Re: [PATCH 2/2] dt-bindings: pinctrl: qcom,sdm845: convert to dtschema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 01/10/2022 00:05, Rob Herring wrote:
> On Fri, 30 Sep 2022 22:05:29 +0200, Krzysztof Kozlowski wrote:
>> Convert Qualcomm SDM845 pin controller bindings to DT schema.  Keep
>> the parsing of pin configuration subnodes consistent with other Qualcomm
>> schemas (children named with '-state' suffix, their children with
>> '-pins').
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
>> ---
>>  .../bindings/pinctrl/qcom,sdm845-pinctrl.txt  | 176 ------------------
>>  .../bindings/pinctrl/qcom,sdm845-pinctrl.yaml | 158 ++++++++++++++++
>>  2 files changed, 158 insertions(+), 176 deletions(-)
>>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt
>>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml
>>
> 
> Running 'make dtbs_check' with the schema in this patch gives the
> following warnings. Consider if they are expected or the schema is
> incorrect. These may not be new warnings.
> 
> Note that it is not yet a requirement to have 0 warnings for dtbs_check.
> This will change in the future.
> 
> Full log is available here: https://patchwork.ozlabs.org/patch/
> 
> 
> pinctrl@3400000: 'ap-edp-bklten', 'ap-suspend-l-hog', 'ap_suspend_l_assert', 'ap_suspend_l_deassert', 'bios-flash-wp-r-l', 'cci0-default', 'cci0-sleep', 'cci1-default', 'cci1-sleep', 'ec-ap-int-l', 'edp-brij-en', 'edp-brij-irq', 'en-pp3300-dx-edp', 'h1-ap-int-odl', 'pen-eject-odl', 'pen-irq-l', 'pen-pdct-l', 'pen-rst-l', 'qspi-clk', 'qspi-cs0', 'qspi-cs1', 'qspi-data01', 'qspi-data12', 'quat_mi2s_active', 'quat_mi2s_sd0_active', 'quat_mi2s_sd0_sleep', 'quat_mi2s_sd1_active', 'quat_mi2s_sd1_sleep', 'quat_mi2s_sd2_active', 'quat_mi2s_sd2_sleep', 'quat_mi2s_sd3_active', 'quat_mi2s_sd3_sleep', 'quat_mi2s_sleep', 'qup-i2c0-default', 'qup-i2c1-default', 'qup-i2c10-default', 'qup-i2c11-default', 'qup-i2c12-default', 'qup-i2c13-default', 'qup-i2c14-default', 'qup-i2c15-default', 'qup-i2c2-default', 'qup-i2c3-default', 'qup-i2c4-default', 'qup-i2c5-default', 'qup-i2c6-default', 'qup-i2c7-default', 'qup-i2c8-default', 'qup-i2c9-default', 'qup-spi0-default', 'qup-spi1-default', 'qup-spi10-default', 'qup-spi11-default', 'qup-spi12-default', 'qup-spi13-default', 'qup-spi14-default', 'qup-spi15-default', 'qup-spi2-default', 'qup-spi3-default', 'qup-spi4-default', 'qup-spi5-default', 'qup-spi6-default', 'qup-spi7-default', 'qup-spi8-default', 'qup-spi9-default', 'qup-uart0-default', 'qup-uart1-default', 'qup-uart10-default', 'qup-uart11-default', 'qup-uart12-default', 'qup-uart13-default', 'qup-uart14-default', 'qup-uart15-default', 'qup-uart2-default', 'qup-uart3-default', 'qup-uart4-default', 'qup-uart5-default', 'qup-uart6-default', 'qup-uart7-default', 'qup-uart8-default', 'qup-uart9-default', 'sd-cd-odl', 'sdc2-clk', 'sdc2-cmd', 'sdc2-data', 'ts-int-l', 'ts-reset-l' do not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
> 	arch/arm64/boot/dts/qcom/sdm845-cheza-r1.dtb
> 	arch/arm64/boot/dts/qcom/sdm845-cheza-r2.dtb
> 	arch/arm64/boot/dts/qcom/sdm845-cheza-r3.dtb

This is fixed in patch #1 in this set, however for some reason DT
patchwork did not get it (maybe size too big?).

For reference, the patch is available in Qualcomm patchwork:
https://patchwork.kernel.org/project/linux-arm-msm/patch/20220930200529.331223-2-krzysztof.kozlowski@xxxxxxxxxx/

Best regards,
Krzysztof





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux