Since there are two variants of Xiaomi Poco F1, move the common nodes from
Tianma variant into a new common dtsi. The EBBG variant will also inherit
the new common dtsi.
Signed-off-by: Joel Selvaraj <joel.selvaraj@xxxxxxxxxxx>
---
.../qcom/sdm845-xiaomi-beryllium-common.dtsi | 595 ++++++++++++++++++
.../qcom/sdm845-xiaomi-beryllium-tianma.dts | 590 +----------------
2 files changed, 598 insertions(+), 587 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
new file mode 100644
index 000000000000..83edcb1171f5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/*
+ * Delete following upstream (sdm845.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &tz_mem;
+/delete-node/ &adsp_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &rmtfs_mem;
+
+/ {
+ model = "Xiaomi Pocophone F1";
+ compatible = "xiaomi,beryllium", "qcom,sdm845";
+ chassis-type = "handset";
+
+ /* required for bootloader to select correct board */
+ qcom,board-id = <69 0>;
+ qcom,msm-id = <321 0x20001>;
+
+ aliases {
+ hsuart0 = &uart6;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_pin_a>;
+
+ vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ /* Reserved memory changes from downstream */
+ reserved-memory {
+ tz_mem: memory@86200000 {
+ reg = <0 0x86200000 0 0x4900000>;
+ no-map;
+ };
+
+ adsp_mem: memory@8c500000 {
+ reg = <0 0x8c500000 0 0x1e00000>;
+ no-map;
+ };
+
+ wlan_msa_mem: memory@8e300000 {
+ reg = <0 0x8e300000 0 0x100000>;
+ no-map;
+ };
+
+ mpss_region: memory@8e400000 {
+ reg = <0 0x8e400000 0 0x7800000>;
+ no-map;
+ };
+
+ venus_mem: memory@95c00000 {
+ reg = <0 0x95c00000 0 0x500000>;
+ no-map;
+ };
+
+ cdsp_mem: memory@96100000 {
+ reg = <0 0x96100000 0 0x800000>;
+ no-map;
+ };
+
+ mba_region: memory@96900000 {
+ reg = <0 0x96900000 0 0x200000>;
+ no-map;
+ };
+
+ slpi_mem: memory@96b00000 {
+ reg = <0 0x96b00000 0 0x1400000>;
+ no-map;
+ };
+
+ spss_mem: memory@97f00000 {
+ reg = <0 0x97f00000 0 0x100000>;
+ no-map;
+ };
+
+ rmtfs_mem: memory@f6301000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0 0xf6301000 0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+ };
+
+ vreg_s4a_1p8: vreg-s4a-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&adsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
+};
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l1a_0p875: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a_0p8: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a_2p95: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_l17a_1p3: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l20a_2p95: ldo20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2968000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l21a_2p95: ldo21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2968000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l23a_3p3: ldo23 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l24a_3p075: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l25a_3p3: ldo25 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l26a_1p2: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ };
+ };
+};
+
+&cdsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
+};
+
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vreg_l26a_1p2>;
+
+ display_panel: panel@0 {
+ reg = <0>;
+ vddio-supply = <&vreg_l14a_1p8>;
+ vddpos-supply = <&lab>;
+ vddneg-supply = <&ibb>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ backlight = <&pmi8998_wled>;
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+ status = "disabled";
+
+ port {
+ panel_in_0: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+};
+
+&dsi0_out {
+ remote-endpoint = <&panel_in_0>;
+ data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+ status = "okay";
+ vdds-supply = <&vreg_l1a_0p875>;
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <GCC_LPASS_Q6_AXI_CLK>,
+ <GCC_LPASS_SWAY_CLK>;
+};
+
+&gmu {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
+ };
+};
+
+&ibb {
+ regulator-min-microvolt = <4600000>;
+ regulator-max-microvolt = <6000000>;
+ regulator-over-current-protection;
+ regulator-pull-down;
+ regulator-soft-start;
+ qcom,discharge-resistor-kohms = <300>;
+};
+
+&lab {
+ regulator-min-microvolt = <4600000>;
+ regulator-max-microvolt = <6000000>;
+ regulator-over-current-protection;
+ regulator-pull-down;
+ regulator-soft-start;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mss_pil {
+ status = "okay";
+ firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
+};
+
+&ipa {
+ status = "okay";
+ memory-region = <&ipa_fw_mem>;
+ firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
+};
+
+&pm8998_gpio {
+ vol_up_pin_a: vol-up-active {
+ pins = "gpio6";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pmi8998_wled {
+ status = "okay";
+ qcom,current-boost-limit = <970>;
+ qcom,ovp-millivolt = <29600>;
+ qcom,current-limit-microamp = <20000>;
+ qcom,num-strings = <2>;
+ qcom,switching-freq = <600>;
+ qcom,external-pfet;
+ qcom,cabc;
+};
+
+&pm8998_pon {
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
+&q6afedai {
+ qi2s@22 {
+ reg = <22>;
+ qcom,sd-lines = <0>;
+ };
+};
+
+&q6asmdai {
+ dai@0 {
+ reg = <0>;
+ };
+
+ dai@1 {
+ reg = <1>;
+ };
+
+ dai@2 {
+ reg = <2>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
+};
+
+&sound {
+ compatible = "qcom,db845c-sndcard";
+ pinctrl-0 = <&quat_mi2s_active
+ &quat_mi2s_sd0_active>;
+ pinctrl-names = "default";
+ model = "Xiaomi Poco F1";
+ audio-routing =
+ "RX_BIAS", "MCLK",
+ "AMIC1", "MIC BIAS1",
+ "AMIC2", "MIC BIAS2",
+ "AMIC3", "MIC BIAS3";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9340 0>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9340 1>;
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ sdc2_default_state: sdc2-default {
+ clk {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+ };
+
+ sdc2_card_det_n: sd-card-det-n {
+ pins = "gpio126";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ wcd_intr_default: wcd_intr_default {
+ pins = <54>;
+ function = "gpio";
+
+ input-enable;
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+};
+
+&uart6 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l26a_1p2>;
+ vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&venus {
+ status = "okay";
+ firmware-name = "qcom/sdm845/beryllium/venus.mbn";
+};
+
+&wcd9340{
+ pinctrl-0 = <&wcd_intr_default>;
+ pinctrl-names = "default";
+ clock-names = "extclk";
+ clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+ reset-gpios = <&tlmm 64 0>;
+ vdd-buck-supply = <&vreg_s4a_1p8>;
+ vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+ vdd-tx-supply = <&vreg_s4a_1p8>;
+ vdd-rx-supply = <&vreg_s4a_1p8>;
+ vdd-io-supply = <&vreg_s4a_1p8>;
+ qcom,micbias1-microvolt = <2700000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <2700000>;
+ qcom,micbias4-microvolt = <2700000>;
+};
+
+&wifi {
+ status = "okay";
+
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+ vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_uart6_default {
+ pinmux {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
+ };
+
+ cts {
+ pins = "gpio45";
+ bias-disable;
+ };
+
+ rts-tx {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
index d88dc07205f7..fcbef5ad2909 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
@@ -2,593 +2,9 @@
/dts-v1/;
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-#include <dt-bindings/sound/qcom,q6afe.h>
-#include <dt-bindings/sound/qcom,q6asm.h>
-#include "sdm845.dtsi"
-#include "pm8998.dtsi"
-#include "pmi8998.dtsi"
+#include "sdm845-xiaomi-beryllium-common.dtsi"
-/*
- * Delete following upstream (sdm845.dtsi) reserved
- * memory mappings which are different in this device.
- */
-/delete-node/ &tz_mem;
-/delete-node/ &adsp_mem;
-/delete-node/ &wlan_msa_mem;
-/delete-node/ &mpss_region;
-/delete-node/ &venus_mem;
-/delete-node/ &cdsp_mem;
-/delete-node/ &mba_region;
-/delete-node/ &slpi_mem;
-/delete-node/ &spss_mem;
-/delete-node/ &rmtfs_mem;
-
-/ {
- model = "Xiaomi Pocophone F1";
- compatible = "xiaomi,beryllium", "qcom,sdm845";
- chassis-type = "handset";
-
- /* required for bootloader to select correct board */
- qcom,board-id = <69 0>;
- qcom,msm-id = <321 0x20001>;
-
- aliases {
- hsuart0 = &uart6;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- autorepeat;
-
- pinctrl-names = "default";
- pinctrl-0 = <&vol_up_pin_a>;
-
- vol-up {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
- };
- };
-
- /* Reserved memory changes from downstream */
- reserved-memory {
- tz_mem: memory@86200000 {
- reg = <0 0x86200000 0 0x4900000>;
- no-map;
- };
-
- adsp_mem: memory@8c500000 {
- reg = <0 0x8c500000 0 0x1e00000>;
- no-map;
- };
-
- wlan_msa_mem: memory@8e300000 {
- reg = <0 0x8e300000 0 0x100000>;
- no-map;
- };
-
- mpss_region: memory@8e400000 {
- reg = <0 0x8e400000 0 0x7800000>;
- no-map;
- };
-
- venus_mem: memory@95c00000 {
- reg = <0 0x95c00000 0 0x500000>;
- no-map;
- };
-
- cdsp_mem: memory@96100000 {
- reg = <0 0x96100000 0 0x800000>;
- no-map;
- };
-
- mba_region: memory@96900000 {
- reg = <0 0x96900000 0 0x200000>;
- no-map;
- };
-
- slpi_mem: memory@96b00000 {
- reg = <0 0x96b00000 0 0x1400000>;
- no-map;
- };
-
- spss_mem: memory@97f00000 {
- reg = <0 0x97f00000 0 0x100000>;
- no-map;
- };
-
- rmtfs_mem: memory@f6301000 {
- compatible = "qcom,rmtfs-mem";
- reg = <0 0xf6301000 0 0x200000>;
- no-map;
-
- qcom,client-id = <1>;
- qcom,vmid = <15>;
- };
- };
-
- vreg_s4a_1p8: vreg-s4a-1p8 {
- compatible = "regulator-fixed";
- regulator-name = "vreg_s4a_1p8";
-
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-};
-
-&adsp_pas {
- status = "okay";
- firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
-};
-
-&apps_rsc {
- pm8998-rpmh-regulators {
- compatible = "qcom,pm8998-rpmh-regulators";
- qcom,pmic-id = "a";
-
- vreg_l1a_0p875: ldo1 {
- regulator-min-microvolt = <880000>;
- regulator-max-microvolt = <880000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l5a_0p8: ldo5 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l7a_1p8: ldo7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l12a_1p8: ldo12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l13a_2p95: ldo13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2960000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l14a_1p8: ldo14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- vreg_l17a_1p3: ldo17 {
- regulator-min-microvolt = <1304000>;
- regulator-max-microvolt = <1304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l20a_2p95: ldo20 {
- regulator-min-microvolt = <2960000>;
- regulator-max-microvolt = <2968000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l21a_2p95: ldo21 {
- regulator-min-microvolt = <2960000>;
- regulator-max-microvolt = <2968000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l23a_3p3: ldo23 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3312000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l24a_3p075: ldo24 {
- regulator-min-microvolt = <3088000>;
- regulator-max-microvolt = <3088000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l25a_3p3: ldo25 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3312000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l26a_1p2: ldo26 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-boot-on;
- };
- };
-};
-
-&cdsp_pas {
+&display_panel {
+ compatible = "tianma,fhd-video";
status = "okay";
- firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
-};
-
-&dsi0 {
- status = "okay";
- vdda-supply = <&vreg_l26a_1p2>;
-
- panel@0 {
- compatible = "tianma,fhd-video";
- reg = <0>;
- vddio-supply = <&vreg_l14a_1p8>;
- vddpos-supply = <&lab>;
- vddneg-supply = <&ibb>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- backlight = <&pmi8998_wled>;
- reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
-
- port {
- tianma_nt36672a_in_0: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
-};
-
-&dsi0_out {
- remote-endpoint = <&tianma_nt36672a_in_0>;
- data-lanes = <0 1 2 3>;
-};
-
-&dsi0_phy {
- status = "okay";
- vdds-supply = <&vreg_l1a_0p875>;
-};
-
-&gcc {
- protected-clocks = <GCC_QSPI_CORE_CLK>,
- <GCC_QSPI_CORE_CLK_SRC>,
- <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
- <GCC_LPASS_Q6_AXI_CLK>,
- <GCC_LPASS_SWAY_CLK>;
-};
-
-&gmu {
- status = "okay";
-};
-
-&gpu {
- status = "okay";
-
- zap-shader {
- memory-region = <&gpu_mem>;
- firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
- };
-};
-
-&ibb {
- regulator-min-microvolt = <4600000>;
- regulator-max-microvolt = <6000000>;
- regulator-over-current-protection;
- regulator-pull-down;
- regulator-soft-start;
- qcom,discharge-resistor-kohms = <300>;
-};
-
-&lab {
- regulator-min-microvolt = <4600000>;
- regulator-max-microvolt = <6000000>;
- regulator-over-current-protection;
- regulator-pull-down;
- regulator-soft-start;
-};
-
-&mdss {
- status = "okay";
-};
-
-&mss_pil {
- status = "okay";
- firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
-};
-
-&ipa {
- status = "okay";
- memory-region = <&ipa_fw_mem>;
- firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
-};
-
-&pm8998_gpio {
- vol_up_pin_a: vol-up-active {
- pins = "gpio6";
- function = "normal";
- input-enable;
- bias-pull-up;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
- };
-};
-
-&pmi8998_wled {
- status = "okay";
- qcom,current-boost-limit = <970>;
- qcom,ovp-millivolt = <29600>;
- qcom,current-limit-microamp = <20000>;
- qcom,num-strings = <2>;
- qcom,switching-freq = <600>;
- qcom,external-pfet;
- qcom,cabc;
-};
-
-&pm8998_pon {
- resin {
- compatible = "qcom,pm8941-resin";
- interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
- debounce = <15625>;
- bias-pull-up;
- linux,code = <KEY_VOLUMEDOWN>;
- };
-};
-
-/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
-&q6afedai {
- qi2s@22 {
- reg = <22>;
- qcom,sd-lines = <0>;
- };
-};
-
-&q6asmdai {
- dai@0 {
- reg = <0>;
- };
-
- dai@1 {
- reg = <1>;
- };
-
- dai@2 {
- reg = <2>;
- };
-};
-
-&qupv3_id_0 {
- status = "okay";
-};
-
-&sdhc_2 {
- status = "okay";
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
-
- vmmc-supply = <&vreg_l21a_2p95>;
- vqmmc-supply = <&vreg_l13a_2p95>;
-
- bus-width = <4>;
- cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
-};
-
-&sound {
- compatible = "qcom,db845c-sndcard";
- pinctrl-0 = <&quat_mi2s_active
- &quat_mi2s_sd0_active>;
- pinctrl-names = "default";
- model = "Xiaomi Poco F1";
- audio-routing =
- "RX_BIAS", "MCLK",
- "AMIC1", "MIC BIAS1",
- "AMIC2", "MIC BIAS2",
- "AMIC3", "MIC BIAS3";
-
- mm1-dai-link {
- link-name = "MultiMedia1";
- cpu {
- sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
- };
- };
-
- mm2-dai-link {
- link-name = "MultiMedia2";
- cpu {
- sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
- };
- };
-
- mm3-dai-link {
- link-name = "MultiMedia3";
- cpu {
- sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
- };
- };
-
- slim-dai-link {
- link-name = "SLIM Playback";
- cpu {
- sound-dai = <&q6afedai SLIMBUS_0_RX>;
- };
-
- platform {
- sound-dai = <&q6routing>;
- };
-
- codec {
- sound-dai = <&wcd9340 0>;
- };
- };
-
- slimcap-dai-link {
- link-name = "SLIM Capture";
- cpu {
- sound-dai = <&q6afedai SLIMBUS_0_TX>;
- };
-
- platform {
- sound-dai = <&q6routing>;
- };
-
- codec {
- sound-dai = <&wcd9340 1>;
- };
- };
-};
-
-&tlmm {
- gpio-reserved-ranges = <0 4>, <81 4>;
-
- sdc2_default_state: sdc2-default {
- clk {
- pins = "sdc2_clk";
- bias-disable;
- drive-strength = <16>;
- };
-
- cmd {
- pins = "sdc2_cmd";
- bias-pull-up;
- drive-strength = <10>;
- };
-
- data {
- pins = "sdc2_data";
- bias-pull-up;
- drive-strength = <10>;
- };
- };
-
- sdc2_card_det_n: sd-card-det-n {
- pins = "gpio126";
- function = "gpio";
- bias-pull-up;
- };
-
- wcd_intr_default: wcd_intr_default {
- pins = <54>;
- function = "gpio";
-
- input-enable;
- bias-pull-down;
- drive-strength = <2>;
- };
-};
-
-&uart6 {
- status = "okay";
-
- bluetooth {
- compatible = "qcom,wcn3990-bt";
-
- vddio-supply = <&vreg_s4a_1p8>;
- vddxo-supply = <&vreg_l7a_1p8>;
- vddrf-supply = <&vreg_l17a_1p3>;
- vddch0-supply = <&vreg_l25a_3p3>;
- max-speed = <3200000>;
- };
-};
-
-&ufs_mem_hc {
- status = "okay";
-
- reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
-
- vcc-supply = <&vreg_l20a_2p95>;
- vcc-max-microamp = <800000>;
-};
-
-&ufs_mem_phy {
- status = "okay";
-
- vdda-phy-supply = <&vreg_l1a_0p875>;
- vdda-pll-supply = <&vreg_l26a_1p2>;
-};
-
-&usb_1 {
- status = "okay";
-};
-
-&usb_1_dwc3 {
- dr_mode = "peripheral";
-};
-
-&usb_1_hsphy {
- status = "okay";
-
- vdd-supply = <&vreg_l1a_0p875>;
- vdda-pll-supply = <&vreg_l12a_1p8>;
- vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-
- qcom,imp-res-offset-value = <8>;
- qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
- qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
- qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
-};
-
-&usb_1_qmpphy {
- status = "okay";
-
- vdda-phy-supply = <&vreg_l26a_1p2>;
- vdda-pll-supply = <&vreg_l1a_0p875>;
-};
-
-&venus {
- status = "okay";
- firmware-name = "qcom/sdm845/beryllium/venus.mbn";
-};
-
-&wcd9340{
- pinctrl-0 = <&wcd_intr_default>;
- pinctrl-names = "default";
- clock-names = "extclk";
- clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
- reset-gpios = <&tlmm 64 0>;
- vdd-buck-supply = <&vreg_s4a_1p8>;
- vdd-buck-sido-supply = <&vreg_s4a_1p8>;
- vdd-tx-supply = <&vreg_s4a_1p8>;
- vdd-rx-supply = <&vreg_s4a_1p8>;
- vdd-io-supply = <&vreg_s4a_1p8>;
- qcom,micbias1-microvolt = <2700000>;
- qcom,micbias2-microvolt = <1800000>;
- qcom,micbias3-microvolt = <2700000>;
- qcom,micbias4-microvolt = <2700000>;
-};
-
-&wifi {
- status = "okay";
-
- vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
- vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
- vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
- vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
- vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
-};
-
-/* PINCTRL - additions to nodes defined in sdm845.dtsi */
-
-&qup_uart6_default {
- pinmux {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "qup6";
- };
-
- cts {
- pins = "gpio45";
- bias-disable;
- };
-
- rts-tx {
- pins = "gpio46", "gpio47";
- drive-strength = <2>;
- bias-disable;
- };
-
- rx {
- pins = "gpio48";
- bias-pull-up;
- };
};
--
2.37.1
