Re: [PATCH v1 2/2] dt-bindings: add bindings for QCOM flash LED

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 28/09/2022 04:42, Fenglin Wu wrote:
> Add binding document for flash LED module inside Qualcomm Technologies,
> Inc. PMICs.
> 
> Signed-off-by: Fenglin Wu <quic_fenglinw@xxxxxxxxxxx>

You did not Cc me on first patch, so difficult to say how much it
matches the driver... There is also no DTS.

> ---
>  .../bindings/leds/leds-qcom-flash.yaml        | 108 ++++++++++++++++++
>  1 file changed, 108 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml
> 
> diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml b/Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml
> new file mode 100644
> index 000000000000..52a99182961b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml


Filename matching compatible if there is one fallback (e.g.
qcom,spmi-flash-led.yaml).

> @@ -0,0 +1,108 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/leds/leds-qcom-flash.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Flash LED device inside Qualcomm Technologies, Inc. PMICs
> +
> +maintainers:
> +  - Fenglin Wu <quic_fenglinw@xxxxxxxxxxx>
> +
> +description: |
> +  Flash LED controller is present inside some Qualcomm Technologies, Inc. PMICs.
> +  The flash LED module can have different number of LED channels supported
> +  e.g. 3 or 4. There are some different registers between them but they can
> +  both support maximum current up to 1.5 A per channel and they can also support
> +  ganging 2 channels together to supply maximum current up to 2 A. The current
> +  will be split symmetrically on each channel and they will be enabled and
> +  disabled at the same time.
> +
> +properties:
> +  compatible:
> +    items:
> +      - enum:
> +          - qcom,spmi-flash-led
> +          - qcom,pm8150c-flash-led
> +          - qcom,pm8150l-flash-led
> +          - qcom,pm8350c-flash-led

I doubt these are all different. You should use fallback, which also
will make use of the "items" you used...

> +
> +  reg:
> +    description: address offset of the flash LED controller
> +    maxItems: 1
> +
> +patternProperties:
> +  "^led@[0-3]$":
> +    type: object
> +    $ref: common.yaml#
> +    unevaluatedProperties: false
> +    description:
> +      Represents the physical LED components which are connected to the flash LED channels' output.

Does not look like wrapped at 80.

Other places as well.

> +
> +    properties:

Does not look like you tested the bindings...

You miss here reg.

> +      led-sources:
> +        description: The HW indices of the flash LED channels that connect to the physical LED
> +        allOf:
> +          - minItems: 1
> +            maxItems: 2
> +            items:
> +              enum: [1, 2, 3, 4]
> +
> +      led-max-microamp:
> +        description: |
> +          The maximum current value when LED is not operating in flash mode (i.e. torch mode)
> +          Valid values when an LED is connected to one flash LED channel:
> +            5000 - 500000, step by 5000> +          Valid values when an LED is connected to two flash LED
channels:
> +            10000 - 1000000, step by 10000

You need minimum and maximum.

> +
> +      flash-max-microamp:
> +        description: |
> +          The maximum current value when LED is operating in flash mode.
> +          Valid values when an LED is connected to one flash LED channel:
> +            12500 - 1500000, step by 12500
> +          Valid values when an LED is connected to two flash LED channels:
> +            25000 - 2000000, step by 12500

You need minimum and maximum.


> +
> +      flash-max-timeout-us:
> +        description: |
> +          The maximum timeout value when LED is operating in flash mode.
> +          Valid values: 10000 - 1280000, step by 10000

You need minimum and maximum.

> +
> +    required:
> +      - led-sources
> +      - led-max-microamp

reg.

> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/leds/common.h>
> +    flash-led@ee00 {

Node name: led-controller

> +            compatible = "qcom,spmi-flash-led";
> +            reg = <0xee00>;
> +
> +            led@0 {

Test your bindings...

> +                    function = LED_FUNCTION_FLASH;

Use 4 spaces for indentation of example.

> +                    color = <LED_COLOR_ID_WHITE>;
> +                    led-sources = <1>, <4>;
> +                    led-max-microamp = <300000>;
> +                    flash-max-microamp = <2000000>;
> +                    flash-max-timeout-us = <1280000>;
> +                    function-enumerator = <0>;
> +            };
> +

Best regards,
Krzysztof




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux