Re: [PATCH 1/2] dt-bindings: usb: Introduce GPIO-based SBU mux

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Quoting Prashant Malani (2022-08-19 13:14:25)
> > This would do that for us, but when all four lanes are connected from
> > the qmp phy directly to the connector we could just as easily have done
> > it with one endpoint.
> >
> >         qmp_phy {
> >                 ports {
> >                         port@0 {
> >                                 reg = <0>;
> >                                 endpoint@0 {
> >                                         reg = <0>;
> >                                         remote-endpoint = <&usb_c_ss>;
> >                                         data-lanes = <1 2 3 0>
> >                                 };
> >                         };
> >                 };
> >         };
> >
> > So should we explicitly have two endpoints in the usb-c-connector for
> > the two pairs all the time, or should we represent that via data-lanes
> > and only split up the connector's endpoint if we need to connect the
> > usb-c-connector to two different endpoints?
>
> I like 2 endpoints to represent the usb-c-connector, but that doesn't seem
> to be compatible (without introducing `data-lanes`, at least) with all
> the various
> combinations on the remote side, if that remote side is a DRM bridge with DP
> output capability (like it6505 or anx7625).
> That type of DRM bridge supports 1, 2 or 4 lane DP connections.

Why can't the remote side that's a pure DP bridge (it6505) bundle
however many lanes it wants into one endpoint? If it's a pure DP bridge
we should design the bridge binding to have up to 4 endpoints, but
sometimes 2 or 1 and then overlay data-lanes onto that binding so that
we can tell the driver how to remap the lanes if it can. If the hardware
can't support remapping lanes then data-lanes shouldn't be in the
binding.

>
> So, how about 4 endpoints (1 for each SS lane) in the usb-c-connector port@1?
> That should support every conceivable configuration and bridge/PHY hardware.
> and also allows a way to specify any lane remapping (similar to what
> "data lanes" does)
> if that is required.
> Then we are consistent with what an endpoint represents, regardless of whether
> the DRM bridge has a DP panel (1,2 or 4 lane) or Type-C connector  (2
> or 4 lane) on its output side.

I'd like to think in terms of the usb-c-connector, where the DP altmode
doesn't support one lane of DP and USB is only carried across two SS
lanes. Essentially, two SS lanes are always together, hence the idea
that we should have two endpoints in the SS port@1. In the simple case
above it seems we can get away with only one endpoint in the SS port@1
which is probably fine? I just don't know how that is represented in the
schema, but I suspect making another endpoint optional in the SS port@1
is the way to go.

Will there ever be a time when all 4 usb-c-connector remote-endpoint
phandles point to endpoints that are child nodes of different ports
(i.e. different qmp_phy nodes) with a 4 endpoint schema? I don't think
that is possible, so 4 endpoints is flexible but also verbose. It also
means we would have to walk the endpoints to figure out lane remapping,
wheres we can simply find the endpoint in the DP bridge ports and look
at data-lanes directly.



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux