Re: [PATCH] arm64: dts: qcom: pm6350: add temp sensor and thermal zone config

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 12, 2022 at 04:06:47PM +0200, Luca Weiss wrote:
> Hi Krzysztof,
> 
> +CC Matthias Kaehlcke (author of patch mentioned further below)
> 
> On Fri Aug 12, 2022 at 3:36 PM CEST, Krzysztof Kozlowski wrote:
> > On 12/08/2022 14:44, Luca Weiss wrote:
> > > Add temp-alarm device tree node and a default configuration for the
> > > corresponding thermal zone for this PMIC. Temperatures are based on
> > > downstream values.
> > > 
> > > Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
> > > ---
> > > With this config I'm getting this in dmesg, not sure if it's a warning
> > > that should be solved or just an informative warning.
> > > 
> > > [    0.268256] spmi-temp-alarm c440000.spmi:pmic@0:temp-alarm@2400: No ADC is configured and critical temperature is above the maximum stage 2 threshold of 140 C! Configuring stage 2 shutdown at 140 C.
> > > 
> > > As far as I can tell, based on downstream dts this PMIC doesn't have an
> > > ADC.

I don't seem to have access to the datasheet, in any case that the ADC isn't
configured in the downstream dts doesn't necessarily mean the PMIC doesn't
have one. The PM6150 has one, and it is probably relatively close to the
PM6350.

> > You configure 145 and driver believes 140 is the limit, so it seems
> > warning should be addressed.
> 
> Hm...
> 
> >
> > From where did you get 145 degrees as limit? Downstream DTS?
> 
> Yes, downstream dts[0].
> 
> From what I can see in the downstream driver, it always disabled this
> "software override of stage 2 and 3 shutdowns"[1]
> 
> In mainline only since f1599f9e4cd6 ("thermal: qcom-spmi: Use PMIC
> thermal stage 2 for critical trip points") this check exists, which is
> not part of downstream (wasn't in 4.19 yet), where this software
> override tries to get enabled so that thermal core can handle this.
> 
> Any suggestion what I can do here? Maybe looking at msm-5.4 sources (and
> associated dts) might reveal something..?

I wouldn't necessarily consider QC downstream code as a reliable source of
truth ...

> Maybe newer SoCs/PMICs have a different config?

Commit aa92b3310c55 ("thermal/drivers/qcom-spmi-temp-alarm: Add support
for GEN2 rev 1 PMIC peripherals") added support for gen2 PMICs, which
actually have lower thresholds than gen1. From the log it seems that the
PM6350 is identified as gen1 device (max stage 2 threshold = 140 degC).

It seems setting the limit to 140 degC or one of the other stage 2
thresholds would be a reasonable course of action. stage 2 is the
threshold at which the PMIC is so hot that the system should shut
down, and 140 degC is the highest of the stage 2 thresholds. Even
if it was possible, what would be gained from setting the trip
point 5 degC higher?



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux