off-by: Dzmitry Sankouski <dsankouski@xxxxxxxxx>
>> ---
>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>> .../boot/dts/qcom/msm8998-xiaomi-sagit.dts | 681 ++++++++++++++++++
>> arch/arm64/boot/dts/qcom/pm8998.dtsi | 8 +
>> 3 files changed, 690 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 1d86a33de528..0460aabf1b59 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
>> +dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>> new file mode 100644
>> index 000000000000..e44f6a745a2c
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
>> @@ -0,0 +1,681 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
>> + *
>> + * Copyright (c) 2022, The Linux Foundation. All rights reserved.
>> + * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@xxxxxxxxx>
>> + * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@xxxxxxxxx>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "msm8998.dtsi"
>> +#include "pm8005.dtsi"
>> +#include "pm8998.dtsi"
>> +#include "pmi8998.dtsi"
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/leds/common.h>
>> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>> +
>> +/*
>> + * Delete following upstream (msm8998.dtsi) reserved
>> + * memory mappings which are different in this device.
>> + */
>> +/delete-node/ &mpss_mem;
>> +/delete-node/ &venus_mem;
>> +/delete-node/ &mba_mem;
>> +/delete-node/ &slpi_mem;
>> +/delete-node/ &ipa_fw_mem;
>> +/delete-node/ &ipa_gsi_mem;
>> +/delete-node/ &gpu_mem;
>> +/delete-node/ &wlan_msa_mem;
>> +
>> +/ {
>> + model = "Xiaomi Mi 6";
>> + compatible = "xiaomi,sagit", "qcom,msm8998";
>> + chassis-type = "handset";
>> + /* Required for bootloader to select correct board */
>> + qcom,board-id = <30 0>;
>> +
>> + reserved-memory {
>> + /*
>> + * The following memory regions on downstream are "dynamically allocated"
>> + * but given the same addresses every time. Hard code them as these addresses
>> + * are where the Xiaomi signed firmware expects them to be.
>> + */
>> + ipa_fws_region: ipa@f7800000 {
memory@
>> + compatible = "shared-dma-pool";
>> + reg = <0x0 0xf7800000 0x0 0x5000>;
>> + no-map;
>> + };
>> +
>> + zap_shader_region: gpu@f7900000 {
memory@
>> + compatible = "shared-dma-pool";
>> + reg = <0x0 0xf7900000 0x0 0x2000>;
>> + no-map;
>> + };
>> +
>> + mpss_mem: memory@8d000000 {
>> + reg = <0x0 0x8d000000 0x0 0x7000000>;
>> + no-map;
>> + };
>> +
>> + venus_mem: memory@94000000 {
>> + reg = <0x0 0x94000000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + mba_mem: memory@94500000 {
>> + reg = <0x0 0x94500000 0x0 0x200000>;
>> + no-map;
>> + };
>> +
>> + slpi_mem: memory@94700000 {
>> + reg = <0x0 0x94700000 0x0 0x10000>;
>> + no-map;
>> + };
>> +
>> + ipa_fw_mem: memory@95600000 {
>> + reg = <0x0 0x95600000 0x0 0x10000>;
>> + no-map;
>> + };
>> +
>> + ipa_gsi_mem: memory@95610000 {
>> + reg = <0x0 0x95610000 0x0 0x5000>;
>> + no-map;
>> + };
>> +
>> + gpu_mem: memory@95615000 {
>> + reg = <0x0 0x95615000 0x0 0x100000>;
>> + no-map;
>> + };
>> +
>> + wlan_msa_mem: memory@95715000 {
>> + reg = <0x0 0x95715000 0x0 0x100000>;
>> + no-map;
>> + };
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> + label = "Volume buttons";
>> + autorepeat;
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&vol_up_key_default>;
>> +
>> + key-vol-up {
>> + label = "Volume up";
>> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_VOLUMEUP>;
>> + debounce-interval = <15>;
>> + wakeup-source;
>> + };
>> + };
>> +
>> + gpio-hall-sensor {
>> + compatible = "gpio-keys";
>> + label = "Hall effect sensor";
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&hall_sensor_default_state>;
>> +
>> + event-hall-sensor {
>> + label = "Hall Effect Sensor";
>> + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
>> + linux,input-type = <EV_SW>;
>> + linux,code = <SW_LID>;
>> + linux,can-disable;
>> + wakeup-source;
>> + };
>> + };
>> +
>> + vph_pwr: vph-pwr-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vph_pwr";
>> + regulator-min-microvolt = <3700000>;
>> + regulator-max-microvolt = <3700000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + disp_vddts_vreg: disp-vddts-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "disp-vddts-regulator";
>> + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + regulator-boot-on;
>> + };
>> +};
>> +
>> +&blsp1_i2c5 {
>> + pinctrl-names = "default", "sleep";
>> +
>> + touchscreen@20 {
>> + compatible = "syna,rmi4-i2c";
>> + reg = <0x20>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + interrupt-parent = <&tlmm>;
>> + interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
>> +
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&ts_active_state>;
>> + pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
>> +
>> + vdd-supply = <&disp_vddts_vreg>;
>> + vio-supply = <&vreg_l6a_1p8>;
>> +
>> + syna,reset-delay-ms = <20>;
>> + syna,startup-delay-ms = <20>;
>> +
>> + rmi4-f01@1 {
>> + reg = <0x01>;
>> + syna,nosleep-mode = <1>;
>> + };
>> +
>> + rmi4-f12@12 {
>> + reg = <0x12>;
>> + touchscreen-x-mm = <64>;
>> + touchscreen-y-mm = <114>;
>> + syna,sensor-type = <1>;
>> + syna,rezero-wait-ms = <20>;
>> + };
>> +
>> + rmi4-f1a@1a {
>> + reg = <0x1a>;
>> + syna,codes = <KEY_BACK KEY_APPSELECT>;
>> + };
>> + };
>> + status = "okay";
This generates a DTC warning. Status should be the last *property*. However,
properties must precede subnodes. This applies to all occurences.
>> +};
>> +
>> +&blsp1_i2c5_sleep {
>> + /delete-property/ bias-pull-up;
>> + bias-disable;
>> +};
>> +
>> +&blsp1_uart3 {
>> + bluetooth {
>> + compatible = "qcom,wcn3990-bt";
>> +
>> + vddio-supply = <&vreg_s4a_1p8>;
>> + vddxo-supply = <&vreg_l7a_1p8>;
>> + vddrf-supply = <&vreg_l17a_1p3>;
>> + vddch0-supply = <&vreg_l25a_3p3>;
>> + max-speed = <3200000>;
>> + };
>> + status = "okay";
>> +};
>> +
>> +&blsp1_uart3_on {
>> + rx {
>> + /delete-property/ bias-disable;
>> + /*
>> + * Configure a pull-up on 46 (RX). This is needed to
>> + * avoid garbage data when the TX pin of the Bluetooth
>> + * module is in tri-state (module powered off or not
>> + * driving the signal yet).
>> + */
>> + bias-pull-up;
>> + };
>> +
>> + cts {
>> + /delete-property/ bias-disable;
>> + /*
>> + * Configure a pull-down on 47 (CTS) to match the pull
>> + * of the Bluetooth module.
>> + */
>> + bias-pull-down;
>> + };
>> +};
>> +
>> +&blsp2_uart1 {
>> + status = "okay";
>> +};
>> +
>> +&pm8005_regulators {
>> + compatible = "qcom,pm8005-regulators";
>> +
>> + vdd_s1-supply = <&vph_pwr>;
>> +
>> + pm8005_s1: s1 { /* VDD_GFX supply */
>> + regulator-min-microvolt = <524000>;
>> + regulator-max-microvolt = <1100000>;
>> + regulator-enable-ramp-delay = <500>;
>> +
>> + /* hack until we rig up the gpu consumer */
>> + regulator-always-on;
>> + };
>> +};
>> +
>> +&pm8998_gpio {
>> + vol_up_key_default: vol-up-key-default-state {
>> + pins = "gpio6";
>> + function = "normal";
>> + bias-pull-up;
>> + input-enable;
>> + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
>> + };
>> +
>> + audio_mclk_pin: audio-mclk-pin-active-state {
>> + pins = "gpio13";
>> + function = "func2";
>> + power-source = <0>;
>> + };
>> +};
>> +
>> +&qusb2phy {
>> + vdda-pll-supply = <&vreg_l12a_1p8>;
>> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
>> + status = "okay";
>> +};
>> +
>> +&rpm_requests {
>> + regulators-0 {
>> + compatible = "qcom,rpm-pm8998-regulators";
>> +
>> + vdd_s1-supply = <&vph_pwr>;
>> + vdd_s2-supply = <&vph_pwr>;
>> + vdd_s3-supply = <&vph_pwr>;
>> + vdd_s4-supply = <&vph_pwr>;
>> + vdd_s5-supply = <&vph_pwr>;
>> + vdd_s6-supply = <&vph_pwr>;
>> + vdd_s7-supply = <&vph_pwr>;
>> + vdd_s8-supply = <&vph_pwr>;
>> + vdd_s9-supply = <&vph_pwr>;
>> + vdd_s10-supply = <&vph_pwr>;
>> + vdd_s11-supply = <&vph_pwr>;
>> + vdd_s12-supply = <&vph_pwr>;
>> + vdd_s13-supply = <&vph_pwr>;
>> + vdd_l1_l27-supply = <&vreg_s7a_1p025>;
>> + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
>> + vdd_l3_l11-supply = <&vreg_s7a_1p025>;
>> + vdd_l4_l5-supply = <&vreg_s7a_1p025>;
>> + vdd_l6-supply = <&vreg_s5a_2p04>;
>> + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
>> + vdd_l9-supply = <&vreg_bob>;
>> + vdd_l10_l23_l25-supply = <&vreg_bob>;
>> + vdd_l13_l19_l21-supply = <&vreg_bob>;
>> + vdd_l16_l28-supply = <&vreg_bob>;
>> + vdd_l18_l22-supply = <&vreg_bob>;
>> + vdd_l20_l24-supply = <&vreg_bob>;
>> + vdd_l26-supply = <&vreg_s3a_1p35>;
>> + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
>> +
>> + vreg_s3a_1p35: s3 {
>> + regulator-min-microvolt = <1352000>;
>> + regulator-max-microvolt = <1352000>;
>> + };
>> +
>> + vreg_s4a_1p8: s4 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-allow-set-load;
>> + };
>> +
>> + vreg_s5a_2p04: s5 {
>> + regulator-min-microvolt = <1904000>;
>> + regulator-max-microvolt = <2040000>;
>> + };
>> +
>> + vreg_s7a_1p025: s7 {
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1028000>;
>> + };
>> +
>> + vreg_l1a_0p875: l1 {
>> + regulator-min-microvolt = <880000>;
>> + regulator-max-microvolt = <880000>;
>> + };
>> +
>> + vreg_l2a_1p2: l2 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + };
>> +
>> + vreg_l3a_1p0: l3 {
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + };
>> +
>> + vreg_l5a_0p8: l5 {
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <800000>;
>> + };
>> +
>> + vreg_l6a_1p8: l6 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + vreg_l7a_1p8: l7 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + vreg_l8a_1p2: l8 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + };
>> +
>> + vreg_l9a_1p8: l9 {
>> + regulator-min-microvolt = <1808000>;
>> + regulator-max-microvolt = <2960000>;
>> + };
>> +
>> + vreg_l10a_1p8: l10 {
>> + regulator-min-microvolt = <1808000>;
>> + regulator-max-microvolt = <2960000>;
>> + };
>> +
>> + vreg_l11a_1p0: l11 {
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + };
>> +
>> + vreg_l12a_1p8: l12 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + vreg_l13a_2p95: l13 {
>> + regulator-min-microvolt = <1808000>;
>> + regulator-max-microvolt = <2960000>;
>> + };
>> +
>> + vreg_l14a_1p8: l14 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + vreg_l15a_1p8: l15 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + vreg_l16a_2p7: l16 {
>> + regulator-min-microvolt = <2704000>;
>> + regulator-max-microvolt = <2704000>;
>> + };
>> +
>> + vreg_l17a_1p3: l17 {
>> + regulator-min-microvolt = <1304000>;
>> + regulator-max-microvolt = <1304000>;
>> + };
>> +
>> + vreg_l18a_2p7: l18 {
>> + regulator-min-microvolt = <2704000>;
>> + regulator-max-microvolt = <2704000>;
>> + };
>> +
>> + vreg_l19a_3p0: l19 {
>> + regulator-min-microvolt = <3008000>;
>> + regulator-max-microvolt = <3008000>;
>> + };
>> +
>> + vreg_l20a_2p95: l20 {
>> + regulator-min-microvolt = <2960000>;
>> + regulator-max-microvolt = <2960000>;
>> + regulator-allow-set-load;
>> + };
>> +
>> + vreg_l21a_2p95: l21 {
>> + regulator-min-microvolt = <2960000>;
>> + regulator-max-microvolt = <2960000>;
>> + regulator-system-load = <800000>;
>> + regulator-allow-set-load;
>> + };
>> +
>> + vreg_l22a_2p85: l22 {
>> + regulator-min-microvolt = <2864000>;
>> + regulator-max-microvolt = <2864000>;
>> + };
>> +
>> + vreg_l23a_3p3: l23 {
>> + regulator-min-microvolt = <3312000>;
>> + regulator-max-microvolt = <3312000>;
>> + };
>> +
>> + vreg_l24a_3p075: l24 {
>> + regulator-min-microvolt = <3088000>;
>> + regulator-max-microvolt = <3088000>;
>> + };
>> +
>> + vreg_l25a_3p3: l25 {
>> + regulator-min-microvolt = <3104000>;
>> + regulator-max-microvolt = <3312000>;
>> + };
>> +
>> + vreg_l26a_1p2: l26 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-allow-set-load;
>> + };
>> +
>> + vreg_l28_3p0: l28 {
>> + regulator-min-microvolt = <3008000>;
>> + regulator-max-microvolt = <3008000>;
>> + };
>> +
>> + vreg_lvs1a_1p8: lvs1 { };
>> +
>> + vreg_lvs2a_1p8: lvs2 { };
>> + };
>> +
>> + regulators-1 {
>> + compatible = "qcom,rpm-pmi8998-regulators";
>> +
>> + vdd_bob-supply = <&vph_pwr>;
>> +
>> + vreg_bob: bob {
>> + regulator-min-microvolt = <3312000>;
>> + regulator-max-microvolt = <3600000>;
>> + };
>> + };
>> +};
>> +
>> +&tlmm {
>> + gpio-reserved-ranges = <0 4>, <81 4>;
>> +
>> + cci1_default_state: cci1-default-state {
>> + pins = "gpio19", "gpio20";
>> + function = "cci_i2c";
>> + bias-disable;
>> + drive-strength = <2>;
>> + };
>> +
>> + cdc_reset_n_state: cdc-reset-n-state {
>> + pins = "gpio64";
>> + function = "gpio";
>> + bias-pull-down;
>> + drive-strength = <16>;
>> + output-high;
>> + };
>> +
>> + hall_sensor_default_state: hall-sensor-default-state {
>> + pins = "gpio124";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + input-enable;
>> + };
>> +
>> + mdss_dsi_active_state: mdss-dsi-active-state {
>> + pins = "gpio94";
>> + function = "gpio";
>> + drive-strength = <8>;
>> + bias-disable;
>> + };
>> +
>> + mdss_dsi_suspend_state: mdss-dsi-suspend-state {
>> + pins = "gpio94";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-pull-down;
>> + };
>> +
>> + mdss_te_active_state: mdss-te-active-state {
>> + pins = "gpio10";
>> + function = "mdp_vsync_a";
>> + drive-strength = <2>;
>> + bias-pull-down;
>> + };
>> +
>> + mdss_te_suspend_state: mdss-te-suspend-state {
>> + pins = "gpio10";
>> + function = "mdp_vsync_a";
>> + drive-strength = <2>;
>> + bias-pull-down;
>> + };
>> +
>> + msm_mclk0_active_state: msm-mclk0-active-state {
>> + pins = "gpio13";
>> + function = "cam_mclk";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + msm_mclk0_suspend_state: msm-mclk0-suspend-state {
>> + pins = "gpio13";
>> + function = "cam_mclk";
>> + drive-strength = <2>;
>> + bias-pull-down;
>> + };
>> +
>> + msm_mclk1_active_state: msm-mclk1-active-state {
>> + pins = "gpio14";
>> + function = "cam_mclk";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + msm_mclk1_suspend_state: msm-mclk1-suspend-state {
>> + pins = "gpio14";
>> + function = "cam_mclk";
>> + drive-strength = <2>;
>> + bias-pull-down;
>> + };
>> +
>> + nfc_int_active_state: nfc-int-active-state {
>> + pins = "gpio92";
>> + function = "gpio";
>> + drive-strength = <6>;
>> + bias-pull-up;
>> + };
>> +
>> + nfc_int_suspend_state: nfc-int-suspend-state {
>> + pins = "gpio92";
>> + function = "gpio";
>> + drive-strength = <6>;
>> + bias-pull-up;
>> + };
>> +
>> + nfc_enable_active_state: nfc-enable-active-state {
>> + pins = "gpio12", "gpio116";
>> + function = "gpio";
>> + drive-strength = <6>;
>> + bias-pull-up;
>> + };
>> +
>> + nfc_enable_suspend_state: nfc-enable-suspend-state {
>> + pins = "gpio12", "gpio116";
>> + function = "gpio";
>> + drive-strength = <6>;
>> + bias-disable;
>> + };
>> +
>> + ts_active_state: ts-active-state {
>> + pins = "gpio89", "gpio125";
>> + function = "gpio";
>> + drive-strength = <16>;
>> + bias-pull-up;
>> + input-enable;
>> + };
>> +
>> + ts_int_suspend_state: ts-int-suspend-state {
>> + pins = "gpio125";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + ts_reset_suspend_state: ts-reset-suspend-state {
>> + pins = "gpio89";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + };
>> +
>> + wcd_int_n_state: wcd-int-n-state {
>> + pins = "gpio54";
>> + function = "gpio";
>> + bias-pull-down;
>> + drive-strength = <2>;
>> + input-enable;
>> + };
>> +
>> + wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
>> + pins = "gpio65";
>> + function = "gpio";
>> + bias-disable;
>> + drive-strength = <2>;
>> + output-low;
>> + };
>> +
>> + wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
>> + pins = "gpio66";
>> + function = "gpio";
>> + bias-disable;
>> + drive-strength = <2>;
>> + output-low;
>> + };
>> +};
>> +
>> +&pm8998_resin {
>> + linux,code = <KEY_VOLUMEDOWN>;
>> +};
You forgot to enable it.
Konrad
>> +
>> +&ufshc {
>> + vcc-supply = <&vreg_l20a_2p95>;
>> + vccq-supply = <&vreg_l26a_1p2>;
>> + vccq2-supply = <&vreg_s4a_1p8>;
>> + vcc-max-microamp = <750000>;
>> + vccq-max-microamp = <560000>;
>> + vccq2-max-microamp = <750000>;
>> + status = "okay";
>> +};
>> +
>> +&ufsphy {
>> + vdda-phy-supply = <&vreg_l1a_0p875>;
>> + vdda-pll-supply = <&vreg_l2a_1p2>;
>> + vddp-ref-clk-supply = <&vreg_l26a_1p2>;
>> + status = "okay";
>> +};
>> +
>> +&usb3 {
>> + /* Disable USB3 clock requirement as the device only supports USB2 */
>> + qcom,select-utmi-as-pipe-clk;
>> + status = "okay";
>> +};
>> +
>> +&usb3_dwc3 {
>> + /* Drop the unused USB 3 PHY */
>> + phys = <&qusb2phy>;
>> + phy-names = "usb2-phy";
>> +
>> + /* Fastest mode for USB 2 */
>> + maximum-speed = "high-speed";
>> +
>> + /* Force to peripheral until we can switch modes */
>> + dr_mode = "peripheral";
>> +};
>> +
>> +&wifi {
>> + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
>> + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
>> + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
>> + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
>> + status = "okay";
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
>> index d09f2954b6f9..7929fa64e1ef 100644
>> --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
>> @@ -52,6 +52,14 @@ pm8998_pwrkey: pwrkey {
>> bias-pull-up;
>> linux,code = <KEY_POWER>;
>> };
>> +
>> + pm8998_resin: resin {
>> + compatible = "qcom,pm8941-resin";
>> + bias-pull-up;
>> + interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
>> + debounce = <15625>;
>> + status = "disabled";
>> + };
>> };
>>
>> pm8998_temp: temp-alarm@2400 {
>> --
>> 2.30.2
>>
